Honeywell Galaxy 2 User Manual

63
Galaxy 2 Series Installation Manual
01 = Bell Time
This is the amount of time that the sounders/bells activate after an alarm condition has occured. The duration
of the output is programmable within the range 01-30 minutes; the default is 15.
02 = Bell Delay
This parameter, when set to On, delays the operation of the bell for 10 minutes following an intruder alarm.
04 = Exit time
This is the amount of time that the user has to exit the premises after initiating a Full Set procedure. The Exit
Time is...

64
Galaxy 2 Series Installation Manual
07 = Intruder Resets
This parameter dictates what type of reset is required for a signalled intruder alarm. There are two settings:
0. User
This setting allows any user programmed with the following user types: user, manager, master, to reset a full
intruder alarm.
1. Remote (default)
This setting requires an engineer or remote reset for a signalled intruder alarm. If this option is selected on a
system where confirmed alarms are used, then the reset level required...

65
Galaxy 2 Series Installation Manual
12 = Banner
This parameter has three settings:
1. Top Line
2. Bottom Line
3. Show on Set
0 = Off (Blank display when Set)
1 = On (Display normal banner when set)
The Day Mode Banner display on keypads can be altered. The top and bottom row can be edited separately
with descriptors of up to 16 characters.  Each number key on the keypad is assigned several characters that
are accessed by pressing the key repeatedly until the desired character appears on the screen....

66
Galaxy 2 Series Installation Manual
Keypad tamper lockout is indicated on the keypad display. After 20 attempts, a tamper is logged and an event
is signalled. When option 2 or 3 are selected the same rules apply to wireless fobs and prox tags.
15 = SPK Mode
This function selects whether the LS (loudspeaker) terminal acts as a speaker driver or a normal switched
output. There are two settings.
0. Switch DC
1. SPK Driver
NOTE:Never connect a speaker to this terminal when the mode is set to Switch DC.
16...

67
Galaxy 2 Series Installation Manual
3. RF Jam
This option selects whether or not the system can be set while there is an RF Jam (interference condition)
present.
4. TEL Line Fault
When set to on a line fault can be detected by the panel.
A line fail prevents setting.
19 = Part Bells
This option determines whether the External Bell and Strobe outputs activate during an alarm condition when
the system is Part Set.
0.No
1. Yes (default)
NOTE:Internal sounders always sound.
20 = Night Bells
This option...

68
Galaxy 2 Series Installation Manual
24 = Entry Deviation
This parameter has two settings:
0.No
1. Yes (default)
If set to 0 (Entry Deviation not permitted), deviation from an entry route during entry or supplementary entry
periods will result in a Full Alarm Condition.
An entry route is defined as zones programmed as 01 (final) and 02 (exit).
Entry Deviation permitted (1) means that external bells/communications/triggers will be withheld until the entry
time expires. Entering a valid code before a...

69
Galaxy 2 Series Installation Manual
2. EOL Resistor
This selects the resistor value for the end of line (EOL) resistor used in EOL double balance zone configura-
tions. Normally this should be 1000 ohms. The value entered is in hundreds of ohms, 01 = 100 ohms,
99 = 9900 ohms.
3. Contact Res
As for EOL Resistor but for Contact resistor.
47 = Set confirm
This parameter gives an external indication when the system has set. There are three options:
0. Off
1. Strobe (flashes for two seconds)
2. Strobe &...

70
Galaxy 2 Series Installation Manual
6.RF Check
The RF Check is a means of warning the user that the system is unable to determine the status of the detector.
There are two options:
0 = No
This option disables the checking of the RF Stop Set (see Section 8, RF Stop Set).
1 = Yes
This option enables the checking of the RF stop set.
55 = DD243
The options of this parameter allow the confirmed alarm reporting operation to be modified to tailor the
system to requirements of DD243: 2002, depending on the...

71
Galaxy 2 Series Installation Manual
2 = Never Unset
The keypad can never unset the system. Unsetting can only be performed by a keyfob, proximity tag or
card.
NOTE:If the panel becomes locked by accidental selection of this option, the panel can be force
unset by the following procedure:
(a) Remove all power from the system.
(b) Open the panel lid tamper.
(c) Re-apply power.
The system will power up unset in a tamper condition.
4. Restart time
This option has two settings:
0 = No (default)
1 = If 1
st...

72
Galaxy 2 Series Installation Manual
8. Exit ZN conf.
0 = Before Entry (default)
1 = Except Entry
9. Entry clears conf.
This options selects whether a single (unconfirmed) alarm activation is remembered for the purposes of confir-
mation, after an entry door is open. This option has two settings:
0 = Reset Count
In this case, the confirmed alarm counter is reset to 0 as soon as an entry door is opened.
1 = Keep Count (default)
In this case, the confirmed alarm counter is maintained. If there is one...