Honeywell 1202g2 Manual

9 - 3
Resetting the Factory Defaults
If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want to restore the scan-
ner to factory default settings, first scan the Remove Custom Defaults bar code, then scan Activate Defaults.  Power cycle 
the scanner to reset it to the factory default settings.
Note: If using a cordless system, scanning the Activate Defaults bar code also causes both the scanner and the base or Access 
Point to perform a reset and become...

9 - 4 

10 - 1
10
Serial Programming Commands
The serial programming commands can be used in place of the programming bar codes.  Both the serial commands and the 
programming bar codes will program the scanner.  For complete descriptions and examples of each serial programming com-
mand, refer to the corresponding programming bar code in this manual.
The device must be set to an RS232 interface (see page 2-1).  The following commands can be sent via a PC COM port using 
terminal emulation software.
Conventions...

10 - 2
SubTag Field Usage 
When a query is used in place of a SubTag field, the query applies only to the subset of commands available that match the 
Tag field.  In this case, the Data field should not be used because it is ignored by the device.
Data Field Usage
When a query is used in place of the Data field, the query applies only to the specific command identified by the Tag and 
SubTag fields.
Concatenation of Multiple Commands
Multiple commands can be issued within one Prefix/Storage sequence....

10 - 3
This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on; 
the Start/Stop Character (SSX) is set to 0, or Don’t Transmit; 
the Check Character (CK2) is set to 0, or Not Required;
concatenation (CCT) is set to 1, or Enabled; 
the Minimum Message Length (MIN) is set to 2 characters; 
the Maximum Message Length (MAX) is set to 60 characters; 
and the Default setting (DFT) has no value.  
Serial Trigger Commands
You can activate and deactivate the scanner with serial...

10 - 4
Menu Commands
SelectionSetting* Indicates default
Serial Command
# Indicates a numeric entryPage
Product Default Settings
Setting Custom Defaults Set Custom Defaults MNUCDF1-6
Resetting the Custom Defaults Activate Custom Defaults DEFALT1-7
Programming the Interface
Plug and Play Codes Keyboard Wedge:
IBM PC AT and Compatibles with CR suffixPAP_AT2-1
IBM PS2 Keyboard PAPPS22-1
RS232 Serial Port PAP2322-1
Plug and Play Codes:
RS485IBM Port 5B Interface PAPP5B2-2
IBM Port 9B HHBCR-1 Interface...

10 - 5
Plug and Play Codes Verifone Ruby Terminal PAPRBY2-7
Gilbarco Terminal PAPGLB2-8
Honeywell Bioptic Aux Port PAPBIO2-8
Datalogic Magellan Bioptic Aux Port PAPMAG2-8
NCR Bioptic Aux Port PAPNCR2-9
Wincor Nixdorf Terminal PAPWNX2-9
Wincor Nixdorf Beetle PAPBTL2-10
Wincor Nixdorf RS232 Mode A PAPWMA2-10
Program Keyboard 
Country*U.S.A. KBDCTY02-11
Albania KBDCTY352-11
Arabic KBDCTY912-11
Azeri (Cyrillic) KBDCTY812-11
Azeri (Latin) KBDCTY802-11
Belarus KBDCTY822-11
Belgium KBDCTY12-11
Bosnia...

10 - 6
Greek (Latin) KBDCTY632-14
Greek (MS) KBDCTY662-14
Greek (Polytonic) KBDCTY602-14
Hebrew KBDCTY122-14
Hungarian (101 key) KBDCTY502-14
Hungary KBDCTY192-14
Iceland KBDCTY752-14
Ireland KBDCTY732-14
Italian (142) KBDCTY562-14
Italy KBDCTY52-14
Japan ASCII KBDCTY282-15
Kazakh KBDCTY782-15
Korea KBDCTY932-15
Kyrgyz (Cyrillic) KBDCTY792-15
Latin America KBDCTY142-15
Latvia KBDCTY422-15
Latvia (QWERTY) KBDCTY432-15
Lithuania KBDCTY442-15
Lithuania (IBM) KBDCTY452-15
Macedonia KBDCTY342-15
Malta...

10 - 7
Tatar KBDCTY852-18
Thailand KBDCTY942-18
Turkey F KBDCTY272-18
Turkey Q KBDCTY242-18
Ukrainian KBDCTY762-18
United Kingdom KBDCTY72-18
United Stated (Dvorak right) KBDCTY892-18
United States (Dvorak left) KBDCTY882-18
United States (Dvorak) KBDCTY872-18
United States (International) KBDCTY302-18
Uzbek (Cyrillic) KBDCTY772-18
Vietnam KBDCTY952-19
Keyboard Wedge Modifiers
ALT Mode *Off KBDALT02-19
4 Characters KBDALT72-19
Keyboard Style *Regular KBDSTY02-19
Caps Lock KBDSTY12-19
Shift Lock...

10 - 8
RS-232 Modifiers
RS232 Baud Rate 300 BPS 232BAD02-23
600 BPS 232BAD12-23
1200 BPS 232BAD22-23
2400 BPS 232BAD32-23
4800 BPS 232BAD42-23
*9600 BPS 232BAD52-23
19200 BPS 232BAD62-23
38400 BPS 232BAD72-23
57600 BPS 232BAD82-23
115200 BPS 232BAD92-23
Word Length:  Data Bits, Stop Bits, and 
Par ity7 Data, 1 Stop, Parity Even
232WRD32-24
7 Data, 1 Stop, Parity None 232WRD02-24
7 Data, 1 Stop, Parity Odd 232WRD62-24
7 Data, 2 Stop, Parity Even 232WRD42-24
7 Data, 2 Stop, Parity None 232WRD12-24
7 Data,...