Honda Bmw 5 Service Manual

--- - 
Maintenance 
Table c. Inspection II Service 
Additional 
New  parts  Warm engine  Dealer service  repair 
Tools  required  required  required  recommended  information 
Engine compartment  maintenance 
Replace  air filter  element.  (Note: reduce 
replacement intervals  in dusty operating 
conditions). 
Replace  brake 
fluid every 2 years  (time 
interval  begins from vehicle  production 
date). 
Cooling system  service 
Spark  plug service 
Brake 
system  maintenance 
:j: 
* 
Replace coolant...

020-1 0 
Maintenance Fluids and lubricants 
Table d. Engine  oil with  filter  change 
V-8 
models 
BMW  part no. 
07  510  017 868 
5W-30 synthetic  oil 
BMW  part no. 
07  51  0 017  866 
Specification 
1997 
- 1998 
15W-40 mineral oil 
Fluid 
6-cylinder  models 
Table  e. Manual  transmission  oil 
Approximate 
capacity 
6.5 
liters  (6.9 US qt) 
Specification 
Fluid 
I I 
Approximate 
capacity 
Getrag S5D 250G 1 .I liters  (1.2 US 
quarts)  BMW 
part no. 
83 22 408 942 
I 
quarts) 
Getrao 
S6S 420G...

020-1 1 
Maintenance 
Table g. Differential  oil 
(Lifetime  fluid; no fluid  change  required) 
Differential 
/Approximate. capaclty (in~t~al fill) I Spec~f~cat~on , , . 
G 1.6  liter 
(1.7  US 
at) I 
188 Compact I .O liter  BMW SAF-XO 
(1 .I US ql) synthetic oil 
1.4 
liler 220 1215 Compact US qt) I 
Table h. Engine Coolant 
Year,  model 
latent  heater: 
V-8  13.5 liter 
1997: 
6-cylinder 
V-8 
Table 
i. Brake  fluid 
Bralte system fiuld BMW hlgh 
performance,  DOT 4 
Approximate 
capacity 
9.9...

1 Maintenance 
NOTE- 
Castrol supplies  the mineral  and synthetic  oil recommend- 
ed  by 
BMW 
BMW High  Performance synthetic  oil may  be used  in all 
E39 models, regardless  of year. 
The  use of engine oil  additives is not  recommended  when 
using BMW High 
Performance synthetic engine oil. 
* BMW  is constantly upgrading  recommendedmaintenance 
procedures  and requirements.  The information contained 
here is  as accurate as  possible at the time  ofpublication. If 
there is any doubt  about...

4 If oil level  is low,  add oil by removing oil filler cap  (arrow) on 
top  of cylinder head 
(6-cylinder oil cap shown,  V-8 is sirnilar). 
- Add only amount needed  to bring oil  level to upper  mark on 
dipstick, using  an oil of correct viscosity and  grade. 
Engine oil and  filter,  changing 
A complete oil change requires  new oil, a  new filter insert  kit, 
and a new drain plug sealing  washer. The tools  needed, a 
17 
mm drain plug socket  or box wrench, a 36 mm socket or 
wrench,  and a...

020-1 4 
Maintenance 
- When oil flow  has diminished to an occasional drip,  reinstall 
drain  plug with a  new metal  sealing  washer and torque  plug. 
Tightening torque  Engine oil  drain plug to  oil pan 
25 Nrn (1.8 ft-lb) 
6-cylinder  oil filter assembly 
r------ 1 
< Working  at oil filter  housing (1): 
Lubricate  and install  new oil filter  O-rings (3, 4). 
Install a new filter  cartridge (5). 
lnstall and tighten  housing  cover (2). 
6-cylinder  oil filter  assembly  shown, V-8 is similar....

Maintenance 
< Release mass air flow sensor  clips (A). 
Release upper air filter housing clips (B). 
4 Lift air filter upper housing,  and  remove filter element. 
NOTE- 
V-8 engine  air filter assembly shown in illustration. 6-cylinder 
air  filter assembly  is similar  but located  at the  left front  of the 
engine compartment. 
- On  installation, install O-ring  for mass  air flow  sensor  into 
retaining clips in air filter upper  housing. 
- Replace air filter and upper  air filter housing,  and...

020-1 6 
Maintenance 
loose, hose is damaged,  or connection is dirty  or corroded. 
Dried coolant has  achalky appearance. Hoses should  be firm 
and  springy.  Replace  any hose  that is  cracked, has become 
soft  and limp,  or has been contaminated  by oil. 
4 As  a preventive  measure, replacement  of the  cooling system 
hoses  every four years  is recommended.  The illustration 
shows  examples  of damage  to coolant  hoses. Any of these 
conditions is cause  for replacement (illustration...

< 6-cylinder engine with  hydraulic  belt tensioners. 
Use long-handled  wrench to turn 
A/C belt tensioner (A) 
clockwise.  Remove AfC belt. 
* Similarly,  turn main  engine drive  belt tensioner (B) 
clockwise  and remove belt. 
< Some models have a dust cover over  belt tensioner  release 
lug, which must  be pried off prior to  removing belt. 
4 6-cylinder  engine with spring-loaded  belt tensioners. 
Use  long-handled  wrench to turn 
AfC belt  tensioner 
release  lug 
(A) clocltwise  (against...

020-1 8 
Maintenance 
V-8 engine drive belt diagram (NC belt not shown). 
NOTE- 
Two  types  of belt  tensioners are  used on the V-8 engines. 
The  tensioner shown  in this procedure  is for  cars  built up to 
8/97. The  later  style tensioner  is similar. 
4 V-8 engine  tensioner. 
Loosen 
fasteners(A) to  relieve  belt tension 
- Remove drive belt. 
4 When reinstalling belt,  check that it is correctly positioned on 
belt pulleys. 
With bolts 
(B and C) finger tight,  pretension adjuster  by...