Hitachi F7000 Instruction Manual

5.4 
5 - 17 
NOTICE:  1.  The data measured under the following condition will be 
saved automatically in Program Files\FL Solutions\Data.   
(Example:  C:Program Files\FL Solutions\Data)  
(1)  Measurement was carried out with “Auto File” 
specified and a file name unspecified.   
2.  The data measured under the following conditions will 
be saved automatically in Program Files\FL Solutions.   
(Example:  C:Program Files\FL Solutions)  
(2)  There is not an adequate free area in the specified 
storage...

5.5    Displaying Data in a Bird’s-Eye View 
5 - 18 
5.5    Displaying Data in a Bird’s-Eye View   
 
3-D Scan data can be displayed in a bird’s-eye view.   
Select the 
  (bird’s-eye view) button on the Spectrum toolbar.     
(Or select the bird’s-eye view command from the View menu.)     
 
 
 
Fig. 5-12 
 
 
Viewing direction is changeable by clicking 
 (from front),  
(from rear), 
  (from left) or  (from right).   
Clicking 
  (contour line diagram) displays a contour line diagram.   
 
  

5.6 
5 - 19 
5.6    Contour Scale Expansion with Mouse   
 
In the contour display of 3-D scan data, display scale can be expanded 
with the mouse.    On the Spectrum toolbar, click the 
 (contour 
scale expansion) button.    The button is set in the clicked status.   
 
 
 
Fig. 5-13 
 
 
Move the mouse cursor onto the contour as shown in Fig. 5-14 and drag 
the mouse along an area to be expanded with the left mouse button 
held down.   
  

5.6    Contour Scale Expansion with Mouse 
5 - 20 
 
 
 
Fig. 5-14 
 
 
The area enclosed with the mouse cursor is now expanded as shown in 
Fig. 5-15.    For restoring the original display, click the 
 (scale 
reset) button.   
 
 
 
Fig. 5-15 
 
 
For using the trace cursor on the contour window, click 
 again for 
returning to the non-clicked status.    

5.7 
5 - 21 
5.7    Auto Scale Display of Data   
 
When you click the 
  (auto scale) button on the data processing 
window after completion of measurement or from which the 3-D scan 
data file has been read out, the contour window, excitation spectrum 
window and emission spectrum window are displayed in the auto scale 
mode as shown in Fig. 5-16.   
 
 
 
Fig. 5-16    (Before execution of auto scale)    

5.7    Auto Scale Display of Data 
5 - 22 
 
 
 
Fig. 5-17    (After execution of auto scale) 
 
 
For restoring the original display, click the 
  (scale reset) button.   
 
  

5.8 
5 - 23 
5.8    Linking Trace Cursors from Peak Table   
 
On the data processing window where a contour and peak table are 
displayed, you may move the mouse cursor onto the peak table and 
click the mouse.    As a result, each trace cursor on the contour window, 
excitation spectrum window and emission spectrum window moves to 
the peak wavelength position.   
 
 
 
Fig. 5-18 
 
  

5.9  Data Printout 
5 - 24 
5.9  Data Printout  
 
Printout can be provided even when the function for automatic printout 
after measurement is not used.    The following two procedures are 
available.  
 
(1)  Click on the spectrum window, and the circumference turns blue.   
In this status, select the Print command from the File menu.     
Or click the 
  (print) button on the toolbar.    The field active 
on the data processing window (e.g., ①  in Fig. 5-11) will be 
printed.    What is displayed by...

5.9 
5 - 25 
(2)  Select the Report command in the Data menu.    Or click the  
button on the toolbar.    The Print Preview window will appear as 
shown below, so click Print.    Printout items should be selected 
at the Report tab in Spectrum Properties beforehand.   
 
 
 
Fig. 5-20 
 
 
NOTE:  If characters overflow from the print frame in repeat 
measurement or in overlaying, then change the printing 
orientation from vertical (Portrait) to horizontal (Landscape) at 
the Report tab in Fig. 5-21.   
  

5.9  Data Printout 
5 - 26 
Select the items to be printed in the following procedure.   
Click the 
  button, and the Spectrum Properties window will appear.     
↓ 
Select the Report tab, and the window in Fig. 5-21 will open.   
↓ 
In this window, select desired print items.   
 
 
 
Fig. 5-21