GTE Omni Si Database Technical Practices Manual

-
55
COL.NO.
27-30
32
33
34
35
36
37TL-130401Table 9.4Entry Fields for Record Code CA (Continued)
COL.NAME
3all Waiting
3ueue Timeout
Zontrol
3verflow to
Universal Night
AnswerAttendant
Y = allowed
Camp-on.=not allowed
Attendant Recall
on Hold
Attendant
Break-In
Attendant
Y = allowedPaging Queue
- = not allowed
Attendant
Paging
Attendant
Assignment for
Room-to-Room Blocking
Function
(Attendant
Assignment
Status)VALID
ENTRIES
f = UNA zone or
cones (l-4)
.=N/A
Y = allowed
. = not allowed
Y = allowed
- =...

TL-13CCOL.NO.
38-45
46
47
48
49TL-130400-1001
Record Code CN:9.5 Record Code CN, Figure 9.5, allows the system to have
Common Attendantcommon DNs (Directory Numbers) for a variety of Attendant
Directory NumbersConsole configurations.
,--- ---___~-------,---------------~---------------------------------------~-I
I;T T;II 2 2 IBI
I
I
I
II
II 
q ;’ I!I
I
I
I
I11rI...

TL-130400-1001
TRUNK
10.0 This section describes the record codes required to
FEATURESdefine the various system trunks and their features. The following
record codes are required:
l Record Code Tl defines the system trunk group parameters.
l Record Code T2 defines additional system trunk group
parameters.
x-.  .l Record Code CR defines system toll restriction.
l Record Code EC defines system expanded toll restriction.
l Record Code AS defines service codes allowed with toll
restriction.
l Record Code TC...

TL-130400-1001
Record Code Tl:Trunk Group Part 
- 110.1 Record Code 
Tl , Figure 10.1, provides parameters that are
used to define trunk groups within the system. Record Code T2
also provides parameters for defining trunk groups. Individual
trunks that make up the trunk groups are defined on Record
Code TC.
r---------
r---
r-----
r-------
r---
T---------------
7---7---f---7-~-7-------~(SEC) 
; (SEC) (II
I1I-T-T-t-T-T-t-T-T-t-i16161616161616166I1011 12131415161718.I-l-L-.J.~l-l-l~l-l-
CiI
I
I
I
I
I
I
I
I...

TL-130400-I 001COL.NO.
Table 10.1Entry Fields for Record Code Tl
COL.VALID
NAME
ENTRIESCOMMENTS
12-13Trunk Group
00-63 = number
NumberThis field determines the trunk group number.
-An RLT (Release Link Trunk) group does
s-not need trunk group assignment. The.”combined line and recording trunks are. . .allowed access to the distant toll operator if
seizure (loop or E&M) capability is allowed.
-The trunk group number must be unique
.-across this record code.
- Any trunk group defined here must also be...

TL-130400-1001Table 10.1Entry Fields for Record Code Tl (Continued)
COMMENTS
-If columns14-16 are markedCAS, the
displayable COS (Record Code DD) assigned
to the trunk group must be marked -- in
columns 
16-17 and 36-37, and SA in
columns 24-25. The dashes disallow
switched direct line and modem access, and
SA allows station access.
-If columns 
14-l 6 are marked COT, FXT, or
WTS and these are incoming trunks (marked
IN in columns 
21-22) the only allowed
features for the trunk group are trunk group...

TL-130400-1001Table 10.1Entry Fields for Record Code Tl (Continued)COMMENTS
Assign the trunk di
-If this field is marked OG or
-If this fieldis marked OG or --, columns
17-20 must be dashed. If this field is marked
IN or TW, columns 17-20 can be dashed or
marked with any allowable digit.
-If this field is marked TW, columns 23-30
must be marked withany validentry and not
-If this field is marked OG, columns 23-26
must be marked with dashes, and columns
27-30 can be marked with any valid entry but
must...

TL-130400-1001Table 10.1Entry Fields for Record Code Tl (Continued)
COMMENTS
-This fieldis sometimes used for remote
-Columns 25 and 26 are mutually exclusive.
-If a 
Y is entered in this field, an
dial pulse type signaling.
-Touch calling signaling can connect to
touch calling type signaling.
DP = lines that use dial pulse signaling
TC = lines that use touch calling signaling
MX = linesthat can
useDPor TCtype
-Return dial tone is used when a ground star
signal cannot be used as an indication to...

TL-130400-1001Table 10.1Entry Fields for Record Code Tl (Continued)
COL.COL.VALID
NO.NAME
ENTRIESCOMMENTS
3i -32Trunk
CA = incomingAssign the type of trunk disconnect
Disconnect
CD = outgoingsupervision for the trunk group.
Supervision
BT = incoming and-All references to the incoming or outgoing
outgoing (Tie)trunk calls are from the system point of view.
x-.-- = N/A
-Disconnect is defined as an on-hook
condition for 300 milliseconds after the answer
condition has been received.
-Loop start trunks...

TL-130400-1001Table 10.1
Entry Fields for Record Code Tl (Continued)COMMENTS
-The FB-17276 card has 4 circuits. Circuits
1 and 2 are loop; circuits 3 and 4 are E&M.
-If the 
AIOD option is used and no circuit is
defined, the default value is circuit 1.
-If used, the 
AIOD card must be defined on
Record Code FR.
-If this field is marked 
1, 2, 3, or 4, columns
33-34 must be marked AL.
number 
(CAMA) sending requirements.
ield allowsbillingidentification to the
-When a three-digit station numbering plan
is...