GTE Omni Si Database Technical Practices Manual

TL-130400-1001Table 10.1Entry Fields for Record Code Tl (Continued)
COL.COL.VALIDNO.NAMEENTRIESCOMMENTS
45-48Automatic Call
0000-9999 =
ICont’d) Distribution/number
Direct-In Line
(right justify
(ACD/DIL) Trunk three-digit
Pilot Numbernumbers)
mm-m = N/AFor the limited ACD feature to work properly, it
is recommended to use a pilot number from a
circular hunt group.
-If an entry (other than dashes) is made in
this field, columns 23-26 must be dashed.
-If an entry (other than dashes) is made in
this field,...

TL-130400-1001COL.NO.
Table 10.1Entry Fields for Record Code Tl (Continued)
COL.VALID
NAMEENTRIESCOMMENTS
55
56Trunk Homing
Selection
s-.”. . . .
._Automatic
Circuit
AssuranceH = allowed
- = not allowed
.-Y = selected
- = not selectedThis field determines whether or not the trunk
group is allowed homing.
-Entering an H in this field provides trunk
homing, which acts like a terminal hunt group.
-Normally a dash is recommended in this
field. This provides circular hunting.
NOTE: If this field is marked H,...

TL-130400-1001Table 10.1Entry Fields for Record Code Tl (Continued)
CQL.COL.VALID
NO.NAMEENTRIESCOMMENTS
65-67Automatic001-255 =Enter the number of minutes that a trunk must
Circuit
minutesbe seized before a report is made.
Assurance Long --- = not
-If this value is reached, a report is sent to
Calf Intervalselectedthe AttendantIMDR.45 = suggestedThis value should be set higher than the
valuenormal amount of time the site spends on a
call (e.g., a site that has the data option may_
be making long data...

TL-130400-1001Record Code T2:
Trunk Group Part 
- 210.2 Record Code T2, Figure 
10.2A, provides parameters that
define trunk groups. This record code is used along with Record
Code 
Tl in defining trunk groups.
Columns 14-28 are only used if toll restriction is in effect. If the
trunk group does not have toll restriction, dash columns 14-28.
Figures containing flowcharts and examples for toll restriction
configurations are included at the end of this record code.
Programming information is as follows:D-l...

TL-130400-1001
----------1--
; T;I RII A’; .!I
; CI
; 81I E’
; I;  
I;  
;
f i
; i
; I
; I
; I
f I
; I
I
- - -T T Tl--r--r--r--r--r--r--r-i~414141414~4,41’4~4’515151515151515151516l6’6l6,6l6’6~6~;-I~11213141516171819101112131415161718~91011121314151617118:I-L-I-L-I-L-L-I-L-*-L_L101-L-I-L-L-I-I-L-I-I-I-~-~-~-~-~-~---------------~-~
Figure 10.2A
Record Code T2: Trunk Group Data 2 Data Sheetv-------r---
Ir-
r---
r---------------------------------------ITI
I
I
I
1
I/I
I
II
II
I
I
I
II
I
I
I
I
I/I
II
I
I
SW...

TL-130400-1001
Table 10.2Entry Fields for Record Code T2COL.COL.VALID
NO.NAMEENTRIESCOMMENTS
12-13Trunk Group00-63 = number
This field determines the trunk group number.
Number
-If Record Code 
Tl , columns 14-l 6, are
marked 
DIG, PAG, REC, or NIC, columns 14-Y..e40 and 45-46 must be dashed.
.
-Each trunk group number on this record
code must appear on Record Code 
Tl,columns 12-l 3.
. .._-Trunk group numbers must be unique
’ 14-15across this record code.
Trunk TollTL = simple tollAssign the type of...

TL-130400-1001
Table 10.2Entry Fields for Record Code T2 (Continued)COMMENTS
-If toll restriction is
ineffect, for normal
applications this field will only be marked NM
-If this field is dashed, columns 18-20 and
23-25 must be dashed.
-If this field is not dashed, columns 18-20
and 23-25 must be marked 0-- to 999.
required for the trunk group.
-For normal applications, column 18 is
marked 1 and columns 19-20 are dashed.
-Columns 18-20 determine the digit while
columns 16-l 7 determine whether or not the...

TL-130400-1001COL.NO.
Table 10.2Entry Fields for Record Code T2 (Continued)
COL.VALID
NAMEENTRIESCOMMENTS
26Codel-8 = number
This field determines the code restriction table
Restriction
-=N/Anumber used by the trunk group.
Table Number-This field points to Record Code CR,
.”column 12. Column 12 is a table number for-..the allowed NPAIABC of that table.
-If an entry is made in this column, Record
Code CR must be completed.
. .
27Expanded orl-8 = numberThis field determines the expanded or
Conflicting
- =...

TL-130400-1001Table 10.2Entry Fields for Record Code T2 (Continued)COMMENTS
6= tandem PABX Tie trunks (This is used in a
tandem network, allowing incoming PABX
trunks to access CO lines as well as Tie
trunks to other 
PABXs.)
7= class 4 WATS trunks (normally a small CO
with limited capabilities)
8 = class 5 WATS trunks (This type of CO can
provide toll switching.)
9 = conference port
- = dictation access, recorder announcer
access, or N/A
ree-way pertains
to a three-way connection.
2= FX trunks, PABXCO...

TL-130400-1001Table 10.2Entry Fields for Record Code T2 (Continued)
COL.COL.VALID
NO.
NAMEENTRIES
33
34
35VlERS Pause
l-5 = seconds
Jalue/Escape.=N/A
s-.”
MERS Pause
dalue/Toll3arrier Code
3lockY = blocked
TransmissionN = not blocked
Ignore Reverse
Battery Check
Message MeterY = allowed
Pegs Indicator
- = not allowed 1-5 = seconds
- = N/A
36
37
8/87SVR 5210I = ignore battery
check
- = perform
battery checkCOMMENTS
After the escape digit is sent, this field
determines the amount of seconds the system...