GTE Omni Si Database Technical Practices Manual

TL-130400-1001Table 7.6Entry Fields for Record Code CH
COL.COL.VALID
NO.NAME
ENTRIESCOMMENTS
12-i4Old AccessOOO-### = numberEnter the access code that is to be
Codetemporarily changed.
-Columns 12-14 and 15-l 8 are mutually
exclusive. If you mark this field, do not mark
columns 
15-l 8.
. .-This feature can only be used for intercept,
Attendant Console(s), hunt group, or agent
group.
15-18Old Station
0000-9999 =This field defines the station number that is to
Numbernumberbe temporarily changed.
---- 
=...

TL-130400-1001
Record Code DF:7.7 Record Code DF, Figure 7.7, defines the default line divertCPG 5efaultcondition for lines assigned a divert destination on Record Code
LD, columns 45-48.Record Code DF:
7.7 Record Code DF, Figure 7.7, defines the default line divert
CPG 5efaultcondition for lines assigned a divert destination on Record Code
LD, columns 45-48.
‘---------r---rI
I, TI 
6
,---------------------------------------------------------------~
II ; I.I
iI
I: FII 5IIIIIIIIII _ I I _ I’ /-.“I’...

TL-130400-1001LINE8.0 This section describes the record codes required to
ASSIGNMENTdefine the various system lines. The following record codes are
required:
l Record Code LD defines the primary directory number for all
lines in the system and provides additional line information.
l Record Code LM is an extension of Record Code LD.
-=-.”. .l Record Code LA defines the various line or DSS (Direct Station
Select) appearances.
l Record Code LI is not input by the customer 

TL-130400-1007
Record Code LB:8.1 Record Code LD, Figure 8.1, defines the primary directory
Line Datanumber for every line in the system. If an Analog/Digital
Featurephone has additional appearances of control lines such
as CO (Central Office), non-primary control, or data lines, an
entry on this record code is needed for each line type. Use this
record code to route non-working lines to a changed number
intercept. Line circuits programmed on the Attendant Console
(Record Code AT) or office features...

Table 8.1Entry Fields for Record Code LDCOMMENTS
equippedline circuits in the system.
-Directory numbers can be chosen in 
three-and/or four-digit patterns.
digit line directory-Three-digit numbers must beright justified
-Dashes must be entered in this field if the
line is used for an APM or SPM that is used in
support of the PD-200 Data Option.
-The 
APMs/SPMs are not accessed by a line
number, but by an X.121 address.
-This record code is only used to provide the
sical location of the...

TL-130400-1001Table 8.1Entry Fields for Record Code LD (Continued)COMMENTS
instrument line
columns 28-29 (this allows
-If columns;6-19 are markedPOTS,PACT,
AlFP, DFPA, DIFP, APM, or SPM, columns
20-25 must not be dashed.
-If columns 16-l 9 are dashed, columns
20-25 must be dashed.
-All card locations must be defined on
Record Code FR.
Which card slot within the group is this card?
-Inorder toprovidedasequential
appearance of line numbers on the CPG (in
groups of eight 
), list all eight circuits of a...

TL-130400-1001Table 8.1Entry Fields for Record Code LD (Continued)
COL.COL.VALID
NO.NAME
ENTRIESCOMMENTS
28-29
. . . .Line Type
--1CO = central office
NP is used for a logical line, which appears in
line, as in keysoftware only and needs no line card.
system CO line-- (a double dash) is used for all tip and ring
(Featurephone)type telephones (e.g., the FeatureComm” and
DA = data lineAnswerComm” 1 and 2).
(DIFP)When defining line 2 on a PACET
Li = CAS(Programmable Attendant/Agent Console
,_ Main/ACD...

TL-130400-1001Table 8.1Entry Fields for Record Code LD (Continued)COMMENTS
-If this line is to belong to an intercom group,
this field determines which group it belongs to.
-Each line appearing on the same IFP can
be in the same or different intercom groups.
-If two lines have a DSS appearance of each
ns 28-29 (line type) are marked
, 
Ll, -- or NW, this field must be
-The number entered here must be defined
on Record Codes DC and DD.
-If columns 16-19 are marked POTS, PACT,
AIFP, DFPA, or DIFP, these...

TL-130400-1001Table 8.1Entry Fields for Record Code bD (Continued)COMMENTS
O-7 =FRLvalueAssign the FRL value given to this line.
-This can only be assigned if the FRL feature
is in effect (see Record Code OF, column 54).
-A value of 0 is the most restrictive; a value
of 7 is the least restrictive.
-This value is compared to the FRL value of
the trunk that the user is trying to access.
-If the FRL value of the user is the same as
or greater than the FRL value given to the
trunk, the call can be made.
-If...

TL-130400-1001COL.NO.Table 8.1Entry Fields for Record Code LD (Continued)COL.VALID
NAMEENTRIESCOMMENTS
43-44Individual
00-30 = number
Speed CallingIf the line is a member of an individual speed
-- = N/A
calling list, assign the list it belongs to.
_ List Number.-Only one station can be assigned to each
individual speed calling list.
-A system maximum of 31 stations can have
this feature.
,.-If columns 16-19 are marked APM, SPM,
or dashed, these columns must be dashed.
-If the line type is DA (columns...