GGP Italy SPA Brush Cutter TB 25 - TB 25CX, BJ 250 - 250D Instruction Manual

ITLOCALIZZAZIONE GUASTI19
LOCALIZZAZIONE GUASTI
Procedura di avvio non corretta
Carburazione non corretta
Candela imbrattata
Filtro carburante otturato
Filtro aria sporco
Carburazione non corretta
Carburazione non corretta
Candela con gap
(distanza tra elettrodi) errato
Carburazione non corretta
Miscela con errato rapporto benzina - olio
Macchina non si
avvia oppure non si
mantiene in moto 
PROBLEMAPROBABILE CAUSA AZIONE CORRETTIVA
Seguire istruzioni del Manuale utente.
Far regolare il carburatore presso...

IT
Potenza sonora misurata
(ISO 10884)
Pressione sonora
(EN 27917)
20DATI TECNICI
DATI TECNICI
* Massa secondo norma ISO 11806 (senza carburante, dispositivi di taglio e protezione) 
•  1sinistra (o anteriore) 
•  2destra (o posteriore)                             2 tempi raffreddato
ad aria
25.4 cm
3
0.8 kW
10.300 1/min
2.900 1/min
7.400 min
-1
Ø 25,4 mm
Centrifuga
LD L8RTF
Elettronica
WYJ 398
Benzina – olio 50:1
600 cm
3
Tipo di motore
Cilindrata
Potenza
Velocità massima di rotazione
Velocità minima di...

ENPRESENTATION21
Dear Customer,
Firstly, we wish to thank you for having chosen our products and hope that the use of this machine will
be extremely satisfying for you and fully meet your expectations.
This manual has been drawn up to allow your to get to know your machine well and use it in safe and
efficient conditions; please do not forget that it is an integral part of the machine and keep it to hand
to be consulted at all times and consign it with the machine if you should sell or lend it to...

22IDENTIFICATION OF THE MACHINE AND PARTSEN
IDENTIFICATION OF THE MACHINE AND PARTS
1) Motor
2) Spark plug
3) Starter handle
4) Starter lever
5) Primer
6) Air filter
7) Fuel tank cap
8) Rear handgrip
9) Throttle lever
10) Safety lever
11) Start/Stop switch
11a) Accelerator stop
lever
12) Harness connection
13) Safety spacer
14) Drive shaft 
15) Front handgrip
16) Front guard 
17) Gear head
18) Cutting head with
nylon line
19) Cutter disk
20) Ratings plate
RATINGS PLATE
1) Conformity mark to the directive...

1)Warning! Danger
2)Read the instruction booklet before using this
machine.
3)Your hearing is at risk of irreparable damage.
Anyone operating this machine under normal
conditions during continuous daily use may be
exposed to a noise level equal to or exceeding
85 dB (A). 
The operator must wear Personal Protective
Equipment (PPE). Whenever the machine is in
use, safety goggles must be worn to safeguard
against flying objects, as must ear protectors,
such as a soundproof helmet, in order to protect
the...

Each element of this machine is a potential safe-
ty hazard if used improperly or poorly main-
tained.
We recommend that special attention is paid to
the sections starting with the following headings:
or 
These give details or further
information on what has already been said, and
are aimed at preventing damage to the machine
or causing damage.
Non-observance will
result in the risk of injury to oneself or others.
Non-observance will
result in the risk of serious injury or death to
oneself or others.
A)...

4.Replace the exhaust silencers if they are
faulty.
5.Each time the brush cutter is used, a general
check must be carried out on the condition of
the equipment, cutting unit, guards and fasten-
ing elements before switching it on, to ensure
that the parts are not worn, damaged or loose.
Always check that the throttle lever and «STOP»
button work correctly. 
Check that the lever that blocks the throttle
(safety lever) works correctly; the throttle should
only work when the safety lever on the upper
side...

D) MAINTENANCE AND STORAGE
1.
Ensure that all screws and bolts are tightly fas-
tened so that the machine can be used in safety.
Regular maintenance is essential for safety and
a consistently high performance.
2.Do not use the machine if any parts are dam-
aged or worn. These parts must be replaced, not
repaired. Use original spare parts.The cutting
tools must always bear the manufacturer’s mark
as well as the maximum working speed. Spare
parts that are not the same quality may damage
the machine and...

It is not necessary to com-
pletely unscrew the fastener screws Simply
loosen the screws so that it is possible to insert
the handlebar handgrip into the block system. 
Insert the handgrips halves into the handgrip
support checking that the two parts of the hand-
grip have been correctly joined on the handlebar.  
Intervene again on handle A but do not tighten
completely. 
Adjust the position of the handlebar, then tighten
completely until the handgrip locks safely into
place on the handlebar
Never work...

In order to use the brush cutter, clothes must be
worn that protect against objects thrown up by
the tool (e.g. stones). Wear safety shoes with a
slip-proof sole, gloves, safety goggles (the visor
used on its own does not protect the eyes suffi-
ciently), tight-fitting clothes. Do not wear loose-
fitting clothes, scarves, ties, jewellery or other
dangling objects that could get caught on
branches. Long hair must be tied up and pro-
tected. Equipment to protect hearing such as ear
defenders must be worn...