Getnet Router GR-724W User Manual

64 
2-7-1-3 Setup procedure for ‘AP Bridge-Point to Point’: 
 
In this mode, you can connect your wireless router with another, to 
combine two access points and expand the scope of wireless network, and 
all clients (wired only – AP will not accept wireless clients in this mode) 
of two wireless routers will think they’re on the same physical network. 
This function is very convenient when you need to connect two networks 
between two buildings. Here are instructions about how to connect two 
wireless...

65 
 
2-7-1-4 Setup procedure for ‘AP Bridge-Point to Multi-Point’: 
 
In this mode, you can connect your wireless router with at least four 
wireless routers to expand the scope of wireless network, and all clients 
(wired only – AP will not accept wireless clients in this mode) of the 
wireless routers will think they’re on the same physical network. 
 
 
 
 
 
 
 
 
 
 
 
 
Here are descriptions of every setup items: 
 
Band (2):  Select the band you want to use, all the wireless 
routers must use the...

66 
four other access points together, and every access point can still accept 
wireless clients. 
 
 
 
 
 
 
 
Here are descriptions of every setup items: 
Band (2):  Select the band you want to use, all the wireless 
routers must use the same setting. 
 
SSID (3):  Input the SSID of your wireless router, the setting 
should be the same with other wireless routers for 
the convenience of roaming. 
 
Channel  Select the channel you want to use, all the wireless 
Number (4):  routers must use the same...

67 
1 to 4 (6 - 9):   
 
Set Security    Click to set security settings for this connection 
(10):  (Please go to section ‘2-7-3 Wireless Security’ for 
detailed instructions). 
 
 
2-7-1-6 Setup procedure for ‘Universal Repeater’ 
 
In this mode, the router can act as a wireless repeater; it can be Station 
and AP at the same time. It can use Station function to connect to a Root 
AP and use AP function to service all wireless stations within its 
coverage.  
 
 
 
 
 
 
  
Here are descriptions of...

68 
wireless router from others when there are other 
wireless routers in the same area. Default SSID is 
‘default’, it’s recommended to change default ESSID 
value to the one which is meaningful to you, like 
myhome, office_room1, etc. 
 
Channel  Select the channel you want to use, all the wireless 
Number (4):  clients must use the same setting. 
 
Associated Clients (5): Click ‘Show List button, then an “Active Wireless 
Client Table” will pop up. You can see the status of 
all active wireless...

69 
effect (Please wait for about 30 seconds while router is rebooting). 
 
 
2-7-2 Advanced Wireless  Settings 
 
This router provides some advanced control of wireless parameters, if 
you want to configure these settings, please click ‘Wireless’ menu on the 
left of web management interface, then click ‘Advanced Settings’, and 
the following message will be displayed on your web browser: 
 
 
 
Here are descriptions of every setup items: 
 
Fragment  Set the Fragment threshold of wireless radio....

70 
default value is 100. 
 
DTIM Period (4):    Set the DTIM period of wireless radio. Do not 
modify default value if you don’t know what it is, 
default value is 3. 
 
Data Rate (5):    Set the wireless data transfer rate to a certain value. 
Since most of wireless devices will negotiate with 
each other and pick a proper data transfer rate 
automatically, it’s not necessary to change this 
value unless you know what will happen after 
modification. 
 
N Data Rate (6):   Same as above, but only for...

71 
big space, you may not have to set output power to 
100%. This will enhance security (malicious / 
unknown users in distance will not be able to 
reach your wireless router). 
 
WMM (12):    The short of Wi-Fi MultiMedia, it will enhance the 
data transfer performance of multimedia contents 
when they’re being transferred over wireless 
network. If you don’t know what it is / not sure if 
you need it, it’s safe to set this option to ‘Enable’, 
however, default value is ‘Disable’. 
 
After you finish...

72 
 
Please select an encryption method from ‘Encryption’ dropdown menu, 
there are four options: 
 
 
2-7-3-1 Disable wireless security 
 
When you select this mode, data encryption is disabled, and every 
wireless device in proximity will be able to connect your wireless router 
if no other security measure is enabled (like MAC address access control 
- see section 2-7-4, or disable ESSID broadcast).   
 
Only use this option when you really want to allow everyone to use your 
wireless router, and you...

73 
characters of key will be displayed. For example, if 
you select ’64-bit’ as key length, and ‘Hex’ as key 
format, you’ll see the message at the right of ‘Key 
Format’ is ‘Hex (10 characters), which means the 
length of WEP key is 10 characters. 
 
Default Tx Key (4):    You can set up to four sets of WEP key, and you can 
decide which key is being used by default here. If 
you don’t know which one you should use, select 
‘Key 1’. 
 
Encryption Key     Input WEP key characters here, the number of 
1...