Fujitsu F02d Manual

							19
Introduction
~Wireless LAN (WLAN) exchanges information using 
radio waves, and allows you to freely establish LAN 
connection if you are within an area where radio wave 
reaches. On the other side, if you communicate 
without appropriate security settings, 
communications may be intercepted or hacked by 
malicious parties. It is recommended to make 
necessary security settings on your judgement and 
responsibility.
~Wireless LANDo not use Wireless LAN in a place where magnetized 
by electric products, AV, OA equipment, etc. or where 
electromagnetic wave is generated.
- If magnetism or electrostatic noise affects FOMA terminal, noise may be increased or communication 
may not be available (especially when using 
microwave oven, it may affect the terminal).
- Using near TV or radio may cause poor reception or TV  screen may be blurred.
- When multiple wireless LAN access points exist near  FOMA terminal and they use the same channel, search 
may not be performed correctly.
~Frequency bandsFrequency bands for WLAN devices are written on 
battery pack insert section of phone. Label description 
are as follows.
a2.4 : Radio equipment that uses the 2400 MHz band.bDS : The modulation is the DS-SS method.cOF : The modulation is the OFDM method.d4 : The expected interference distance is 40 m or 
shorter.
e : All bandwidths between 2400 MHz 
and 2483.5 MHz are used, and the bandwidth used by 
mobile object identification devices can be avoided.
Available channel varies by countries. To use WLAN 
overseas, check the conditions such as available 
frequency, regulation, etc. for the country. To use in airplane, confirm with airline company in 
advance.
Cautions on using 2.4GHz devicesIn the bandwidth used by WLAN devices, in addition to 
home electric appliances such as a microwave oven and 
industrial/scientific/medical devices, in-plant radio 
stations for identification of mobile objects used in 
production lines of a factory (a license is required), 
specified low power radio stations (a license is not 
required), or amateur radio stations (a license is 
required) can be in operation.
1. Before using this device, confirm that in-plant radio 
stations for identification of mobile objects, specified 
low power radio stations or amateur radio stations 
are not in operation in your neighborhood.
2. If this device generates harmful radio wave 
interference against in-plant radio stations for 
identification of mobile objects, change the using 
frequency promptly or stop using wireless LAN 
function, and contact General Inquiries on the last 
page of this manual, then consult about treatment for 
prevention of the interference (for example, 
installation of partitions etc.).
3. If this device generates harmful radio wave  interference against in-plant radio stations for 
identification of mobile objects or amateur radio 
stations, or if any trouble, contact General Inquiries 
on the last page of this manual.
Wireless LAN (WLAN)
%40
a bc
e d 
						

							20
Introduction
~FeliCa reader/writer function of FOMA terminal uses 
weak waves requiring no licenses for radio stations.
~It uses 13.56 MHz frequency band. When using other 
reader/writers in your surroundings, keep FOMA 
terminal away sufficiently from them. Before using 
the FeliCa reader/writer, confirm that there are no 
radio stations using the same frequency band nearby.
~FM transmitter of FOMA terminal uses weak waves 
requiring no licenses for radio stations.
~It uses 77.4 - 85.0MHz frequency band. To use it, set 
frequency not to common to FM radio station of the 
area you use to avoid affecting FM radio users in 
neighborhood.
~Do not use a remodeled FOMA terminal. Using a 
remodeled terminal violates the Radio Law.
FOMA terminal is certified according to technical 
standard conformance of specified wireless 
equipment based on the Radio Law, and as a proof of 
it, the Technical Compliance Mark   is depicted on 
the engraved sticker of FOMA terminal.
If you remodel FOMA terminal by removing its screws, 
your certification of technical standard conformance 
becomes invalid.
Do not use FOMA terminal with its certification of 
technical standard conformance invalid as it violates 
the Radio Law.
~Be careful when you use FOMA terminal while driving 
a car etc.
Using a mobile phone while driving is subject to penal 
regulations.
However, absolutely necessary cases such as rescue 
of a sick person or maintaining publics safety are 
exempted.
~Use the Bluetooth function only in Japan.The Bluetooth function of the FOMA terminal is 
compliant with wireless standards and is authorized 
for use only in Japan.
If you use this function overseas, you may be 
punished.
~Use FeliCa reader/writer function only in Japan.FeliCa reader/writer function of FOMA terminal 
conforms to Japanese radio standards.
If you use this function overseas, you may be 
punished.
~Use FM transmitter only in Japan.FM transmitter of FOMA terminal is compliant with 
wireless standards and is authorized for use only in 
Japan.
If you use this function overseas, you may be 
punished.
~Do not alter basic software.Repair may be refused due to modification of the 
software.
~There are differences in feeling of stereoscopic effect 
of 3D images among individuals.
~When viewing 3D images, keep the display parallel to 
both eyes.
FeliCa reader/writer
FM transmitter
CAUTION
Viewing 3D images 
						

							21
Introduction
Waterproofness/Dustproofness
F-02D provides waterproofness of IPX5*1, IPX8*2 
and dustproofness of IP5X*3 with firmly closing 
the external connection jack cap and installing 
the back cover in a locked state.
*1IPX5 means that a phone keeps functioning after 
applying a jet flow of 12.5 L/min. from every 
direction from a distance of approximately 3 m for at 
least 3 minutes using water nozzle in 6.3 mm inner 
diameter.
*2For F-02D, IPX8 means that a phone keeps 
functioning after F-02D is slowly submerged to 
depth of 1.5m in static tap water at room 
temperature, left there for 30 minutes and then taken 
out, and the mobile phone keeps shooting still 
images or moving pictures in approximately 30 
minutes in static tap water at room temperature.
*3IP5X means a protection degree that a phone keeps 
functioning and safety after it is placed in a device 
with dust in diameter 75
 or less for 8 hours, 
agitated and then taken out.
✜ What you can do with waterproofness 
of F-02D
~You can talk or watch 1Seg programs without 
using an umbrella in the rain (for rainfall of 20 
mm or less per hour).
- When your hands or FOMA terminal are wet,  avoid installing/removing the back cover or 
opening/closing the external connection jack 
cap.
~You can also shoot still images and moving 
pictures in the pool depth of 1.5 m.
- Do not perform other operations underwater than shooting still images and moving 
pictures.
- If you put the terminal in water of swimming  pool, be sure to have it within 30 minutes. - If FOMA terminal gets wet with water from the 
swimming pool or soak in water of swimming 
pool, wash it in specified procedure (
ðP23).~You can use FOMA terminal in a bathroom.- Do not put the terminal in the bathtub. Do not use the terminal in hot water. May cause 
malfunction.
- Never put FOMA terminal in hot spring water  or water containing soap, detergent or bath 
powder.
To ensure waterproofness/
dustproofness
To avoid water/dust ingress, be sure to observe 
the following points.
~Do not throw any liquid other than room-
temperature tap water on FOMA terminal, or 
soak it in such liquid.
~When using the external/HDMI connection jack, 
put your finger into the groove as shown then 
pull the cap up in the direction of the arrow.
Groove 
						

							22
Introduction
After using the external/HDMI connection jack, 
close the cap as the direction shown in the 
illustration, and make sure that the cap is 
completely closed without slack by pushing the 
tabs in.
~For installing the back cover, see Installing back 
cover of Attaching docomo mini UIM card/
battery pack.
ðP25~Securely lock the back cover and firmly close the 
external connection jack cap. Even a fine 
obstacle (one hair, one grain of sand, tiny fiber, 
etc.) put between contact surfaces may allow 
water to enter.
~Do not poke the microphone, earpiece or 
speaker with a swab or sharp object.
~Do not let FOMA terminal fall. It may become 
scratched causing the waterproof/dustproof 
performance to degrade.
~The external connection jack cap and the rubber 
packing of the rear side of the back cover play an 
important role for keeping waterproof/dustproof 
performance. Do not deform the back cover by 
twisting etc. or peel off or damage the rubber 
packing. Also, prevent dust from adhering to it.
To keep FOMA terminal waterproofness/
dustproofness, replacement of parts is required 
every 2 years regardless of whether FOMA 
terminal appears normal or abnormal. 
DOCOMO replaces the parts as a chargeable 
service. Bring FOMA terminal to a sales outlet 
such as a DOCOMO-specified repair office.
Important precautions
Do not perform actions shown in the illustrations 
below.
Observe the following precautions to use FOMA 
terminal properly.
~Accessories and optional devices are not 
waterproof/dustproof. When watching 1Seg etc. 
with FOMA terminal installed in the included 
desktop holder, do not use it in a bathroom, 
shower room, kitchen or lavatory even if it is not 
connected to the AC adapter.
~Do not apply water flow stronger than allowed (ðP21) (e.g., such water flow that gives you pain 
when applied to your skin directly from a faucet 
or shower). F-02D provides IPX5 waterproof 
performances. However, it causes malfunction.
~If FOMA terminal gets wet with salt water, sea 
water, refreshing beverage or mud or soil 
adhered, wash it immediately. If they dry out, it 
is hard to remove the dirt and it may cause 
damage or malfunction.
~Do not put FOMA terminal in hot water, use it in 
a sauna or apply hot airflow (from a hair dryer 
etc.) to it.

Using Soap/Detergent/
Bath powder
Soaking in
ocean water
Applying strong
 water flowUsing in 
hot spring
Machine-washingWashing with
 brush/sponge 
						

							23
Introduction
~Do not move in water or slam the terminal 
against the surface of water with FOMA terminal 
opened.
~If you put the terminal in tap water or in water of 
swimming pool, be sure to have it within 30 
minutes.
~When you use the terminal in swimming pool, 
obey rules of the facility.
~FOMA terminal does not float on water.~Do not leave water on FOMA terminal. May 
short-circuit the power jacks, or in a cold region, 
water may freeze causing malfunction.
~Do not leave water on the microphone, earpiece 
or speaker. Such water may interfere with 
talking.
~Do not leave water on the temperature/humidity 
sensor. Measuring temperature and humidity 
may not be correct.
~If the back cover is damaged, replace it. Water 
may enter inside from a damaged section 
causing troubles such as electric shocks or 
corrosion of the battery.
~If FOMA terminal gets wet with water or other 
liquids with the external connection jack cap or 
the back cover open, the liquid may get inside 
the terminal causing electric shocks or 
malfunction. Stop using FOMA terminal, turn 
the power OFF, remove the battery pack and 
contact a DOCOMO-specified repair office.
~If the external connection jack cap, or the rubber 
gasket on the rear side of the back cover is 
damaged or deformed, replace it at DOCOMO-
specified repair office.
DOCOMO does not guarantee actual operations 
under all states. Malfunctions deemed to be 
caused by inappropriate operation by the 
customer are not covered by the warranty.
With pressing and holding the external 
connection jack cap not to open, wash the 
terminal in tap water without rubbing hard
~Do not apply water flow stronger than allowed (ðP21) (e.g., such water flow that gives you pain 
when applied to your skin directly from a faucet 
or shower).
~In locked state with the back cover attached, with 
pressing and holding the external connection jack cap 
not to open, wash the terminal in tap water in room 
temperature without rubbing hard.
~Do not use brush, sponge, soap, detergent, etc.~If mud or soil is adhered to the terminal, do not 
open, close or rotate the terminal. Eliminate the 
dirt first by shaking several times in tap water of 
wash-basin and then wash the terminal with 
running water.
~After washing, wipe the surface with dry cloth 
well, drain water by the following procedure and 
let the terminal dry naturally.
Washing FOMA terminal
Press here 
						

							24
Introduction
When FOMA terminal is wet, water may flow out after 
wiping it off; drain the water in the following steps.
aWipe off moisture on the FOMA terminal 
surface and back side with dry, clean cloth etc.
bShake FOMA terminal approximately 20 times, 
firmly holding its hinge section, until there is 
no more water splattering.
cPress lightly FOMA terminal against dry, clean 
cloth etc. to wipe off water remaining in the 
microphone, earpiece, speaker, keypad, hinges 
or charging jack, etc.
dWipe off water drained from FOMA terminal 
with dry, clean cloth etc., and dry naturally.

KWater, if any, remaining in FOMA terminal 
may ooze up after wiping off.

KDo not wipe off water remaining in gaps 
directly with a cotton swab etc.
Check the following before and after charging.~Check if FOMA terminal is not wet. Never try to charge 
the battery pack when FOMA terminal is wet.
~Accessories and optional devices are not 
waterproof/dustproof.
~When charging the battery when or after FOMA 
terminal is wet, adequately drain it and wipe off 
water with a dry, clean cloth etc., before 
connecting the accessory desktop holder or 
opening the external connection jack cap.
~When the external connection jack cap is opened 
for charging, close the cap firmly after charging. It 
is recommended to use the desktop holder for 
charging to prevent water from seeping inside 
from the external connection jack.
~Do not use the AC adapter or desktop holder in 
a bathroom, shower room, kitchen, lavatory or 
other highly humid area. May cause fire or 
electric shock.
~Do not touch the AC adapter or desktop holder 
with wet hands. May cause electric shock.
Draining water from FOMA 
terminal
Swing the FOMA terminal with the 
speaker above to drain water off
Charging 
						

							25
Basic Operation
Before Using
Attaching docomo mini UIM card/battery pack
After turning power OFF, close FOMA terminal 
and hold it in your hand so that you can properly 
attach docomo mini UIM card/battery pack.
✜ Removing back cover
✜ Attaching docomo mini UIM card
Point
KOnly docomo mini UIM card is available for the 
FOMA terminal. If you have a UIM or FOMA card, 
bring it to docomo Shop to replace.
✜ Installing battery pack
✜ Installing back cover
Point
KMake sure the locations of the slots for docomo mini 
UIM card and microSD card. If the cards cannot be 
removed, bring the FOMA terminal to a docomo 
Shop.
b Press and slide the back cover 
in the arrow direction approx. 
2 mm to remove
a Slide the lever in the direction a to unlock
Back cover
With facing IC side of the docomo mini UIM card down, 
insert to the slot slowly and push it until it clicks
IC Corner cut
docomo mini UIM card
With the label side up, fit the
convex parts to the concave 
parts of the FOMA terminal 
and insert in the 
a direction, 
then push in the b direction
to set in. Convex parts
Concave parts
a a b
cb Slide the lever in the direction c 
to lock
a Fit the 8 tabs to the notches of the 
FOMA terminal and push in the 
direction 
a not forming any 
clearance, then slide in the 
direction 
b. 
						

							26
Basic Operation
Before Using
Charging
The battery pack does not have a full charge at time of purchase. Use AC adapter for FOMA terminal to 
charge the battery before using FOMA terminal.
aInsert the connector of AC adapter 
horizontally to the accessory desktop 
holder, with the arrows mark side 
upward
bUnfold the power plug and insert it into 
a 100V AC outlet
cClose FOMA terminal and insert it into 
the desktop holder
dCheck that the charging light turns on*After charging is completed, remove FOMA 
terminal from the desktop holder.
aOpen the external connection jack cap 
(a), hold the connector horizontally 
with the arrows side upward and insert 
it to the jack (
b)
bUnfold the power plug  and insert it into 
a 100V AC outlet
cCheck that the charging light turns on*When charging is over, pull out the power plug from 
the outlet, and pull out from FOMA terminal 
horizontally while pressing the release buttons on 
both sides of the connector.
Charging using desktop holder
Charging using AC adapter
AC 10 0V 
outlet
Release 
buttons
Connector
Desktop HolderAC adapter
a 
c 
b 
d 
a 
AC 100V 
outlet
Connector
Release 
buttons
External 
connection jack External connection jack cap
AC adapter
c b  
						

							27
Basic Operation
Before Using
Power ON - Default setting
Initial setting is an operation when FOMA terminal 
is turned ON for the first time.
af (2 sec. or more)The Initial setting screen appears.
bSet required itemseC [Complete]If you exit without setting Change security 
code and Request permit/deny., Initial setting 
screen reappears when the power is turned 
ON the next time.
cOn a confirmation screen of software 
update function, g eOn the 
confirmation screen of Error info send 
set., 
gThe stand-by display appears.
When a Machi-chara asks your name (user 
name), press 
g twice to enter a user name.
Point
KIf no operation is performed, the display light is 
automatically turned off according to the settings in 
Light time-out or eco mode  setting. The display light 
turns on again if there is any operation or incoming 
call.

KThe battery usage state is automatically recorded 
while using the FOMA terminal. The record is used 
only for repair diagnosis.
Turning power off : f (2 sec. or more)Changing the initial setting : m ehibChanging screen display to English : m ehddeSelect English
Before Using
Caller ID notification
Set whether to notify your phone number (caller 
ID) to the other partys terminal when making a 
voice call.
a m eg TEL functioned Dial/
Receive call setting
e c Caller ID 
notificatione b Settingea ON  or b 
OFF
Point
KIf you hear an announcement of requesting caller ID 
when making a call, set Caller ID notification or add 
prefix 186 to the phone number to call again.
Before Using
Checking Profile
Check a model name or own phone number.
a m e0 ProfileUser information screen appears.
PointEditing the profile : On User information screen, C
eAuthenticateeSet required itemse C
KOn the profile edit screen, select first mail address 
then select Acquire Auto to obtain your mail 
address from the i-mode center. For details of 
changing a mail address, refer to Mobile Phone 
Users Guide [i-mode] FOMA version.
Checking a phone number during a call : s e0 
						

							28
Basic Operation
Screen Explanation
Viewing display
New arrival information and current state can be 
checked by the icon appearing on the screen. 
Major icons are as follows.a Status areaStatus icons are displayed. Select an area to 
display the status menu.ðP30
Battery level (Battery icon)
Signal strength (Antenna icon)
 : Self mode ON : In data transfer mode : Connecting to i-mode : Display off lock setting in Auto-key lock is set : Infrared communication in operation : Bluetooth ON : The total calls cost exceeds the limit : Communication using handsfree-compatible 
device in progress
 : Handsfree ON : Femtocell available : Touch operation OFF : Positioning with GPS : Location request setting : Connecting to Wi-Fi : Unread Area Mail exists : In-area auto-send mail exists : Unread i-mode mail exists : Arrival i-concier information exists : Unreceived i-mode mail exists in the Center
b
c
de
h
g
f
a
a
X”‡œ(Kuman)©Dora communications
Ample
chargeAlmost exhausted
(Charge the battery)
StrongOut of service area or where
radio waves do not reachWe a k