Fujitsu F02d Manual

							21
❖Setting for Windows XP
1Click µ»”Ä (Start) àSelect  b‚owÓé¬åÜ (All programs) àž«
·±æ (Accessories) àè	ô (Communication) and click  	ý`M
€¢Ÿ
²”Å (New connection wizard).
2On the   (Start new connection wizard start) 
screen, click   (Next).
3Select  ï»”É¿Ät
€b” (Connect to Internet) and click    
(Next).
4Select  
€›	ˆp·¿Äž¿Ób” (Set up connection manually) and 
click   (Next).
5Select  ¼ àçž¿ÓÞÃÜ›–;`o
€b” (Use dialup modem to 
connect) and click   (Next).
When 
						

							22
8Enter ┲”Ê (User name) àEnter  ͵ë”Å (Password) àEnter  ͵
ë”Åw¬ÝÖ— (Password confirmation entry) àSelect all items as shown 
below and click   (Next).

KIn ┲”Ê (User name) and  ͵ë”Å 
(Password), enter the user name and password 
specified by your provider or network 
administrator.

KWhen the access point is mopera U or mopera, 
you do not need to enter  ┲”Ê (User 
name),  굑Ӂ (Password) or  굑Ӂ
w¬ÝÖ—  (Password confirmation entry).
9On the 	ý`M
€¢Ÿ²”Åwìƒ (New connection wi zard is completed) 
screen, click  ìƒ (Done).
10Click µ»”Ä (Start) àSelect  b‚owÓé¬åÜ (All programs) àž«
·±æ (Accessories) àè	ô (Communication) and click  É¿Ä딫
€ 
(Network connection).
11Select the created dialup connection icon and click   (File)àClick  
ÓéÍŸ (Property).
12Confirm the setting of each item in  
¶
` (General) tab.

KWhen plural modems are connected to a PC, set 
as follows.
For USB cable connection : Select only  ÞÃÜ-
FOMA F02D (Modem-FOMA F02D) at  

						

							23
13Click É¿Ä딫 (Network) tab àSet each item as shown below àClick 

ƒ (Settings).

KWhen settings of IP and DNS information have 
been requested from the provider, etc. select   
ﻔɿÄÓéįç (TCP/IP) (Internet 
protocol (TCP/IP)), click  ÓéÍŸ (Property) 
and set necessary information.

KSince QoS Í­¿Äµ­´á”å (QoS packet 
scheduler) settings in  \w

						

							24
4Enter ┲”Ê (User name) àEnter  ͵ë”Å (Password) àClick  ¼ 
àç (Dial).

KIn  ┲”Ê (User name) and  ͵ë”Å 
(Password), enter the user name and password 
specified by your provider or network 
administrator.

KWhen using mopera U or mopera, you do not 
need to enter  ┲”Ê (User name) or  ͵
ë”Å (Password).

KWhen  ┲”Ê (User name) was entered or 
굑Ӂ (Password) was saved while settings, 
these entries are no longer necessary.

KClick OK when the connection established 
screen is displayed.
✔ INFORMATION

KFOMA terminal displays a connecting screen when you execute packet communication or 64K data 
communication. The following screens are displayed when a connection has been established.

KThe communication speed displayed on your PC may differ from actual speed.
KThe communication is available only with FOMA terminal that was connected when the dialup network was set.
❖Disconnecting communication
Just exiting the PC browser may not disconnect co mmunication. To ensure disconnection, perform the 
following operation.
 Under Windows 7
1Click   on the task tray àConnection name to disconnect à
~… 
(Disconnect).
Under Windows Vista
Right-click   in the task tray àSelect  
~… (Disconnect) and click the dialup connection to 
disconnect.
Under Windows XP
Click dial-up icon in the task tray àClick  
~… (Disconnect).
For 64K data 
communication
For packet 
communication 
						

							25
Connecting to a Wi-Fi compatible PC
Even out of public wireless LAN area, you can perform packet communication with 
connecting a Wi-Fi compatible PC to use FOMA terminal as an access point.

K
Switch FOMA terminal to AP mode ON in advance. For AP mode settings, refer to Instruction manual 
(detailed version) (in Japanese only) (PDF file) of the FOMA terminal.
 Under Windows 7
1Click  (Start) à¯ïÄé”çÍÉç (Control panel) àÉ¿Ä딫w	Ý6
q»µ«w
¯Ô (Network status and tasks) in the  É¿Ä딫q ï»”
É¿Ä (Network and Internet) category.
Under Windows Vista
Click  (Start) à
€
Π(Dialup connection).
2Click  	ý`M
€‡hxÉ¿Ä딫w·¿Äž¿Ó (Setup new connection 
or network).
Under Windows Vista
Click  
€‡hxÉ¿Ä딫›·¿Äž¿Ó`‡b  (Set up connection or network).
3Select ë àèµÉ¿Ä딫t	ˆp
€`‡b (Connect to Wireless 
network manually) and click   (Next).

KTo make wireless connection for the first time, on the  ë àèµÉ¿Ä딫t	ˆp
€`‡b 
(Connect to wireless network manually) screen, change  ë à赞¼Ó» (Wireless adapter) to 
 ë àèµÉ¿Ä딫
€ (Wireless network connection) and click   (Next).
4Enter network information and click  (Next).

KSet it to the same as  Á
¢
ƒ (Wireless settings) of the FOMA terminal.
- É¿Äë”«Ê (Network name) : Enter the SSID set for the FOMA terminal.
- ·©áæŸw	¨ (Security type),  ‰ø=w	¨ (Encryption type) : Set  Ý	ÂMÜ 
(Authentication method) information in the FOMA terminal. In  Ý	ÂMÜ (Authentication 
method), it is described in the format combining  ·©áæŸw	¨ (Security type) and  ‰
ø=w	¨  (Encryption type) settings. Select a corresponding setting.  Í”¹Æç (Personal) 
in  ·©áæŸw	¨  (Security type) is the same meaning as PSK.
- ·©á柩”  (Security key) (For Windows Vista,  ·©á柩”‡hx͵Ñ蔶 
(Security key or pass phrase) : Enter encryption key (WEP or PSK).
5Click  a” (Close).
ÙTo re-execute communication via Wi-Fi connection after disconnectionUnder Windows 7
 (Start) à¯ïÄé”çÍÉç (Control panel) àÉ¿Ä딫w	Ý6q»µ«w
¯Ô  (Network status 
and tasks) in the  É¿Ä딫q ï»”É¿Ä  (Network and Internet) category àOn the  É¿Äë”
«qž·ï»” (Network and sharing center) screen,  
						

							26
AT command
AT commands are commands for setting FOMA terminal functions using a PC. FOMA 
terminals comply with AT commands and support some extended commands and 
proprietary AT commands.
❖AT command input format
AT must be entered before each AT command. Commands must be entered in one-byte alphanumeric 
characters.
 Connecting to mopera U with ATD command
AT commands and their parameters must be entered on a single line. All the characters from the first 
character until the character directly preceding   must  be entered on a single line. Each line can be up to 
256 characters including AT.
❖AT command input mode
To operate FOMA terminal using AT commands, a PC mu st be in terminal mode. Terminal mode is a mode 
that lets the PC operate as a single communication te rminal. When terminal mode is set, the characters 
entered from the keyboard are sent directly to  the communication port to operate FOMA terminal.

KOffline mode
FOMA terminal is in stand-by. FOMA terminal must be  in stand-by status to use AT commands to control 
it.

KOnline data mode
FOMA terminal is communicating. If you enter AT commands when FOMA terminal is performing 
communication, the sent characters are sent direct ly to the communication receiver and may cause the 
receivers modem to malfunction. Do not enter  AT commands while FOMA terminal is performing 
communication.

KOnline command mode
AT commands can be used even when FOMA terminal is in communication mode. These operations 
make it possible to execute AT commands without in terfering with the connection to the communication 
receiver, and normal communication can continue after the commands have finished executing.
Switching between online data  mode and online command mode
To switch FOMA terminal from online data mode  to online command mode, you can use either of the 
following procedures.

KEnter +++ command or code set in the S2 register.
KTurn the RS-232C*ER signal OFF when set in AT&D1.
* The USB or Bluetooth interface emulates an RS-232C signa l line so RS-232C signal control using communication 
applications is possible.
To switch from online command mode to online data mode, enter ATO .
✔ INFORMATION

KWhen making a call or sending an AT command from external device, it is sent from Number A with 2in1 in Dual 
mode or A mode, and from Number B in B mode.
ATD Î99ÎÎÎ3 
Return character : Press Enter key. (Command separator)
Parameter : Commands argument
Command : Command name 
						

							27
×List of AT command

KThe followings are AT command that can be used via the FOMA F02D (Modem).
KEntering  Ç may cause \ to appear depending on the font setting for a PC or communication software.
KIf the battery pack is removed from FOMA terminal be fore the terminal power is turned off, the setting 
values may not be recorded.
Upper slot : Command Lower slot : ExampleDescription
A/ Execute the previously executed command again.
When previous response is ERROR, ERROR is returned.
A/
OK
AT Use commands on this list by prefixing to co mmands other than A/ or +++. When using only 
this command, OK is returned with FOMA terminal enabled for using AT commands.
AT
OK
ATA Perform the receiving process when entere d while receiving a packet communication or 
64K data communication.
The following commands can be entere d when receiving a packet communication.
ATA184 : Handling of incoming calls : Send caller ID function OFF
ATA186 : Handling of incoming calls : Send caller ID function ON
RING
ATA
CONNECT
ATD
ATDÎ99 ÎÎÎ # : Performs calling pr ocess for packet communication.
If  or  ÎÎÎ is omitted, =1 is set.
ATD [parameter] [phone number] : Perform calling process for 64K data communication.
Calling process is not permit ted if phone number contains characters other than the 
following.
0-9,  Î, #, A, a, B, b, C, c
The following characters and a space can be  entered but are not recognized in dialing.
,(comma), !, -, @, D, d, P, p, T, t, W, w
Setting Show/Hide caller ID is enabled by inserting 186 or 184 after ATD.
ATDN or ATDL can be used for redial calling.
ATD
Î99 ÎÎÎ 1#
CONNECT 460800
ATE
*1Set whether FOMA terminal will retu rn echo for command sent from a PC.
n=0 : Echo OFF yyn=1 : Echo ON (default)
Normal usage is n=1. If the PC has an echo  function, setting this command to n=0 prevents 
double display of characters.
ATE1
OK
ATH
Disconnect line when entered during a communication.
Execute in online command mode. àP26
ATH
NO CARRIER
ATI Display the confirmation code.
n=0 : NTT DoCoMoyyn=1 : Display model name of FOMA terminal
n=2 : Display version of FOMA terminal yyn=3 : Display elements of ACMP signals
n=4 : Display details of functi ons that can be communicated  by FOMA terminal in numeric
ATI0
NTT DoCoMo
OK
ATO
Return from online command mode to  online data mode during communication.
ATO
CONNECT 460800
ATQ
*1Set whether to display result code.
n=0 : Display (default) yyn=1 : Not display
When ATQ1 is executed, OK is not returned.
ATQ0
OK
ATS0=
*1Set number of rings until FOMA terminal receives communication automatically.
n=0 : Not receive automatically (default)
n=1-255 : Receive automatically with specified number of rings
ATS0? : Display current settings
ATS0=0
OK
ATS2=
Set escape character.
n=0-127 (default : n=43)yyWhen n=127 is set, escape is unavailable.
ATS2? : Display current settings
ATS2=43
OK
ATS3=
Set the carriage return (CR) character that  identifies the end of AT command character 
string. Appended to end of echoed command character string and result code.
n=13 (fixed value)
ATS3? : Display current settings
ATS3=13
OK 
						

							28
ATS4=Set the line feed (LF) character. When result  code is displayed as alphabetic characters, 
appends the character after the carriage return (CR) character.
n=10 (fixed value)
ATS4? : Display current settings
ATS4=10
OK
ATS5=
Set the back space (BS) character. When this  character is detected during command input, 
the last character in the input buffer is deleted.
n=8 (fixed value)
ATS5? : Display current settings
ATS5=8
OK
ATS6=
Set pause time (seconds) until dia ling commences but do not operate.
n=2-10 (default : n=5)
ATS6? : Display current settings
ATS6=5
OK
ATS8=
Set pause time (seconds) until commas are dialed but do not operate.
n=0-255 (default : n=3)
ATS8? : Display current settings
ATS8=3
OK
ATS10=
*1Set the delay time (1/10 seconds) for au
tomatic disconnection but do not operate.
n=1-255 (default : n=1)
ATS10? : Display current settings
ATS10=1
OK
ATS30=
Set a period of time (minutes) with no da ta transmission/reception to terminate the 
connection for 64K da ta communications.
n=0-255 : (default : n=0, n=0 indicates that inactive timer is set to OFF.)
ATS30? : Display current settings
ATS30=0
OK
ATS103=
Set the separator of received sub addresses fo r 64K data communication.
n=0 :  Îyyn=1 : / (default) yyn=2 :  Ç or \
ATS103? : Display current settings
ATS103=1
OK
ATS104=
Set the separator of sent sub addresses for 64K data communication.
n=0 : # yyn=1 : % (default) yyn=2 : &
ATS104? : Display current settings
ATS104=1
OK
ATV
*1Set result code
 display method.
n=0 : Number displayyyn=1 : Alphabetical display (default)
When ATV0 is executed, 0 is not returned to the same line.
ATV1
OK
ATX
*1Set whether to detect busy 
or dial tones and whether to  display the speed in the 
CONNECT display for the connection.
Busy tone detection : Send BUSY response when dialup connection is busy.
Dial tone detection : Detect whet her FOMA terminal is connected.
n=0 : No busy tone, no dial tone de tected, and no speed is displayed
n=1 : No busy tone, no dial tone  detected, and speed is displayed
n=2 : No busy tone, dial tone de tected, and speed is displayed
n=3 : Busy tone detected, no dial t one detected, and speed is displayed
n=4 : Busy tone detected, dial tone de tected, and speed is displayed (default)
When n=0 is set, AT&E and AT ÇV command will be unavailable.
ATX4
OK
ATZ
*3Reset the current setting to the registered state.
When this command is executed during communica
tion, the terminal is reset after the line 
is disconnected (displaying NO CARRIER).
ATZ
OK (When in offline mode)
AT%V
Display FOMA terminal version.
AT%V
Ver1.00
OK
AT&C
*1Set the operating conditions of  the circuit CD (DCD) for DTE.
n=0 : Always ONyyn=1 : Vary according to line  connection status (default)
When set to n=0, the CD signal is set to  ON directly before sending CONNECT when 
ending connection. The CD signa l is set to OFF directly before the line is disconnected and 
NO CARRIER is sent.
AT&C1
OK
AT&D
*1Set the operation performed when 
circuit ER (DTR) signal received from DTE is switched 
from ON to OFF while online data mode takes effect.
n=0 : Ignore status (status is  always considered to be ON)
n=1 : Move to online command mode wh en status changes from ON to OFF
n=2 : Disconnect line and move to offline m ode when status changes from ON to OFF 
(default)
AT&D2
OK
Upper slot : Command
Lower slot : ExampleDescription 
						

							29
AT&E*1Set the speed display used when connection is made.
n=0 : Display communicati on speed of wireless zone
n=1 : Display communication speed between a PC and FOMA terminal (default)
AT&E1
OK
AT&F
Reset the current setting to the default.
When this command is executed during communica tion, the terminal is reset after the line 
is disconnected (displaying NO CARRIER).
AT&F
OK (When in offline mode)
AT&S
*1Set control of the data set ready 
(DR) signal to be output to DTE.
n=0 : Always ON (default) yyn=1 : ON at time of connection
AT&S0
OK
AT&W Register the current settings in FOMA terminal.
AT&W
OK
AT ÎDANTE Indicate FOMA terminal reception level in the  ÎDANTE :  format.
n=0 : Out of service areayyn=1 : Received signal level of FOMA terminal is 0 or 1 antenna.
n=2 : Received signal level of FOMA terminal is 2 antennas.
n=3 : Received signal level of FOMA terminal is 3 antennas.
AT ÎDANTE=? : Display a list of displayable values
AT
ÎDANTE
Î DANTE : 3
OK
AT ÎDGANSM=
*2Set to reject or permit  incoming packet communications.
n=0 : Reject setting = OFF, A ccept setting = OFF (default)
n=1 : Reject setting=ON yyn=2 : Accept setting=ON
AT ÎDGANSM? : Display current settings
AT ÎDGANSM=? : Display a list of assignable values
AT
ÎDGANSM=0
OK
AT ÎDGAPL= [,]
*2Set the dialup connections (A PN) to permit incoming packe t communications. APN uses 
 defined by +CGDCONT command.
n=0 : Add to list of APN perm itted for incoming communications
n=1 : Delete from list of APN pe rmitted for incoming communications
If the  is not defined by the +CGDCONT co mmand, it can still be added to/deleted from 
the list.
If the  is omitted, all the  are added to/deleted from the list.
AT ÎDGAPL? : Display current settings
AT ÎDGAPL=? : Display a list of assignable values
AT
ÎDGAPL=0,1
OK
AT ÎDGARL= [,]
*2Set the dialup connections (A PN) to refuse incoming packet communications. APN uses 
 defined by +CGDCONT command.
n=0 : Add to list of APN rejected for incoming communications
n=1 : Delete from list of APN re jected for incoming communications
If the  is not defined by the +CGDCONT co mmand, it can still be added to/deleted from 
the list.
If the  is omitted, all the  are added to/deleted from the list.
AT ÎDGARL? : Display current settings
AT ÎDGARL=? : Display a list of assignable values
AT
ÎDGARL=0,1
OK
AT ÎDGPIR=
*2Set Caller ID notification when packet comm unication connection is being performed. This 
command is available when a comm unication is sent or received.
n=0 : Connect to APN directly (default)yyn=1 : Connect to APN prefixing 184
n=2 : Connect to APN prefixing 186
When Show/Hide caller ID is  specified by dialup networkàP17
AT ÎDGPIR? : Display current settings
AT ÎDGPIR=? : Display a list of assignable values
AT
ÎDGPIR=0
OK
AT ÎDRPW Indicate an index for the rece
ption power of the radio waves  that FOMA terminal receive.
AT ÎDRPW=? : Display a list of displayable values
AT ÎDRPW
Î DRPW : 0
OK
AT+CAOC Display last call cost.
AT+CAOC
+CAOC : 000024
OK
AT+CBC Display FOMA terminals battery level in the +CBC : , format.
bcs=0 : Powered by the battery packyybcs=1 : Not powered by the battery pack
bcs=2 : Battery pack removed yybcs=3 : Power-supply error
bcl=0 : No battery remain ed or battery pack removed yybcl=1-100 : Battery remained
AT+CBC=? : Display a list of displayable values
AT+CBC
+CBC : 0,100
OK
Upper slot : Command
Lower slot : ExampleDescription 
						

							30
AT+CBST=,1,0*1Set the line to use (Setting of bearer service)
n=116 : 64K data communication (default)yyn=134 : 64K videophone
AT+CBST? : Display current settings yyAT+CBST=? : Display a list of assignable values
AT+CBST=116,1,0
OK
AT+CDIP=
*1Set to notify/not to notify the sub address 
when receiving in packet communication or 64 
data communication. And, subscription stat us of Multi Number can be confirmed.
n=0 : The information of sub addr ess is not displayed. (default)
n=1 : The information of sub address is displayed.
m=0 : Multi Number not subscribed. yym=1 : Multi Number subscribed.
AT+CDIP? : Display the current settings  and status in the +CDIP:, format
AT+CDIP=? : List of the settable values is displayed.
AT+CDIP=0
OK
AT+CEER
Display the reason of immediate disconnection.
Disconnection reason listàP32
AT+CEER
+CEER : 36
OK
AT+CGDCONT
*2Set dialup connection (APN) for packet communication. àP33
à P33
AT+CGEQMIN
*2Set the criteria for judging whether to permit  QoS (Quality of Service) provisioned by the 
network when packet comm unication is established.àP34
à P34
AT+CGEQREQ
*2Set QoS (Quality of Service) requested to  the network at the transmission of packet 
communication. àP34
à P34
AT+CGMR Display FOMA terminal version.
AT+CGMR
1234567890123456
OK
AT+CGREG=
*1Set whether to report network servic e registration status (Within/Out).
n=0 : Not notified (default)
n=1 : When the terminal is moved from Within service area to Out of service area or vice 
versa, the status is reported in the +CGREG :  format.
stat=0 : Out of packet service area yystat=1 : Within packet service area
stat=4 : Unknown
stat=5 : Within packet service ar ea (during international roaming)
AT+CGREG? : Display the current  settings and status in the +CGREG : , format
AT+CGREG=? : Display a list of assignable values
AT+CGREG=0
OK
AT+CGSN
Display FOMA terminal serial No.
AT+CGSN
123456789012345
OK
AT+CLIP=
*1Set whether to display senders caller ID on  a PC when receiving 64K data communication.
n=0 : Not display result (default) yyn=1 : Display result
m=0 : Network setting not to send caller ID
m=1 : Network setting to send caller ID yym=2 : Unknown
AT+CLIP? : Display the current  settings and status in the +CLIP : , format
AT+CLIP=? : Display a list of assignable values
AT+CLIP=0
OK
AT+CLIR=
*2Set Caller ID notification when
 sending 64K data communication.
n=0 : Use the setting in Caller ID notification of FOMA terminal yyn=1 : Not send
n=2 : Send (default)
m=0 : CLIR not operating (always sends) yym=1 : CLIR operating (never sends)
m=2 : Unknownyym=3 : CLIR temporary mode (default=does not send)
m=4 : CLIR temporary mode (default=sends)
AT+CLIR? : Display the current settings a nd status in the +CLIR : , format
AT+CLIR=? : Display a list of assignable values
AT+CLIR=2
OK
AT+CMEE=
*1Set whether to display an error report at FOMA terminal.
n=0 : Display ERROR and 
no result code (default)
n=1 : Use result code, di splaying reason as number
n=2 : Use result code, displayi ng reason as alphabetic characters
Display reasons in the +CME ERROR : xxxx fo rmat when n=1 or n=2 is set (xxxx = number 
or alphabetic characters). àP33 Error messages list
AT+CMEE? : Display current settings yyAT+CMEE=? : Display a list of assignable values
AT+CMEE=0
OK
Upper slot : Command
Lower slot : ExampleDescription