Fujitsu F02d Manual

							31
AT+CNUMDisplay FOMA terminals own phone number in the +CNUM :  ,, format.
number : Own phone number (With  2in1, display Number B in B mode or Number A in 
other mode)
type=129 : International a ccess code + not included
type=145 : International  access code + included
AT+CNUM
+CNUM : ,090XXXXXXXX,
129
OK
AT+COPS=,2,

*2Set search method for network operator to connect.
n=0 : Auto (default)
yyn=1 : Manualyyn=3 : No mapping
When n=1 is set, set PLMN Number  in hexadecimal value for .
AT+COPS? : Display current settings yyAT+COPS=? : Display a list of assignable values
AT+COPS=0
OK
AT+CPAS
Display whether FOMA terminal can send and receive AT commands to external devices in 
+CPAS :  format.
n=0 : Possibleyyn=1 : Impossible yyn=2 : Status unknown
n=3 : Possible  and receiving
n=4 : Possible and communicating
AT+CPAS=? : Display a list of displayable values
AT+CPAS
+CPAS : 0
OK
AT+CPIN=,

Enter these commands for entering PIN1/PIN2 codes or PUK with PIN1 code ON. To enter 
PUK, enter new PIN1/PIN2 code in . Ev
en if entering in  when entry of 
PIN1/PIN2 code is request, P IN1/PIN2 code cannot be changed.
n=READY : Entry of code not requested yyn=SIM PIN : Entry of PIN1 code waited
n=SIM PIN2 : Entry of PIN2 code waited
n=SIM PUK : Entry of PUK waited due  to failure in unblocking PIN1 code
n=SIM PUK2 : Entry of PUK waited due to failure in unblocking PIN2 code
AT+CPIN? : Display the code currently  requested in +CPIN :  format
AT+CPIN=0000
OK
AT+CR=
*1Set whether to display the communication ty
pe before CONNECT is displayed during 
connection.
n=0 : Not display (default)
n=1 : Display the communication type in the +CR :  format
serv=GPRS : Packet communication yyserv=SYNC : 64K data communication
serv=AV64K : 64K videophone
AT+CR? : Display current settings yyAT+CR=? : Display a list of assignable values
AT+CR=0
OK
AT+CRC=
*1Set whether to use +CRING result codes when communication is received.
n=0 : Not use (default)
n=1 : Use +CRING :  result codes
type=GPRS PPP,,,
 : Packet communication
type=SYNC : 64K data communication
type=AV64K : 64K videophone
AT+CRC? : Display current settings yyAT+CRC=? : Display a list of assignable values
AT+CRC=0
OK
AT+CREG=
*1Set whether to report network servic
e registration status (Within/Out).
n=0 : Not notified (default)
n=1 : When the terminal is moved from Within service area to Out of service area or vice 
versa, the status is reported in the +CREG :  format.
stat=0 : Out of sound service area yystat=1 : Within sound service area
stat=4 : Unknown
stat=5 : Within sound service area  (during international roaming)
AT+CREG? : Display the current settings and status in the +CREG : , format
AT+CREG=? : Display a list of assignable values
AT+CREG=0
OK
AT+CUSD=,
*1Set Additional service (Register USSD) of Ne
twork Services. Enter Service code provided 
by DOCOMO in .
n=0 : Not answer mid result (default)
n=1 : Answer mid result in + CUSD : , ,0 format
m=0 : Information not requested yym=1 : Information requested
AT+CUSD? : Display current settings yyAT+CUSD=? : Display a list of assignable values
AT+CUSD=0,012345678
OK
AT+FCLASS=
*1Set communication type supported by FOMA terminal.
n=0 : Only data s
upported (fixed value)
AT+FCLASS? : Display current settings
AT+FCLASS=? : Display a list of assignable values
AT+FCLASS=0
OK
AT+GCAP
Display the range of AT commands supported by  FOMA terminal in the +GCAP :  
format.
n=+CGSM : Support GSM commands (inc luding the case for supporting a part)
n=+FCLASS : Support +FCLASS commands yyn=+W : Support +W commands
AT+GCAP
+GCAP : +CGSM,+FCLASS,
+W
OK
Upper slot : Command
Lower slot : ExampleDescription 
						

							32
*1Registered in FOMA terminal by &W command.
*2 Not reset by &F and Z commands.
*3 When Z command is executed before the &W command, the terminal  is reset to the last status registered in memory, and 
prior changes are erased.
× Disconnection reason list
Ù Packet communication
AT+GMI Display FOMA terminal manufacturer name.
AT+GMI
FUJITSU
OK
AT+GMM Display model name of FOMA terminal.
AT+GMM
FOMA F02D
OK
AT+GMR Display FOMA terminal version.
AT+GMR
Ver1.00
OK
AT+IFC=
*1Set how to control local flow be tween a PC and FOMA terminal.
n, m=0 : No flow control yyn, m=1 : Perform XON/XOFF flow control
n, m=2 : RS/CS (RTS/CTS) Perform flow control (default)
AT+IFC? : Display the current settings and stat us in the +IFC : , format (n is the 
value of DCE by DTE, and m  is the value of DTE by DCE)
AT+IFC=? : List of the settable values is displayed
AT+IFC=2,2
OK
AT+WS46=
*1Display wireless network used when
 sending communication in n number.
When entering AT+WS46=, ERROR is re turned because it cannot be changed.
n=12 : GSM network yyn=22 : 3G network (FOMA)
n=25 : GSM or 3G network (FOMA) (fixed value)
AT+WS46? : Display current settings yyAT+WS46=? : Display a list of assignable values
AT ÇS Display the currently set commands and S register settings.
AT ÇS
E1 Q0 V1 X4 &C1 &D2 
&S0 ~~~  (snip) ~~~
S104=001
OK
AT ÇV
*1Set whether to use expanded result  codes when connection is made.
n=0 : Not use expanded  result codes (default)
n=1 : Use expande d result codes
AT
ÇV0
OK
+++ Move from online data mode to online command mode when entered during a 
communication.
The escape guard interval is 1 second (fixed value).
+++ (not displayed)
OK
ValueDescription
26 APN is not present or is incorrect.
27
30 Disconnected by network.
33 Terminal does not subscribe to packet communication.
36 Normal disconnection.
Upper slot : Command Lower slot : ExampleDescription 
						

							33
Ù64K data communication
×Error messages list
×Supplement to AT command

K is the number used to control dialup connection (APN) for packet communication to be registered 
in FOMA terminal. 1-10 can be registered in FOMA terminal.

KBy default, the following APNs are registered in cid1-4.
cid1 : mopera.ne.jp (A PN mopera, PPP connection)
cid2 : mopera.net (APN  mopera U, PPP connection)
cid3 : mopera.net (APN  mopera U, IP connection)
cid4 : mpr.ex-pkt.net (APN mopera  U, PPP connection, 128K communication)

K is an optional string for each connection to indicate dialup connection.
ÙCommand name : +CGDCONT=[parameter]

KOutline
Set dialup connection (APN) for packet communication.

KFormat
+CGDCONT= [ [, [,] ] ]

KParameter description
 : 1-10
 : IP or PPP
 : Optional

KExample of execution
The command used to register an APN named abc for PPP connection (when =5).
AT+CGDCONT=5,PPP,abc
OK

KOperation performed when parameter is omitted
AT+CGDCONT= : Return all  to the setting by default.
AT+CGDCONT= : Return the specified  to the setting by default.
AT+CGDCONT? : Display current settings.
AT+CGDCONT=? : Display a list of assignable values.
ValueDescription
1 Specified number does not exist.
16 Normal disconnection.
17 Communication is impossible because remote device is busy.
18 You made a call but did not receive a response within the specified time.
19 The remote device is called but no response.
21 The remote device rejected incoming calls.
63 The service and option of the network are not valid.
65 Unavailable processing speed was specified.
88 You made a call to a terminal or received a call from a terminal with different terminal  properties.
No.Text displayDescription
10 SIM not inserted UIM is not set.
15 SIM wrong Other than DOCOMO SIM (IC card equivalent to UIM) is inserted.
16 incorrect password Incorrect password
100 unknown Unknown error 
						

							34
ÙCommand name : +CGEQMIN=[parameter]

KOutline
Set the criteria for judging whether to permit QoS (Quality of Service) provisioned by the network when 
packet communication is established.

KFormat
AT+CGEQMIN= [ [,, [,] ] ]

KParameter description
 : 1-10
 : None (default) or 5,760
 : None (default) or 7,232
* For  and , the maximum communication speed (in kbps) is set for both 
upload and download traffic between FOMA terminal and the base  station. If the parameter is set to None (default), all 
speeds are permissible. If 5,760 and 7,232 are set, any connec tion at a speed less than the above limit is not permitted, 
and chances are that packet comm unication will not be connected.

KExample of execution
- Command used to permit all speeds both upload and download (when =5)
AT+CGEQMIN=5
OK
- Command used to permit only 5,760kbps  upload and 7,232kbps download (when =6)
AT+CGEQMIN=6,,5760,7232
OK
- Command used to permit only 5,760kbps upload and all speeds download (when =7) AT+CGEQMIN=7,,5760
OK
- Command used to permit all speeds upload and only 7,232kbps download (when =8)
AT+CGEQMIN=8,,,7232
OK

KOperation performed when parameter is omitted
AT+CGEQMIN= : Returns all  to the setting by default.
AT+CGEQMIN= : Returns the specified  to the setting by default.
AT+CGEQMIN? : Displays current settings.
AT+CGEQMIN=? : Displays a list of assignable values.
Ù Command name : +CGEQREQ=[parameter]

KOutline
Set QoS (Quality of Service) requested to the ne twork at the transmission of packet communication.

KFormat
AT+CGEQREQ= []

KParameter description
Only commands that require connection at 64-5,760kbps upload, 64-7,232kbps download can be set. The 
contents are set by default for each .
 : 1-10

KExample of execution
(when =3)
AT+CGEQREQ=3
OK

KOperation performed when parameter is omitted
AT+CGEQREQ= : Returns all  to the setting by default.
AT+CGEQREQ= : Returns the specified  to the setting by default.
AT+CGEQREQ? : Displays current settings.
AT+CGEQREQ=? : Displays a list of assignable values. 
						

							35
×Result codes

KWhen ATV command is set to n=1 (default), the result  code is displayed in alphabetic characters. When 
the command is set to n=0, the result code is displayed numerically. àP28
Ù Result codes
Ù Extended result code

K
When AT&E is set to n=0

KWhen AT&E is set to n=1
* To retain compatibility with a modem connected via conventional RS-232C, communication speed is displayed, but it 
differs from the actual connection speed  because FOMA terminal is connected to a PC with a USB cable or Bluetooth 
function.
Ù Communication protocol result code
No.Text displayMeaning
0 OK Operation performed normally
1 CONNECT Terminal connected to other party
2 RING Incoming call
3 NO CARRIER Line disconnected
4 ERROR Unable to accept command
6 NO DIALTONE Unable to detect dial tone
7 BUSY Detecting the busy tone
8 NO ANSWER Completed connection Time-out
100 RESTRICTION Network restriction in place (The communication network is 
busy. Please wait for a while and retry.)
101 DELAYED Redial call restricted
No.Text displayConnection speed between FOMA terminal and base station
122 CONNECT 64000 64000bps
125 CONNECT 384000 384000bps
133 CONNECT 3648000 3648000bps
135 CONNECT 7232000 7232000bps
No.Text displayConnection speed between FOMA terminal and a PC
5 CONNECT 1200 1200bps
10 CONNECT 2400 2400bps
11 CONNECT 4800 4800bps
13 CONNECT 7200 7200bps
12 CONNECT 9600 9600bps
15 CONNECT 14400 14400bps
16 CONNECT 19200 19200bps
17 CONNECT 38400 38400bps
18 CONNECT 57600 57600bps
19 CONNECT 115200 115200bps
20 CONNECT 230400 230400bps
21 CONNECT 460800 460800bps
No.Text displayMeaning
1 PPPoverUD Connect via 64K data communication (BC=UDI, +CBST=116,1,0)
3 AV64K Connect via 64K videophone
5 PACKET Connect via packet communication 
						

							36
ÙDisplay example of result codeWhen ATX0 is set
Regardless of the settings of AT ÇV command, only CONNECT is displayed upon completion of 
connection.
Text display example : ATD Î99 ÎÎÎ 1#
CONNECT
Number display example : ATD Î99 ÎÎÎ 1#
       1
When ATX1 is set

KWhen ATX1, AT ÇV0 (default) is set
Upon completion of connection, the result code is  displayed in the following format : CONNECT .
Text display example : ATD Î99 ÎÎÎ 1#
                                       CONNECT 460800
Number display example : ATD Î99 ÎÎÎ 1#
                                              1 21

KWhen ATX1, AT ÇV1 is set*1
The code is displayed upon completion of connection in the following format.
CONNECT/
/
*2
Text display example : ATD Î99 ÎÎÎ 1#
yyyyyy CONNECT 460800 PACKET mopera.ne.jp/5760/7232
(Indicates the terminal is connected to mopera.ne. jp providing a maximum upload speed of 5,760kbps 
and a maximum download speed of 7,232kbps.)
Number display example : ATD Î99 ÎÎÎ 1#
                                              1 21 5
*1 When ATX1 and AT ÇV1 are set at the same time, it is likely that  dialup connection will fail. It is recommended that 
only AT ÇV0 be used.
*2 When AT ÇV1 is set,  and the foll owing are displayed only when packet is used for 
connection. 
						

							1
Kuten Code List
For entering characters using code, see Entering characters using code in the attached manual.
Note that some characters in the code input list may look different from actual ones.
1st
-3rd4th digit of code1st
-3rd4th digit of code1st
-3rd4th digit of code
01234 56789 01234 56789 01234 56789
010
¢µÖ”µ£  z  {  |  }~
						

							2
^332

¶
· 
¸ 
¹ 
º 391
àáâãä åæçèé
261 #f392
ê
262 $%&( )*+,- 332

»
¼
½
¾
¿w
263 ./012 34567 333

À
Á
Â
Ã
Ä 
Å
Æ
Ç
È
É 392
ëìíî ïð  ñ  òó
264 89:;< =>?@A 334

Ê
Ë
Ì
Í
Î 
Ï
Ð
Ñ
Ò
Ó 393
ôõö÷ø
265 BCDEF GHIJK 335

Ô
Õ
Ö
×
Ø 
Ù
Ú
Û
Ü
Ý
x
266 LMNOP QRSTU 336

Þ
ß
à
á
â 
ã
ä
å
æ
ç 393
ùúûüý
267 VWXYZ [\]^_ 337

è
é
ê
ë
ì 
í
î
ï
ð
ñ 394
þÿ 



 





268 `abcd efghi 338

ò
ó
ô
õ
ö 
÷
ø
ù
ú
û 395


	


 






269 jk l m n 339


						

							3
447òó ô 510
  588
õö÷øù úûüýþ 511
 ! #$%& 589

						

							4
666ÑÒÓÔÕ Ö×ØÙÚ 743
£¤¥¦§ ¨©ª«¬ 820
vwxy z{|}~
667 ÛÜÝÞß àáâãä 744
­®¯°± ²³´µ¶ 821