Fujifilm Camera X30 Owners Manual

							[POWER SAVE]
[HIGH PERFORMANCE]
Adjust power management settings.
[AUTO POWER OFF]
[QUICK START MODE]
[POWER MANAGEMENT]
Choose the length of time before  the camera turns off automatically when no operations are
performed. Shorter times increase battery life; if  [OFF] is selected, the camera must be turned off
manually. Note that in some situa tions the camera turns off automatically even when [OFF] is
selected.
Allow the camera to restart in a  fast manner after turned off ([ON/OFF]).
If [ON]  is selected, the camera will continue to draw a small amount o f current from the
battery even when off. Quick start mode is cancelled automatical ly if no operations are
performed for about 20 minutes.
Optimize camera performance for increased battery life or displ ay quality.
Reduces display refresh rate. Th e display dims to save power if no
operations are performed for a short period, but can be restore d
by operating camera controls. Select this option to save power.
Choose for a brighter display and faster focus.
[POWER MANAGEMENT]
002D0020 0032003200310020 002D  
						

							Choose from the following image stabilization options: [CONTINUOUS + MOTION] /   [CONTINUOUS]
Image stabilization on. If +  [MOTION] is selected, the camera will adjust shutter speed to
reduce motion blur when a moving objects are detected.
 [SHOOTING + MOTION] /   [SHOOTING ONLY]
As above, except that image stabilization is pe rformed only when the shutter button is pressed
halfway or the shutter is released.
[OFF]
Image stabilization off. Choose this option when using a tripod.
+  [MOTION]  has no effect when sensitivity is set to a fixed value, and may also be
unavailable at some other combinations of settings. The effect may vary with lighting
conditions and the speed at which the object is moving.
[IS MODE]
002D0020 0032003200320020 002D  
						

							Choose [ON] to remove red-eye effects caused by the flash when shooting with Intelligent Face
Detection.
Red-eye reduction is performed only when a face is detected.
Red-eye removal is not available with RAW images.
[RED EYE REMOVAL]
002D0020 0032003200330020 002D  
						

							If [AE&AF ON WHEN PRESSING]  is selected, exposure and /or focus will lock while the
[AEL/AFL]  button is pressed. If  [AE&AF ON/OFF SWITCH]  is selected, exposure and /or focus
will lock while the  [AEL/AFL] button is pressed and remain loc ked until the button is pressed
again.
[AE/AF-LOCK MODE]
002D0020 0032003200340020 002D  
						

							[AE LOCK ONLY][AF LOCK ONLY] [AE/AF LOCK]
Choose whether the  [AEL/AFL] button locks exposure (AE), focus (AF), or both.
The  [AEL/AFL] button locks exposure only.
The  [AEL/AFL] button locks focus only.
The  [AEL/AFL] button locks both exposure and focus.
[AE/AF-LOCK BUTTON]
002D0020 0032003200350020 002D  
						

							[CONTINUOUS][RENEW]
Adjust file-management settings.
[FRAME NO.]
[SAVE ORG IMAGE]
[DATE STAMP]
New pictures are stored in image files named using a four-digit  file number assigned by adding one
to the last file number used. Th e file number is displayed during  playback as shown at right.
[FRAME NO.] controls whether file numbering  is reset to 0001 when a new memory card is
inserted or the current memory ca rd or internal memory is formatted.
Frame number
Directory number
File number Numbering continues from the las t file number used or the first available
file number, whichever is higher. Choose this  option to reduce the
number of pictures with duplicate file names.
Numbering is reset to 0001 after  formatting or when a new memor y
card is inserted.
If the frame number reaches 999-9999, the shutter release will  be disabled.
Selecting [RESET] sets [FRAME NO.] to  [CONTINUOUS] but does not reset the file
number.
Frame numbers for pictures taken with other cameras may differ.
[SAVE DATA SET-UP]
002D0020 0032003200360020 002D  
						

							+
[OFF]
Choose  [ON] to save unprocessed copies of se amless panoramas or pictures taken using  [RED
EYE REMOVAL] , [PRO LOW-LIGHT MODE] , or [PRO FOCUS MODE].
Stamp the time and /or date of recording on photographs as they  are taken.
Stamp new photographs with the date and time of recording.
Stamp new photographs with  the date of recording.
Do not stamp the time and date on new photographs.
Time and date stamps can not be deleted. Turn  [DATE STAMP] off to prevent time and
date stamps appearing on new photographs.
If the camera clock is not set, you will be prompted to set the  clock to the current date and
time.
We recommend that you turn the D POF “print date” option off when printing images with a
time and date stamp.
Time and date stamps do not appear on movies, panoramas, or pic tures taken with best
frame capture.
[SAVE DATA SET-UP]
002D0020 0032003200370020 002D  
						

							Choose the units used for the focus distance indicator.
[FOCUS SCALE UNITS]
002D0020 0032003200380020 002D  
						

							Adjust settings for connection to wireless networks.
[GENERAL SETTINGS]
[RESIZE IMAGE FOR SMARTPHONE] 
[PC AUTO SAVE SETTINGS]
Choose a name ([NAME]) to identify the camera on the  wireless network (the camera is assigned
a unique name by default) or select  [RESET WIRELESS SETTINGS] to restore default settings.
Choose [ON] (the default setting, recommend ed in most circumstances) to resize larger images to
 for upload to smartphones,  [OFF] to upload images at their original size. Resizing applies only
to the copy uploaded to the smar tphone; the original is not affected.
Choose [DELETE REGISTERED DESTINATION PC]  to remove selected destinations, [DETAILS
OF PREVIOUS CONNECTION]  to view computers to which the camera has recently connected.
See Also
The FUJIFILM Smartphone /Tablet /Computer App  (opens in another window)
[WIRELESS SETTINGS]
002D0020 0032003200390020 002D  
						

							Choose an upload destination. Choose [SIMPLE SETUP] to connect using WPS,  [MANUAL
SETUP] to configure network settings manually.
See Also
The FUJIFILM Smartphone /Tablet /Computer App  (opens in another window)
[PC AUTO SAVE SETTING]
002D0020 0032003300300020 002D