Home > Ford > Automobile > Ford Fusion 16 Owners Manual

Ford Fusion 16 Owners Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Ford Fusion 16 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 41 Ford manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 518
    							Note:
    The keys that came with your vehicle
    have a security tag that provides important
    vehicle key cut information. Keep the tag in
    a safe place for future reference.
    Intelligent Access Key (If Equipped) Your intelligent access keys operate the
    power locks and the remote start system.
    The key must be in your vehicle to activate
    the push-button start system.
    Removable Key Blade
    The intelligent access key also contains a
    removable mechanical key blade that you
    can use to unlock the driver door. Slide the release on the back of the remote
    control and pivot the cover off to access
    the key blade.
    Note:
    The backup keys that came with your
    vehicle have a security tag that provides
    important vehicle key cut information. Keep
    the tag in a safe place for future reference.
    Using the Key Blade
    The key cylinder is under a cap on the driver
    door handle.
    To remove the cap:
    48
    Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing Keys and Remote ControlsE151795 E144506 E151796 E151795 
    ,QIRUPDWLRQ3URYLGHGE\  
    						
    							1.
    Insert the key blade into the slot on the
    bottom of the handle and press up.
    2. Applying upward pressure, move the cap rearward to release it. Gently
    remove the key while doing so.
    To install the cap: 1. Place the cap just forward of the key
    cylinder.
    2. Applying pressure to the cap, move it forward until it is in place. You may
    hear a snap as it engages.
    Make sure you have properly installed the
    cap by trying to move it rearward. Replacing the Battery
    Note:
    Refer to local regulations when
    disposing of transmitter batteries.
    Note: Do not wipe off any grease on the
    battery terminals or on the back surface of
    the circuit board.
    Note: Replacing the battery will not delete
    the transmitter from the vehicle. The
    transmitter should operate normally.
    A message appears in the information
    display when the remote control battery
    is low.  See Information Messages (page
    105).
    Integrated Keyhead Transmitter
    The remote control uses one coin-type
    three-volt lithium battery CR2032 or
    equivalent.
    Press the button to release the key before
    beginning the procedure. 1. Insert a screwdriver in the position
    shown and gently push the clip.
    2. Press the clip down to release the battery cover.
    49
    Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing Keys and Remote ControlsE151956  E151957 E151798 
    ,QIRUPDWLRQ3URYLGHGE\  
    						
    							3. Carefully remove the cover.
    Note:
    Do not touch the battery contacts or
    the printed circuit board with the
    screwdriver.
    4. Insert a screwdriver as shown to release the battery. 5. Remove the battery. 6. Install a new battery with the + facing
    up.
    7. Replace the battery cover.
    Intelligent Access Transmitter
    The remote control uses two coin-type
    three-volt lithium batteries CR2025 or
    equivalent. 1. Slide the release on the back of the
    remote control and pivot the cover off. 2. Insert a coin into the slot and twist to
    separate the housing.
    50
    Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing Keys and Remote ControlsE151799  E151801 E151796 E153890 
    ,QIRUPDWLRQ3URYLGHGE\  
    						
    							3. Remove the batteries.
    4. Install new batteries with the + facing
    each other.
    Note: Make sure to replace the label
    between the two batteries.
    5. Reinstall the housing and cover.
    Car Finder Press the button twice within
    three seconds. The horn sounds
    and the direction indicators
    flash. We recommend you use this method
    to locate your vehicle, rather than using
    the panic alarm.
    Sounding a Panic Alarm
    Note: The panic alarm will only operate
    when the ignition is off. Press the button to activate the
    alarm. Press the button again or
    switch the ignition on to
    deactivate.
    Remote Start 
     (If Equipped) WARNING
    To avoid exhaust fumes, do not use
    remote start if your vehicle is parked
    indoors or areas that are not well
    ventilated. Note:
    Do not use remote start if your vehicle
    is low on fuel. The remote start button is on the
    transmitter.
    This feature allows you to start your
    vehicle from outside the vehicle. The
    transmitter has an extended operating
    range.
    If your vehicle has automatic climate
    control, you can configure it to operate
    when you remote start your vehicle.  See
    Climate Control
     (page 120).  See
    Information Displays (page 96).  A
    manual climate control system will run at
    the setting it was set to when you switched
    the vehicle off.
    Many states and provinces have
    restrictions for the use of remote start.
    Check your local and state or provincial
    laws for specific requirements regarding
    remote start systems.
    The remote start system will not work if:
    • The ignition is on.
    • The alarm system triggered.
    • You disable the feature.
    • The hood is open.
    • The transmission is not in park (
    P).
    • The vehicle battery voltage is too low.
    • The service engine soon light is on.
    Remote Control Feedback (If
    Equipped)
    An LED on the remote control provides
    status feedback of remote start or stop
    commands.
    51
    Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing Keys and Remote ControlsE153891 E138623 E138624 E138625 
    ,QIRUPDWLRQ3URYLGHGE\  
    						
    							Status
    LED
    Remote start orextension
    successful.
    Solid green.
    Remote stop
    successful; vehicle off.
    Solid red.
    Remote start orstop failed.
    Blinking red.
    Waiting for statusupdate.
    Blinking green.
    Remote Starting the Vehicle
    Note: You must press each button within
    three seconds of each other. Your vehicle
    will not remote start if you do not follow this
    sequence. The tag with your transmitter details the
    starting procedure.
    To remote start your vehicle:
    1. Press the lock button to lock all the
    doors.
    2. Press the remote start button twice. The exterior lamps flash twice.
    The horn sounds if the system fails to start,
    unless quiet start is on. Quiet start will run
    the blower fan at a slower speed to reduce
    noise. It can be switched on or off in the
    information display.  See  (page 96). Note:
    If you remote start the vehicle with
    an integrated keyhead transmitter, you must
    switch the ignition on before driving your
    vehicle. With an intelligent access
    transmitter, you must press the
    START/STOP
     button on the instrument
    panel once while applying the brake pedal
    before driving your vehicle.
    The power windows will not work during
    the remote start and the radio will not turn
    on automatically.
    The parking lamps will remain on and the
    vehicle will run for 5, 10 or 15 minutes,
    depending on the setting.
    Extending the Vehicle Run Time
    Repeat Steps 1 and 2 with the vehicle still
    running to extend the run time for another
    remote start duration. If you programmed
    the duration to last 10 minutes, the second
    10 minutes will begin after what is left of
    the first activation time. For example, if the
    vehicle had been running from the first
    remote start for five minutes, the vehicle
    will continue to run now for a total of 15
    minutes. You can extend the remote start
    up to a maximum of 35 minutes.
    Wait at least five seconds before remote
    starting after a vehicle shutdown.
    Turning the Vehicle Off After Remote
    Starting Press the button once. The
    vehicle and parking lamps will
    turn off.
    You may have to be closer to the vehicle
    than when starting due to ground reflection
    and the added noise of the running vehicle.
    You can disable or enable the remote start
    system through the information display.
    See 
     (page 96).
    52
    Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing Keys and Remote ControlsE138626 E138625 
    ,QIRUPDWLRQ3URYLGHGE\  
    						
    							Memory Feature
    If programmed to a pre-set position, the
    integrated keyhead transmitter or
    intelligent access key recalls the driver seat
    and exterior mirror positions when you
    unlock your vehicle. It also recalls the
    power steering column and pedal
    positions.  See Memory Function (page
    134).
    REPLACING A LOST KEY OR
    REMOTE CONTROL
    Replacement keys or remote controls can
    be purchased from an authorized dealer.
    Authorized dealers can program remote
    controls for your vehicle.  See 
    Passive
    Anti-Theft System (page 68).
    To re-program the passive anti-theft
    system see an authorized dealer.
    53
    Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing Keys and Remote Controls
    ,QIRUPDWLRQ3URYLGHGE\  
    						
    							PRINCIPLE OF OPERATION
    MyKey allows you to program keys with
    restricted driving modes to promote good
    driving habits. All but one of the keys can
    be activated with these restricted modes.
    Any keys that remain unprogrammed are
    referred to as administrator keys or admin
    keys. They can be used to:
    •
    Create a MyKey.
    • Program configurable MyKey settings.
    • Clear all MyKey features.
    When you have created a MyKey, you can
    access the following information by using
    the information display to determine:
    • How many admin keys and MyKeys are
    programmed to your vehicle.
    • The total distance your vehicle traveled
    with a MyKey.
    Note: Switch the vehicle on to use the
    system.
    Note: All MyKeys are programmed to the
    same settings. You cannot program them
    individually.
    Note: For vehicles equipped with
    push-button start, when both a MyKey and
    an admin remote transmitter are present,
    the admin remote transmitter will be
    recognized by the vehicle while switching
    the vehicle on to start the vehicle. Non-configurable Settings
    The following settings cannot be changed
    by an admin key user:
    •
    Safety belt reminder. You cannot
    disable this feature. The audio system
    will mute when the front seat
    passengers’  safety belts are not
    fastened.
    • Early low fuel or charge. The low-fuel
    or low charge warning activates earlier,
    giving the MyKey user more time to
    refuel or recharge.
    • Driver assist features, if equipped on
    your vehicle, are forced on: parking aid
    and Blind Spot Information System
    (BLIS) with cross traffic alert.
    • Satellite radio adult content
    restrictions, if equipped on your vehicle.
    Configurable Settings
    With an admin key, you can configure
    certain MyKey settings when you first
    create a MyKey and before you recycle the
    key or restart the vehicle. You can also
    change the settings afterward with an
    admin key.
    • A vehicle speed limit can be set.
    Warnings will be shown in the display
    followed by an audible tone when your
    vehicle reaches the set speed. You
    cannot override the set speed by fully
    depressing the accelerator pedal or by
    setting cruise control. WARNING
    Do not set MyKey maximum speed
    limit to a limit that will prevent the
    driver from maintaining a safe speed
    considering posted speed limits and
    prevailing road conditions. The driver is
    always responsible to drive in accordance
    with local laws and prevailing conditions.
    Failure to do so could result in accident or
    injury. 54
    Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing MyKey
    ™
    ,QIRUPDWLRQ3URYLGHGE\  
    						
    							•
    Various vehicle speed minders can be
    set. Once you select a speed, it will be
    shown in the display, followed by an
    audible tone when the preselected
    vehicle speed is exceeded.
    • Audio system maximum volume of
    45%. A message will be shown in the
    display when you attempt to exceed
    the limited volume. Also, the
    speed-sensitive or compensated
    automatic volume control will be
    disabled.
    • Always on setting. When this is
    selected, you will not be able to switch
    off Advance Trac or traction control,
    911 Assist or Emergency Assist, or the
    do not disturb feature (if your vehicle
    is equipped with these features). CREATING A MYKEY
    Use the information display to create a
    MyKey:
    1. Insert the key you want to program into
    the ignition. If your vehicle is equipped with
    a push-button start, place the intelligent
    access key fob into the backup slot. The
    location of your backup slot is in another
    chapter.  See Starting and Stopping the
    Engine (page 146).
    2. Switch the ignition on.
    3. Access the main menu on the
    information display controls. Use the arrow
    keys to get to the following menu
    selections: Action and Description
    Message
    Press the OK button or the right arrow key.
    Settings
    Press the OK button or the right arrow key.
    MyKey
    Press the OK button or the right arrow key.
    Create MyKey
    When prompted, hold the OK button until
    you see a message informing you to label
    this key as a MyKey. The key will be
    restricted at the next start.
    MyKey is successfully created. Make sure
    you label it so you can distinguish it from
    the admin keys.
    You can also program configurable
    settings for the key(s). See
    Programming/Changing Configurable
    Settings
    . Programming/Changing
    Configurable Settings
    Use the information display to access your
    configurable MyKey settings.
    1. Switch the ignition on using an admin
    key or fob.
    2. Access the main menu on the information display controls. Use the
    arrow keys to get to the following menu
    selections: Action and Description
    Message
    Press the OK button or the right arrow key.
    Settings
    Press the OK button or the right arrow key.
    MyKey
    55
    Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing MyKey
    ™
    ,QIRUPDWLRQ3URYLGHGE\  
    						
    							Note:
    You can clear or change your MyKey
    settings at any time during the same key
    cycle as you created the MyKey. Once you
    have switched the vehicle off, however, you
    will need an admin key to change or clear
    your MyKey settings. CLEARING ALL MYKEYS
    You can clear or change your MyKey
    settings using the information display
    control on the steering wheel.  See
    Information Displays (page 96).
    Switch the ignition on using an admin key
    or fob.
    To clear all MyKeys of all MyKey settings, press the left arrow button to access
    the main menu and scroll to: Action and Description
    Message
    Press the 
    OK button.
    Settings
    Press the 
    OK button.
    MyKey
    Press and hold the 
    OK button until the following message
    displays.
    Clear MyKey
    All MyKeys
    Cleared
    Note: When you clear your MyKeys, you remove all restrictions and return all MyKeys to
    their original admin key status.
    56
    Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing MyKey
    ™
    ,QIRUPDWLRQ3URYLGHGE\  
    						
    							CHECKING MYKEY SYSTEM
    STATUS
    You can find information on programmed
    MyKey(s) using the information display
    control on the steering wheel.  See
    Information Displays (page 96).
    To find information on programmed MyKey(s), press the left arrow button to
    access the main menu and scroll to: Description
    Message
    Press the 
    OK button.
    Settings
    Press the 
    OK button.
    MyKey
    Select one of the following:
    Tracks the distance when drivers use a MyKey. The only way
    to delete the accumulated distance is by using an admin key
    to clear your MyKeys. If the distance does not accumulate as
    expected, then the intended user is not using the MyKey, or
    an admin key user recently cleared and then recreated a
    MyKey.
    MyKey Dist.
    Indicates the number of MyKeys programmed to your vehicle.
    Use this feature to detect how many MyKeys you have for
    your vehicle and determine when a MyKey has been deleted.
    {0} MyKeys
    Indicates how many admin keys are programmed to your
    vehicle. Use this feature to determine how many unrestricted
    keys you have for your vehicle, and detect if an additional
    MyKey has been programmed.
    {0} Admin Keys
    57
    Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing MyKey
    ™
    ,QIRUPDWLRQ3URYLGHGE\  
    						
    All Ford manuals Comments (0)

    Related Manuals for Ford Fusion 16 Owners Manual