Ford Fusion 16 Owners Manual
Have a look at the manual Ford Fusion 16 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 41 Ford manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
9. The vehicle jacking points are shown here, and can be identified by the triangle markings on the molding. The triangle marking may be located on the side or the underside of the molding. The jacking points are identified on vehicles without moldings by a pair of arrows on the metal flange pointing to the jacking point between them. Details are depicted on the warning label on the jack. 10. Place the jack at the jacking point next to the tire you are changing. Turn the jack handle clockwise until the wheel is completely off the ground. 11. Remove the lug nuts with the lug wrench. 12. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. If you are using the temporary tire, the lug nut washers will not appear to be flush with the rim. This is normal only when using the temporary spare tire. 13. Lower the wheel by turning the jack handle counterclockwise. 14. Remove the jack and fully tighten the lug nuts in the order shown. See Changing a Road Wheel (page 305). 15. Put the flat tire, jack and lug wrench away. Make sure the jack is fastened securely before you drive. 16. Unblock the wheel. Type 2 1. Park on a level surface, set the parking brake and activate the hazard flashers. 2. Place the transmission in park (P) and turn the engine off. For vehicles with a manual transmission, place the transmission in reverse (R) after the engine is turned off. 308 Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing Wheels and TiresE174775 12 3 4 5 E75442 ,QIRUPDWLRQ3URYLGHGE\
3. Block both the front and rear of the wheel diagonally opposite the flat tire. For example, if the left front tire is flat, block the right rear wheel. 4. Remove the carpeted wheel cover. 5. Remove the spare tire bolt securing the spare tire by turning it counterclockwise. 6. Remove the spare tire from the spare tire compartment. 7. Remove the lug wrench and jack from the spare tire compartment. 8. Loosen each wheel lug nut one-half turn counterclockwise, but do not remove them until the wheel is raised off the ground. 9. The vehicle jacking points are shown here, and can be identified by the triangle markings on the molding. The triangle marking may be located on the side or the underside of the molding. The jacking points are identified on vehicles without moldings by a pair of arrows on the metal flange pointing to the jacking point between them. Details are depicted on the warning label on the jack. 309 Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing Wheels and TiresE175447 E178186 E145908 E174775 ,QIRUPDWLRQ3URYLGHGE\
10. Place the jack at the jacking point next to the tire you are changing. Turn the jack handle clockwise until the wheel is completely off the ground. 11. Remove the lug nuts with the lug wrench. 12. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. If you are using the temporary tire, the lug nut washers will not appear to be flush with the rim. This is normal only when using the temporary spare tire. 13. Lower the wheel by turning the jack handle counterclockwise.14. Remove the jack and fully tighten the lug nuts in the order shown. See Changing a Road Wheel (page 305). 15. Put the flat tire, jack and lug wrench away. Make sure the jack is fastened securely before you drive. 16. Unblock the wheel. Stowing the flat tire (Type 1) You can stow the full-size road wheel in the spare tire compartment. 1. Lift the carpeted wheel cover at an angle to access the spare tire compartment. 2. Place the wheel in the spare tire well with the valve stem facing down. Use the mini-spare bolt to secure the wheel through one of the lug holes. 3. Place the jack, tools and foam block back into the spare tire compartment. 4. Replace the carpeted wheel cover. Stowing the flat tire (Type 2) You can stow the full-size road wheel in the spare tire compartment. 1. Lift the carpeted wheel cover at an angle to access the spare tire compartment. 2. Place the wheel in the spare tire well with the valve stem facing down. Use the mini-spare bolt to secure the wheel through one of the lug holes. 3. Place the jack and tools back into the spare tire compartment. 4. Replace the carpeted wheel cover. 310 Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing Wheels and Tires12 3 4 5 E75442 E146026 ,QIRUPDWLRQ3URYLGHGE\
TECHNICAL SPECIFICATIONS Wheel Lug Nut Torque Specifications WARNING When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Make sure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the wheel. Installing wheels without correct metal-to-metal contact at the wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while your vehicle is in motion, resulting in loss of control. Ib-ft (Nm) * Bolt size 100 (135) M12 x 1.5 * Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners. Retighten the lug nuts to the specified torque within 100 miles (160 kilometers) after any wheel disturbance (such as tire rotation, changing a flat tire, wheel removal). 311 Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing Wheels and TiresE178187 ,QIRUPDWLRQ3URYLGHGE\
Wheel pilot bore A Inspect the wheel pilot bore and mounting surface prior to installation. Remove any visible corrosion or loose particles. 312 Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing Wheels and TiresE145950 ,QIRUPDWLRQ3URYLGHGE\
ENGINE SPECIFICATIONS 2.5L engine 2.0L EcoBoost engine 1.5L EcoBoost engine Engine 152 122 92 Cubic inches Minimum 87 octane Minimum 87 octane Minimum 87 octane Required fuel 9.7:1 9.3:1 10.0:1 Compression ratio 0.049-0.053 in.(1.25-1.35 mm) 0.027-0.031 in. (0.70-0.80 mm) 0.025-0.029 in. (0.65- 0.75 mm) Spark plug gap Drivebelt Routing 1.5L engine 2.0L and 2.5L engines A. Long drivebelt is on first pulley groove closest to engine B. Short drivebelt is on second pulley groove farthest from engine MOTORCRAFT PARTS 2.5L Engine 2.0L EcoBoost Engine 1.5L EcoBoost Engine Component FA-1912 Air filter element FL-910S Oil filter BXT-90T5-500 BXT-90T5-590 1 BXT-90T5-500 Battery BXT-90T5-5901 BXT-90T5-5901 BAGM-48H6-760 2 313 Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing Capacities and SpecificationsE167586 E161383 A B ,QIRUPDWLRQ3URYLGHGE\
2.5L Engine 2.0L EcoBoost Engine 1.5L EcoBoost Engine Component SP-530 SP-537 SP-539 Spark plugs FP-71 Cabin air filter WW-2601 (driver side) Windshield wiper blade WW-2700 (passenger side) 1 This part is designed for vehicles with Intelligent Access. 2 This part is designed for vehicles with Automatic-Start-Stop. We recommend Motorcraft replacement parts available at your Ford dealer or at fordparts.com for scheduled maintenance. These parts meet or exceed Ford Motor Company ’s specifications and are engineered for your vehicle. Use of other parts may impact vehicle performance, emissions and durability. Your warranty may be void for any damage related to use of other parts. If a Motorcraft oil filter is not available, use an oil filter that meets industry performance specification SAE/USCAR-36. For spark plug replacement, contact an authorized dealer. Replace the spark plugs at the appropriate intervals. See Scheduled Maintenance (page 464). 314 Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing Capacities and Specifications ,QIRUPDWLRQ3URYLGHGE\
VEHICLE IDENTIFICATION NUMBER The vehicle identification number is located on the left-hand side of the instrument panel. Please note that in the graphic, XXXX is representative of your vehicle identification number. The Vehicle Identification Number contains the following information: World manufacturer identifier A Brake system, Gross Vehicle Weight Rating, Restraint Devices and their locations B Make, vehicle line, series, body type C Engine type D Check digit E Model year F Assembly plant G Production sequence number H VEHICLE CERTIFICATION LABEL The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label shall be affixed to either the door hinge pillar, the door latch post, or the edge of the door near the door latch, next to the driver's seating position. 315 Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing Capacities and SpecificationsE142476 E142477 E167469 ,QIRUPDWLRQ3URYLGHGE\
TRANSMISSION CODE DESIGNATION The transmission code is on the Safety Compliance Certification Label. The following table shows the transmission code along with the transmission description. Code Description W Six-speed automatic transmis- sion. CAPACITIES AND SPECIFICATIONS - 1.5L ECOBOOST™ Capacities WARNING The air conditioning refrigerant system contains refrigerant R-134a under high pressure. Only qualified personnel should service the air conditioning refrigerant system. Opening the air conditioning refrigerant system can cause personal injury. Capacity Item 4.3 qt (4.1 L) Engine oil 11.1 qt (10.5 L) Engine coolant Between MIN/MAX on brake fluid reservoir Brake fluid 9.0 qt (8.5 L) Automatic transmission fluid 1 Fill as required Windshield washer fluid 16.5 gal (62.5 L) Fuel tank (Front Wheel Drive) 316 Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing Capacities and SpecificationsE167814 ,QIRUPDWLRQ3URYLGHGE\
Capacity Item 20 oz (0.56 kg) A/C refrigerant 5.2 fl oz (153.8 ml) A/C refrigerant compressor oil 1 Approximate dry fill capacity. Actual amount may vary during fluid changes. Specifications Materials Specification Name WSS-M2C945-A Recommended motor oil (U.S.): Motorcraft SAE 5W-20 Premium Synthetic Blend Motor Oil XO-5W20-QSP WSS-M2C945-A Recommended motor oil (Canada): Motorcraft SAE 5W-20 Super Premium Motor Oil CXO-5W20-LSP12 WSS-M2C945-A Recommended motor oil (Mexico): Motorcraft SAE 5W-20 Synthetic Motor Oil MXO-5W20-QSP WSS-M2C945-A Optional motor oil (U.S. and Mexico): Motorcraft SAE 5W-20 Full Synthetic Motor Oil XO-5W20-QFS WSS-M2C945-A Optional motor oil (Canada): Motorcraft SAE 5W-20 Synthetic Motor Oil CXO-5W20-LFS12 WSS-M97B44-D2 Engine coolant (U.S. and Mexico): Motorcraft Orange Antifreeze/Coolant Prediluted VC-3DIL-B WSS-M97B44-D2 Engine coolant (Canada): Motorcraft Orange Antifreeze/Coolant Prediluted CVC-3DIL-B WSS-M6C65-A2 Brake fluid: Motorcraft DOT 4 Low Viscosity (LV) High Performance Motor Vehicle Brake Fluid PM-20 WSS-M2C938-A Automatic transmission fluid (U.S. and Mexico): MERCON LV Motorcraft MERCON LV Automatic Transmission Fluid 317 Fusion/Mondeo (CC7) Canada/United States of America, enUSA, First Printing Capacities and Specifications ,QIRUPDWLRQ3URYLGHGE\