Epson Stylus Pro WT7900 User Manual

31
Setting Up the Printer|31
3. Insert the pins through the guides, pressing them into place.
4. Open one of the scissor arms as shown. Insert two long rods (A) and one 
short rod (B) into the plastic connectors.Note: Once inserted, the 
pins cannot be removed.
 

32
32|Setting Up the Printer
5. Feed the basket cloth onto rods A and B as shown.
6. Connect the other scissor arm as shown.
 

33
Setting Up the Printer|33
7. Insert six pins into the plastic connectors to secure the rods.
8. Set the basket upright, then press the straps onto the film basket in the 
indicated positions.
Now go to “Completing Setup and Connecting the Power Cord” on 
page 34.Note: Once inserted, the 
pins cannot be removed.
Note: Do not place heavy 
objects such as paper 
rolls in this basket, or it 
may get damaged. The 
basket can support up to 
6.6 lbs (3 kg).
 

34
34|Setting Up the Printer
Completing Setup and Connecting the Power 
Cord
1. Attach the manual holder to the left or right side of the stand. Store the 
printer manuals in the holder.
2. Unlock the casters. Then move the printer to the place of use. (The 
casters are meant for moving the printer for only a short distance.) Lock 
the casters after moving. 
 

35
Setting Up the Printer|35
3. Remove any packing tape and plastic film. Check these areas:
the front cover 
the ink compartment covers
the maintenance tank(s)
4. Open the roll paper cover and remove the tape and packing material.
Ti p :  After removing 
protective materials, 
touch a metal part of the 
printer to discharge static 
electricity.
 

36
36|Setting Up the Printer
5. Open the front cover and remove the tape and packing material.
Save the packing material in case you need to ship the printer.
6. Close the front cover.
7. Connect the power cord to the AC inlet on the back of the printer.
 

37
Setting Up the Printer|37
8. Attach the cable guides to the left or right side of the printer back and 
route the power cord to the side of the printer as shown.
9. Plug the power cord into a properly grounded electrical outlet.
Installing Ink
Use the ink cartridges that came with your printer for initial ink charging. 
During the initial installation process, it is normal for most of the ink in each 
cartridge to be used.
The cartridges shipped with your printer are provided mainly to charge the 
ink...

38
38|Setting Up the Printer
2. Open both ink covers.
3. Remove the ink cartridges from their packages. Gently shake each 
cartridge as shown below for the following durations:
White ink cartridge: 30 seconds (about 100 times)
Other ink cartridges: 5 seconds
Caution: Do not touch 
the green chip on top of 
the cartridge, or you may 
damage it.
 

39
Setting Up the Printer|39
4. Note the location of the slot corresponding to each cartridge.
5. Install the ink cartridges in the printer.
Hold each cartridge with the arrow pointing toward the printer, then 
insert it into its slot until it clicks into place. Make sure you insert each 
cartridge all the way into the correct slot.
Left ink bayRight ink bay
Slot no. Cartridge Slot no. Cartridge
1 Cyan (C) 7 Vivid Magenta (VM)
2 Orange (O) 8 Cleaning Liquid (CL)
3 Yellow (Y) 9 Green (G)
4 Light Cyan (LC)...

40
40|Setting Up the Printer
6. After installing all 11 cartridges, close the ink covers. The printer begins 
charging the ink delivery system and the Ppower
 light flashes.
After ink charging is completed, you need to load paper before 
READY will 
appear on the display.
Aligning the Print Head
Before using your printer, you need to align the print head for best results.
1. Load the bundled roll paper included with the printer. See page 49 for 
instructions on loading roll media.
When you’re prompted to...