Epson Stylus Pro WT7900 User Manual

11
Introduction|11
Where to Get Help
Epson provides technical support and information on the installation, 
configuration, and operation of professional printing products through the 
Epson Preferred  Limited Warranty Plan. Dial (888) 377-6611, 6
AM to 
6
PM, Pacific Time, Monday through Friday. Days and hours of support are 
subject to change without notice. 
Before you call, make sure you have your Unit ID number, which is 
included with the Epson Preferred Limited Warranty Plan information that 
came...

12
12|Introduction
Important Safety Instructions
Before using your printer, read the following safety instructions to make sure 
you use the equipment safely and effectively.
The Epson Stylus Pro WT7900 weighs approximately 220 lb (100 kg). 
When lifting it onto the stand, make sure you have four people holding 
the printer (see page 21).
When setting up the printer, make sure you have enough space around 
it (see page 17). Leave enough space in front so you can attach the film 
basket.
Place the printer...

13
Introduction|13

If you use an extension cord with the printer, make sure the total ampere 
rating of devices plugged into the extension cord does not exceed the 
cord’s ampere rating. Also, make sure the total ampere rating of all 
devices plugged into the wall outlet does not exceed the wall outlet’s 
ampere rating.
Do not block or cover the openings in the printer’s case.
Do not put your hand inside the printer during printing.
Do not move the print head by hand unless instructed to do so by an...

14
14|Introduction
Ink Cartridge Safety Instructions
Keep ink cartridges out of the reach of children and do not drink the 
ink.
Store ink cartridges in a cool, dark place.
If ink gets on your skin, wash it off with soap and water. If ink gets in 
your eyes, flush them immediately with water.
Shake all ink cartridges before installing them for best results (see 
page 88). White ink cartridges must be shaken regularly to maintain 
print quality, even after being installed (see page 78).
Do not use an ink...

15
Introduction|15
Printer Parts
These illustrations show the parts of the Epson Stylus Pro WT7900.
Front
Back
Roll paper cover
Control 
panel
Ink bay Ink bay Front cover
Paper basketCastersRoll paper holder
Film 
basket 
guide
Film basket
Manual 
holder
Network interface 
port
USB port
AC inlet Maintenance 
tank
Optional 
SpectroProofer 
port
 

16
16|Introduction
Control Panel
LCD Display
LCD 
display
Power 
light and 
button
Pause/reset 
light and buttonInk 
light
Paper source button Paper 
light
Menu button
Paper feed button (up)
Paper feed button (down)OK button
Paper cut 
button
Ink open button
Head cleaning buttonPaper release (ePlaten™) 
light and button
Platen gap 
setting
Paper 
sourceRoll paper 
margin
Days until white ink 
cartridge shaking Ink cartridge 
statusRoll paper 
remaining
Maintenance 
tank status
White ink or cleaning...

17
17
This chapter includes the following information:
Unpacking and assembling the Epson Stylus Pro WT7900
Connecting the power cord
Installing ink
Connecting to your computer and a network
Installing the printer software
Updating the printer firmware
Configuring the printer for a network
Unpacking and Assembling the Printer
Before you begin, make sure you have sufficient space to set up and use the 
printer—at least 12 inches (300 mm) on all sides in addition to these 
dimensions:
53 × 26 inches (1356...

18
18|Setting Up the Printer
Unpacking and Assembling the Stand
1. Lift the box up and away from the shipping pallet. Then remove the box 
containing the stand and paper basket.
2. Unpack the stand and make sure you have all these items.
3. Insert the strut into the left side as shown. (The sides are labeled 
L and 
R.)
2 SidesManual holder
Horizontal strutHex wrench6 Bolts
2 Wing screws with 
lock washers
Note: Make sure you 
tighten all bolts before 
moving to the next 
section.
 

19
Setting Up the Printer|19
4. Fasten the strut with 3 bolts as shown. Use the hex wrench to tighten the 
bolts.
 
 

20
20|Setting Up the Printer
5. Insert the strut into the right side and fasten it with 3 bolts as shown.
6. Lock the casters.