Epson Stylus Pro 7400 User Manual
Have a look at the manual Epson Stylus Pro 7400 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Paper Handling281 6 6 6 6 6 6 6 6 6 6 6 6 English 2. Pull the upper hooks out to their full length. Hook both ends of the center shaft on the upper basket hooks. 3. Make sure the lower shafts are in the upward position, and hook the basket rings on the upper basket hooks.
282Paper Handling For EPSON Stylus Pro 7800/7400 When feeding paper forward When feeding paper forward, put the paper basket down in the forward position, as shown below. Note: Feed the paper forward if it is thick (0.5 to 1.5 mm) or its length is 914.4 mm or more.
Paper Handling283 6 6 6 6 6 6 6 6 6 6 6 6 English When the paper basket is loosened, turn the following part to fix it. When feeding paper backward When feeding paper backward, turn the paper basket to the backward position, as shown below. Note: ❏You can feed the paper backward when its length is shorter than 914.4 mm; otherwise, feed the paper forward.
284Paper Handling ❏If the paper thickness is 0.5 mm or more, feed the paper forward.
Maintenance and Transportation285 7 7 7 7 7 7 7 7 7 7 7 7 English Chapter 7 Maintenance and Transportation Replacing Ink Cartridges When the printer’s Ink check light is flashing, this indicates that the ink is low and you need to obtain a replacement ink cartridge. When the Ink check light remains on, this indicates that there is no more ink and you need to replace the empty ink cartridge. The LCD panel also displays INK LOW or INK OUT. Note: Even if only one ink cartridge is empty, the printer cannot continue to print. Epson recommends the use of genuine Epson ink cartridges. Other products not manufactured by Epson may cause damage to your printer not covered by Epson’s warranties. For detailed information on ink cartridges, see “Ink cartridges” on page 368. To check the product codes of ink cartridges, see “Consumable Products” on page 375. To replace an ink cartridge, follow the steps below. c Caution: Leave the old ink cartridge installed in the printer until you are ready to replace it with a new one. 1. Make sure the printer is on. Find out which cartridge needs to be replaced, as indicated by the steady or flashing the Ink check light and the target ink icon.
286Maintenance and Transportation 2. Open the ink compartment cover by pushing it. 3. Raise the ink levers to the released position.
Maintenance and Transportation287 7 7 7 7 7 7 7 7 7 7 7 7 English 4. Carefully pull the empty cartridge straight out of the printer. w Warning: If ink gets on your hands, wash them thoroughly with soap and water. If ink gets into your eyes, flush them immediately with water. c Caution: Do not shake cartridges (that have been installed previously) with too much force. 5. Make sure the replacement ink cartridge is the correct color, and remove it from the package. Shake the ink cartridge well before installing it for best results.
288Maintenance and TransportationNote: A protection system is provided to prevent improper cartridge insertion. If you cannot insert the ink cartridge smoothly, the type of cartridge may be incorrect. Check the package and product code. 6. Hold the ink cartridge with the arrow mark facing up and pointing to the rear of the printer, and then insert it into the slot. Do not force the cartridge in further by hand. Note: ❏If the Ink check light remains on, this indicates the ink cartridge may not be installed correctly. Remove the ink cartridge and then reinsert it as described above. ❏If you install an ink cartridge in the wrong slot, the ink icon of the slot that you installed wrong ink cartridge blinks on the LCD. Make sure that the correct ink cartridge is installed in the correct slot.
Maintenance and Transportation289 7 7 7 7 7 7 7 7 7 7 7 7 English 7. Lower the ink lever to the secured position. 8. Close the ink compartment cover. The printer returns to the previous status.
290Maintenance and Transportation Converting the Black Ink Cartridges You can change the black ink according to your purpose. You can choose either Matte Black or Photo Black. c Caution: To avoid interrupting a black ink change, observe the following conditions: ❏Do not turn off the printer. ❏Do not open the front cover. ❏Do not move the paper lever to the released position. ❏Do not remove the ink cartridges. ❏Do not remove the maintenance tank. ❏Do not unplug the power cord. Note: ❏If an electrical power failure occurs during this operation, turn the printer on again. You can continue your procedure at the breakpoint. ❏The Black Ink Conversion Kit is required when changing the black ink. Also, the black ink cartridge (either Matte or Photo that you want to convert) is required. To check the product code, see “Consumable Products” on page 375. ❏If the maintenance tank icon tells that the maintenance tank is full or near full on the LCD, you need to replace the maintenance tank. See “Replacing the Maintenance Tank” on page 299. To change the black ink, follow the steps below. 1. Make sure that READY appears on the LCD panel.