Epson Projector Z8150NL User Manual

Network Menu
81
Wired LAN Menu
Sub Menu
Function
DHCPYou can set whether or not (On/Off) to use DHCP
g.
If this is set to On you cannot set any static IP addresses.
IP AddressYou can input the IP address
g assigned to the projector.
You can input a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
Subnet MaskYou can input the Subnet Maskg for the projector. You can...

Network Menu
82
Administrator Settings Menu
Sub Menu
Function
Administrator PasswordThis is the password for the Administrator settings menu of network settings.
You can enter up to 16 single-byte alphanumeric characters.
If the administrator password is not set, click OK with an empty password box.
Network Host NameYou can enter up to 15 single-byte alphanumeric characters.
PJLink PasswordSet a password to use when you access the projector using compatible PJLink software. sp.135
You can enter up to 32...

Network Menu
83
AMX Device DiscoveryWhen the projector is connected to a network, set this to On to allow the projector to be detected by AMX Device Discovery
g. Set 
this to Off if you are not connected to an environment controlled with a controller from AMX or AMX Device Discovery.
Crestron RoomViewSet this parameter to On only when using Crestron RoomView® to monitor and control the projector over a network. Normally, 
leave this parameter set to Off. s"About Crestron RoomView®" p.136
Changes...

Network Menu
84
Mail Notification menu
When this is set, you receive an e-mail notification if a problem or warning occurs in the projector. s"Reading Problem Mail Notification Function" 
p.131
Sub Menu
Function
Mail NotificationYou can set whether or not (On/Off) to be notified by e-mail.
SMTP ServerYou can input the IP address
g for the SMTP server for the projector.
You can input a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used.
127.x.x.x,...

Network Menu
85
Manage Certificates menu
Sub Menu
Function
Client Certificate Issued to/Issued by/Validity period
Displays the information set in the stored client certificate. It is blank if the certificate is not set. You must set the certificate if you 
use PEAP-TLS and EAP-TLS.
Select Clear to delete the stored certificate.
CA certificate Issued to/Issued by/Validity period
Displays the information set in the stored CA certificate. It is blank if the certificate is not set. You must set the...

Network Menu
86
q
Web Control is used to set certificates. s"Setting Certificates" p.129 

Network Menu
87
SNMP menu
To use SNMP to monitor the projector, you need to install the SNMP manager program on your computer. SNMP should be managed by a network 
administrator.
Sub Menu
Function
SNMPSet this parameter to On when using SNMP
g to monitor the projector.
Trap IP Address 1/Trap IP 
Address 2When SNMP is set to On, you can set up to two IP addresses as SNMP trap notification destinations.
You can input a number from 0 to 255 in each field of the address.
However, the following IP addresses...

Network Menu
88
Reset Menu
Resets all of the network settings.
Sub Menu
Function
Reset network settings.To reset all of the network settings, select Yes.
When you reset the network settings, the Passphrase, Administrator Password and Manage Certificates menu settings change back 
to their default values, and the certificates are deleted.
After you reset all the settings, the Basic menu appears. 

Info Menu (Display Only)
89
Info Menu (Display Only)
Lets you check the status of the image signals being projected and the status of the projector. Items that can be displayed vary depending on the image 
signal or input source being projected as shown in the following screen shots.
RGB Signal/Component Video
g Signal Composite video
g Signal/S-Video
g Signal LAN
Sub Menu
Function
Lamp HoursYou can display the cumulative lamp operating time
*.
When it reaches the lamp warning time, the characters are...

Info Menu (Display Only)
90
* The cumulative use time is displayed as "0H" for the first 10 hours. 10 hours and above is displayed as "10H", "11H", etc. If you are using PowerLite Pro 
Z8250NL/Z8255NL/Z8350WNL/Z8450WUNL/Z8455WUNL, the lamp operating times of both power consumption mode and normal mode are displayed. StatusThis is information about errors that have occurred on the projector.
This information may be needed if service is required.
Serial NumberDisplays the...