Epson Projector Z8150NL User Manual

Network Menu
71
Notes on Operating the Network Menu
Selecting from the top menu and sub menus, and changing of selected items are the same as operations in the configuration menu.
When done, make sure you go to the Setup complete, and select Yes, No, or Cancel. When you select Yes or No, you return to the configuration menu.
q
If the settings contain an invalid value, the settings may not take effect, even after you select Yes. Yes: Saves the settings and exits the Network menu.
No: Exits to the Network...

Network Menu
72
Soft Keyboard Operations
The Network menu contains items that require input of alphanumerics 
during setup. In this case, the following software keyboard is displayed. 
Use the [h] button on the remote control or [w/], [v/], [/ ] on the projector to move the cursor to the desired key, and 
then press the [Enter] button to enter the alphanumeric. Enter figures by 
holding down the [Num] button on the remote control, and pressing the 
numeric buttons. After inputting, press [Finish] on the...

Network Menu
73
Basic Menu
Sub Menu
Function
Projector NameDisplays the projector name used to identify the projector when connected to a network.
 When editing, you can enter up to 16 single-byte alphanumeric characters.
Web Remote PasswordSet a password to use Web Remote. You can enter up to 8 single-byte alphanumeric characters. Web Remote is a computer function 
that allows you to operate the projector by using the Web browser on a computer connected on a network. sp.127
Projector KeywordWhen set to...

Network Menu
74
Wireless LAN Menu
To connect the projector to a computer using a wireless LAN, install the Wireless LAN unit (V12H418P12). sp.190
Sub Menu
Function
Wireless LAN PowerSet this parameter to On when connecting the projector and a computer via a wireless LAN. If you do not want to connect via a 
wireless LAN, set this parameter to Off to prevent unauthorized access by others.
Wi-Fi Protected SetupWhen using a WPS (Wi-Fi Protected Setup)
g compatible access point via a wireless LAN, you can...

Network Menu
75
SSIDEnter an SSID. When an SSID is provided for the wireless WLAN network in which the projector participates, enter the SSID.
You can enter up to 32 single-byte alphanumeric characters.
Search Access PointWhen Connection Mode is set to Advanced, you can search for surrounding access points, and set the SSID to be connected from 
those access points. Depending on the access point settings, they may not be displayed in the list. You must set security separately. 
sp.76
ChannelYou can...

Network Menu
76
Search Access Point screen
Detected access points are displayed in a list.
Access points using WEP encryption cannot be connected to because this projector does not support the WEP encryption method.
Sub Menu/Icon
Function
RefreshStarts detecting access points again.
Indicates an already set access point.
Indicates the access points where security is enabled.
If you select an access point without security enabled, the Wireless LAN menu appears.
If you select an access point which has...

Network Menu
77
Security Menu (Only Available when the Optional Wireless LAN Unit Is Installed)
When the Wireless LAN unit is installed, it is strongly recommended that you set security.
q
You cannot set WEP as an encryption method for this projector.
Sub Menu
Function
SecurityYou can select a type of security.
When Quick is selected
Open: Security is not set.
WPA/WPA2-PSK (only when SSID Auto Setting is On): Communication takes place using security by WPA2. Uses AES method for 
encryption. When...

Network Menu
78
When WPA/WPA2-PSK is selected
Sub Menu
Function
PassphraseYou can enter at least 8 and up to 63 single-byte alphanumeric characters for the passphrase. When the passphrase is entered and 
the [Enter] button is pressed, the value is set and displayed as an asterisk (*).
When using it with EasyMP Network Projection, you do not need to input the passphrase in the computer if it is the initial (default) 
passphrase.
It is recommended to change the passphrase periodically for security reasons....

Network Menu
79
When WPA/WPA2-EAP is selected
PEAP/EAP-Fast PEAP-TLS/EAP-TLS LEAP
Sub Menu
Function
EAP MethodSet the protocol for authentication.
PEAP: Authentication protocol widely used in Windows Server.
PEAP-TLS: Authentication protocol used in Windows Server. Set when using client certificate.
EAP-TLS: Authentication protocol widely used for user authentication.
EAP-Fast, LEAP: Select this when these authentication protocols are used.
User nameYou can enter a user name to be used for authentication...

Network Menu
80
PasswordYou can enter an authentication password in single-byte alphanumeric characters. You can enter up to 64 characters. When the 
password is entered and the [Enter] button is pressed, the value is set and displayed as an asterisk (*).
You cannot enter more than 32 characters on the configuration menu. When setting from Web Control, you can enter more than 
32 characters.
sp.127
Client Certificate Issued to/Issued by/Validity period
Displays the information set in the stored client...