Epson Projector Z8150NL User Manual

							Network Menu
71
Notes on Operating the Network Menu
Selecting from the top menu and sub menus, and changing of selected items are the same as operations in the configuration menu.
When done, make sure you go to the Setup complete, and select Yes, No, or Cancel. When you select Yes or No, you return to the configuration menu.
q
If the settings contain an invalid value, the settings may not take effect, even after you select Yes. Yes: Saves the settings and exits the Network menu.
No: Exits to the Network menu without saving the 
settings.
Cancel: Continues displaying the Network menu. 
						

							Network Menu
72
Soft Keyboard Operations
The Network menu contains items that require input of alphanumerics 
during setup. In this case, the following software keyboard is displayed. 
Use the [h] button on the remote control or [w/], [v/], [/ ] on the projector to move the cursor to the desired key, and 
then press the [Enter] button to enter the alphanumeric. Enter figures by 
holding down the [Num] button on the remote control, and pressing the 
numeric buttons. After inputting, press [Finish] on the keyboard to 
confirm your input. Press [Cancel] on the keyboard to cancel your input.
•Each time the [CAPS] key is selected and the [Enter] button is pressed, 
it switches between uppercase and lowercase letters.
•Each time the [SYM1/2] key is selected and the [Enter] button is 
pressed, it switches the symbol keys in the section enclosed in the box. 
						

							Network Menu
73
Basic Menu
Sub Menu
Function
Projector NameDisplays the projector name used to identify the projector when connected to a network.
 When editing, you can enter up to 16 single-byte alphanumeric characters.
Web Remote PasswordSet a password to use Web Remote. You can enter up to 8 single-byte alphanumeric characters. Web Remote is a computer function 
that allows you to operate the projector by using the Web browser on a computer connected on a network. sp.127
Projector KeywordWhen set to On, you have to enter the keyword when you try to connect the projector to a computer using EasyMP Multi PC 
Projection and EasyMP Network Projection. As a result, you can prevent presentations from being interrupted by unscheduled 
connections from the computer.
Normally this should be set to On. 
						

							Network Menu
74
Wireless LAN Menu
To connect the projector to a computer using a wireless LAN, install the Wireless LAN unit (V12H418P12). sp.190
Sub Menu
Function
Wireless LAN PowerSet this parameter to On when connecting the projector and a computer via a wireless LAN. If you do not want to connect via a 
wireless LAN, set this parameter to Off to prevent unauthorized access by others.
Wi-Fi Protected SetupWhen using a WPS (Wi-Fi Protected Setup)
g compatible access point via a wireless LAN, you can easily connect the projector to the 
access point and make security settings. sp.144
Wireless LAN systemSets the wireless LAN system. Normally this should be set to 802.11b/g/n. The connection method is selected automatically 
according to the access point settings.
In an area that does not support 802.11n, only 802.11b/g is displayed.
Connection ModeSet the connection mode to use when connecting the projector and a computer via a wireless LAN.
If you select Quick, a small network is created automatically by the projector and computer. It is used with EasyMP Network 
Projection. If SSID Auto Setting is On, the projector becomes an access point. If it is set to Off, the network is created in Ad hoc 
mode
g.
If you select Advanced, the connection is established by the installed access point and Infrastructure mode
g.
SSID Auto SettingIf Connection Mode is set to Quick, when you set this to On, you can search for the projector more quickly from among multiple 
projectors. SSID is set automatically.
When connecting to multiple projectors from 1 computer in Quick mode, set this to Off, and set the same SSID in all the projectors 
that will connect. 
						

							Network Menu
75
SSIDEnter an SSID. When an SSID is provided for the wireless WLAN network in which the projector participates, enter the SSID.
You can enter up to 32 single-byte alphanumeric characters.
Search Access PointWhen Connection Mode is set to Advanced, you can search for surrounding access points, and set the SSID to be connected from 
those access points. Depending on the access point settings, they may not be displayed in the list. You must set security separately. 
sp.76
ChannelYou can select the channels used to connect in Quick mode. If interference from other signals occurs, use a different channel.
SSID DisplayTo prevent the SSID from being displayed on the LAN Standby screen, set this to Off.
DHCPYou can set whether or not (On/Off) to use DHCP
g.
If this is set to On you cannot set any more addresses.
IP AddressYou can input the IP address
g assigned to the projector.
You can input a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used. 0.0.0.0, 
127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
Subnet MaskYou can input the Subnet Maskg for the projector. You can input a number from 0 to 255 in each field of the address. However, the 
following subnet masks cannot be used.
0.0.0.0, 255.255.255.255
Gateway AddressYou can input the IP address for the gateway for the projector.
You can input a number from 0 to 255 in each field of the address. However, the following Gateway addresses
g cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
IP Address DisplayTo prevent the IP address from being displayed on the LAN Standby screen, set this to Off.
Region CodeThis is a specific string of the wireless LAN module.
Sub Menu
Function 
						

							Network Menu
76
Search Access Point screen
Detected access points are displayed in a list.
Access points using WEP encryption cannot be connected to because this projector does not support the WEP encryption method.
Sub Menu/Icon
Function
RefreshStarts detecting access points again.
Indicates an already set access point.
Indicates the access points where security is enabled.
If you select an access point without security enabled, the Wireless LAN menu appears.
If you select an access point which has security enabled, the Security menu appears. Set security according to the access point 
settings. 
						

							Network Menu
77
Security Menu (Only Available when the Optional Wireless LAN Unit Is Installed)
When the Wireless LAN unit is installed, it is strongly recommended that you set security.
q
You cannot set WEP as an encryption method for this projector.
Sub Menu
Function
SecurityYou can select a type of security.
When Quick is selected
Open: Security is not set.
WPA/WPA2-PSK (only when SSID Auto Setting is On): Communication takes place using security by WPA2. Uses AES method for 
encryption. When establishing connection from computer to projector, enter the value set in the passphrase.
When Advanced is selected
Open: Connects to access points without security enabled.
WPA/WPA2-PSK: Connects in WPA personal mode. Encryption method is selected automatically according to the access point 
settings. Set a passphrase which is the same for the access point.
WPA/WPA2-EAP: Connects in WPA enterprise mode. Encryption method is selected automatically according to the access point 
settings. Also select this item when using LEAP. 
						

							Network Menu
78
When WPA/WPA2-PSK is selected
Sub Menu
Function
PassphraseYou can enter at least 8 and up to 63 single-byte alphanumeric characters for the passphrase. When the passphrase is entered and 
the [Enter] button is pressed, the value is set and displayed as an asterisk (*).
When using it with EasyMP Network Projection, you do not need to input the passphrase in the computer if it is the initial (default) 
passphrase.
It is recommended to change the passphrase periodically for security reasons. If the network settings are initialized, it returns to the 
initial passphrase. sp.88
You cannot enter more than 32 characters on the configuration menu. When setting from Web Control, you can enter more than 
32 characters. sp.127
In Quick mode, the initial passphrase is set. 
						

							Network Menu
79
When WPA/WPA2-EAP is selected
PEAP/EAP-Fast PEAP-TLS/EAP-TLS LEAP
Sub Menu
Function
EAP MethodSet the protocol for authentication.
PEAP: Authentication protocol widely used in Windows Server.
PEAP-TLS: Authentication protocol used in Windows Server. Set when using client certificate.
EAP-TLS: Authentication protocol widely used for user authentication.
EAP-Fast, LEAP: Select this when these authentication protocols are used.
User nameYou can enter a user name to be used for authentication in single-byte alphanumeric characters (no spaces). You can enter up to 
64 characters.
If you select PEAP-TLS or EAP-TLS, the user name obtained automatically from the client certificate is displayed. You can change the 
user name, if the authentication server requires another user name.
You cannot enter more than 32 characters on the configuration menu. When setting from Web Control, you can enter more than 
32 characters.
sp.127
If you must also enter the domain name, add the domain name before user name separated by a backslash. 
						

							Network Menu
80
PasswordYou can enter an authentication password in single-byte alphanumeric characters. You can enter up to 64 characters. When the 
password is entered and the [Enter] button is pressed, the value is set and displayed as an asterisk (*).
You cannot enter more than 32 characters on the configuration menu. When setting from Web Control, you can enter more than 
32 characters.
sp.127
Client Certificate Issued to/Issued by/Validity period
Displays the information set in the stored client certificate. It is blank if the certificate is not set.
Verify Server CertificateSet whether or not to verify with the authentication server certificate to prevent illegal authentication. To select On, you must set 
a CA certificate that can verify the authentication server certificate. sp.129
CA certificate Issued to/Issued by/Validity period
Displays the information set in the stored CA certificate. It is blank if the certificate is not set.
Setting RADIUS Server 
NameSet whether or not to verify the authentication server name during server certificate verification. If you set this to On and specify 
the server name, you reduce the risk of connecting to an invalid authentication server.
RADIUS Server NameSpecify the authentication server name.
You can enter up to 32 single-byte alphanumeric characters.
Verify Exp. date of Server 
Cert.Set whether or not to verify the expiration date of the certificate during server certificate verification. If On is selected, the validity 
of the authentication server certificate is verified from the internal time of the projector.
Sub Menu
Function