Epson Projector Emp 9300 User Manual

70
Functions for Enhancing Projection Functions for Enhancing Projection
Once the settings have been made, select Preset in 
the sub-menu and then press the [Enter] button on 
the remote control or the [Auto/Enter] button on the 
projectors control panel.Select a number (1–10) for saving the settings.
Press the [Enter] button on the remote control or the 
[Auto/Enter] button on the projectors control panel to 
save the Video menu settings.
When the settings have been saved, the input resolution will...

71
Functions for Enhancing Projection Functions for Enhancing Projection
PROCEDUREWhile projecting analogue RGB images from a computer, 
press the [Preset] button on the remote control to apply 
the saved setting values for the Video menu to the 
images that are currently being projected.
The memorised preset number changes in ascending order starting 
from the lowest recording area number each time the button is 
pressed.
You must press the [Preset] button while the preset number and input 
resolution...

72
Functions for Enhancing Projection Functions for Enhancing Projection
If the input resolution is lower than the panel resolution (EMP-
9300:1400 × 1050, EMP-8300:1024 × 768)
If the input resolution is higher than the panel resolution 
(EMP-
9300:1400 × 1050, EMP-8300:1024 × 768)
Resized display Real display
The image is projected in the 
middle of the screen at the original 
input signal resolution.
Resized display Real display
The middle section of the image is 
projected. You can tilt the [ ]...

73
Functions for Enhancing Projection Functions for Enhancing Projection
You can switch the  aspect ratio
 between 4:3 and 16:9 when component 
video
 (YCbCr
 and YPbPr
), S-Video
 and composite video signals 
are being projected. Images that have been recorded in digital video and 
DVD images can be projected in 16:9 wide-screen format.
PROCEDUREThe display changes each time you press the [Resize] 
button on either the remote control or the projectors 
control panel.For SDTVWhen images that are output...

74
Functions for Enhancing Projection Functions for Enhancing ProjectionProjector ID/Remote Control ID
If using more than one projector at a time, such as at a show, you can 
record ID numbers for the projectors and for the remote controls in order to 
simultaneously operate projectors with the same ID number. Alternatively, 
if you set the remote control ID to 0, all projectors can be operated by the 
remote control regardless of the projector ID numbers.PROCEDURE
Press the [Menu] button on either the...

75
Functions for Enhancing Projection Functions for Enhancing Projection
Use the [ ] button on the remote control or the 
[Tracking +] or [Tracking -] button on the projectors 
control panel to select the desired ID number (1–9).
Press the [Enter] button on the remote control or the [Auto/
Enter] button on the projectors control panel to accept the ID 
number setting.Once the setting has been made, press the [Menu] 
button to close the configuration menu.
When the ID number is registered, the projector...

76
Functions for Enhancing Projection Functions for Enhancing Projection
TIP
If you would like to check the ID number that is currently set for a 
remote control, press the [ID] button on the remote control so that the 
button lights, and then press the [ID] button once more. After a brief 
period, the [ID] button will flash, and the number of flashes will equal 
the remote controls ID number. 

77
Using the Configuration Menu FunctionsThe configuration menus can be used to carry out a variety of settings and adjustments.
The menus have a hierarchical structure, with a main menu that is divided into sub-menus, which are further divided into other sub-menus.
Refer to Using the Configuration Menus (  p.96) for details on using the menus.
Video
Audio
Color Mode Position
Tracking
Sync.
Brightness
Contrast
Sharpness
:
: :
: :
Select 0000
     0
     0
    0
+
-+
-
Adjust
[Presentation    ]
:
:...

78
Using the Configuration Menu Functions Using the Configuration Menu FunctionsList of Functions
 The functions in the Video menu apart from Resolution and Video Signal cannot be adjusted while no video signal is being input.
 The functions which appear in the Video menu will change depending on the type of input source being projected. Functions which are not available in the 
Video menu for a particular input source cannot be adjusted.Video MenuComputer (Analogue RGB)
Computer (Digital RGB)
Video...

79
Using the Configuration Menu Functions Using the Configuration Menu Functions
Color 
ModeCorrects the vividness of the image colour. The settings can 
be saved separately for each type of source (computer or 
video source). 
You can select from five different quality settings 
depending on the surroundings.
Dynamic : Images are modulated and made fresher to 
emphasise brightness.
Presentation : Brightness is emphasized. For presentations 
in bright rooms.
Theatre : Movie images are optimised using...