Epson Projector Emp 62 User Manual

46
Problems Solving
Lamp replacement notification
Replace the lamp with a new one. sp.59
If you continue to use the lamp after it has passed the replacement period, the possibility that the 
lamp may break will increase. Replace the lamp with a new one as soon as possible. The Power 
indicator status will vary depending on the projector status at the time.
 If the projector is not operating properly even though the indicators are all showing normal, refer to When the Indicators Provide No 
Help on the...

47
Problems SolvingWhen the Indicators Provide No Help
If any of the following problems occur and the indicators do not offer a solution, refer to the pages given for each problem.
No images appear sp.48
Projection does not start, the projection area is completely black, the 
projection area is completely blue, and so on.Projection stops automatically sp.48The message Not Supported. is displayed sp.49The message No Signal. is displayed sp.49Images are fuzzy or out of focus sp.50Interference or distortion...

48
Problems Solving No images appear
 Projection stops automatically
Problems relating to images
Check
Remedy
Was the [Power] button pressed?
Press the [Power] button to turn the power on.
Are the indicators switched off?
The power cable is not connected correctly or power is not being supplied normally. Connect the 
projectors power cable correctly.  sp.iii
Check that your power supply socket is working.
Is A/V Mute mode active?
Press the [A/V Mute] button on the remote control to cancel the mute....

49
Problems Solving
 The message Not Supported. is displayed
 The message No Signal. is displayed
Check
Remedy
Are the image signal format settings 
correct?
If a composite video
g or S-Video
g source is connected to the projector, use the Video Signal menu 
command to select the signal format. Signal - Video Signal sp.35
Does the mode match the frequency and 
resolution of the image signals?
Refer to the documentation provided with your computer for details on changing the resolution and 
frequency of...

50
Problems Solving
 Images are fuzzy or out of focus
 Interference or distor tion appear in images
Check
Remedy
Has the focus been adjusted correctly?
Turn the focus ring on the projector to adjust the focus.
Is the lens cover still attached?
Remove the lens cover.
Is the projector at the correct distance?
The recommended projection distance for EMP-62 ranges from 86 cm to 1071 cm. When using EMP-82/
X3, the distance ranges from 87 cm to 1080 cm. sp.i
Is the keystone adjustment value too 
large?...

51
Problems Solving
 Image is truncated (large) or small
Check
Remedy
Has the Aspect ratio
g been set 
correctly?
Press the [Resize] button on the remote control.
 sp.21
Is the image still being enlarged by the 
E-Zoom function?
Press the [Esc] button on the remote control to cancel the E-Zoom function. sp.22
Has the Position setting been adjusted 
correctly?
If analogue RGB images from a computer or RGB video images are being projected, press the [Auto] 
button on the remote control or the [Enter]...

52
Problems Solving
 Image colours are not right
 Images appear dark
Check
Remedy
Do the input signal settings match the 
signals from the connected device?
If a composite video
g or S-Video
g source is connected to the projector, use the Video Signal menu 
command to select the video signal format.
Signal - Video Signal sp.35
Has the image brightness been adjusted 
correctly?
Use the Brightness menu command to adjust the brightness. Image - Brightness sp.33
Are the cables connected correctly?
Check that...

53
Problems Solving
 Nothing appears on the external monitor
 Power does not turn on
 No sound can be heard or the sound is faint
Check
Remedy
Are images from a port other than the 
Computer port being projected? (EMP-X3 
only)
The only images that can be displayed on an external monitor are those from the Computer port. You 
cannot output video equipment images to an external monitor. sp.66
Are images from a port other than the 
Computer1 port being projected? (EMP-
82/62 only)
The only images that can...

54
Problems Solving
 The remote control does not work
Check
Remedy
Is the remote control light-emitting area 
facing towards the remote control light-
receiving area when it is operated?
Face the remote control towards the remote control light-receiving area.
The operating angle for the remote control is approximately ±30º horizontally and approximately ±15º 
vertically. sp.i
Is the remote control too far from the 
projector?
The operating range for the remote control is approximately 6m. sp.i
Is direct...

AppendicesThis chapter provides information on maintenance procedures to ensure the best level of performance from the 
projector.Installation ........................................................... 56
• Setting Up the Projector ..................................................... 56
Maintenance ........................................................ 57
 Cleaning ............................................................................... 57• Cleaning the Projectors Surface...