Epson Projector Emp 62 User Manual

56
InstallationSetting Up the Projector
The projector supports the following four different projection methods, 
allowing you to choose the best method for displaying your images.
* A special method of installation is required for suspending the projector 
from a ceiling. Please contact your supplier if you would like to use this 
installation method. The optional ceiling mount is required when 
installing the projector on a ceiling. sp.67
 Before setting up the projector, make sure you read the...

57
MaintenanceThis section describes maintenance tasks such as cleaning the projector and 
replacing consumable parts.Cleaning
You should clean the projector if it becomes dirty or if the quality of 
projected images starts to deteriorate.
Clean the projectors surface by wiping it gently with a soft cloth.
If the projector is particularly dirty, moisten the cloth with water 
containing a small amount of neutral detergent, and then firmly wring the 
cloth dry before using it to wipe the projectors...

58
MaintenanceReplacing Consumables
This section explains how to replace the remote control batteries, the lamp, 
and the air filters.
If delays in the responsiveness of the remote control occur or if it does not 
operate after it has been used for some time, it probably means that the 
batteries are becoming flat. Replace the batteries. Have two spare AAA-
size alkali batteries ready to use when required.PROCEDUREA
Remove the battery cover.
While pushing the catch of the battery compartment cover, lift...

59
Maintenance
It is time to replace the lamp when:
The message Replace the Lamp. appears on the screen when 
projection star ts
.When the Lamp indicator is flashing orange
The projected image gets darker or starts to deteriorateLamp Replacement Period
A message will be displayed.
Flashing orange
 The lamp replacement message is set to appear after the 
following periods of time in order to maintain the initial 
brightness and quality of the projected images. 
Brightness Control sp.36
· When used...

60
Maintenance
PROCEDUREA
After you turn off the projector’s power, and the 
confirmation buzzer beeps twice, disconnect the 
power cable.
B
Wait until the lamp has cooled down, then remove the 
lamp cover from the base of the projector.
Loosen the lamp cover fixing screw with the screwdriver that is 
supplied with the spare lamp (or your own cross head 
screwdriver).
Then slide the lamp cover straight forward and lift it to remove.
C
Loosen the two lamp fixing screws.
Loosen the two lamp fixing screws...

61
MaintenanceE
Install the new lamp.
Insert the new lamp so that the lamp fits in place correctly and 
once it is fully inserted, tighten the two screws.
F
Install the lamp cover.
Slide the lamp cover and tighten the cover fixing screws.
 Install the lamp securely. If the lamp cover is removed, 
the lamp turns off automatically as a safety precaution. 
Moreover, the lamp will not turn on if the lamp or the 
lamp cover is not installed correctly.
 This product includes a lamp component that contains...

62
Maintenance
The projector has a built-in counter which keeps track of the lamp 
operating time. When the cumulative operating time reaches a certain 
point, it causes the replacement warning message to be displayed. 
Therefore, the counter needs to be reset after the lamp has been replaced 
with a new one. You can do this using the configuration menu.
PROCEDUREA
Connect the power cable and turn on the projector.
B
Select Reset from the configuration menu, and then 
select Reset Lamp Hours. 
For...

63
Maintenance
If the air filters are broken or if the warning message reappears after they 
have been cleaned, they should be replaced.
The air filter can be replaced even if the projector is installed on a ceiling.
PROCEDUREA
After you turn off the projector’s power, and the 
confirmation buzzer beeps twice, disconnect the 
power cable.
B
Remove the air filter.
Put your finger into the recess of the air filter and slide it 
forward to remove it.
C
Install the new air filter.
Slide the air filter covers...

64
Saving a Users LogoYou can record the image that is currently being projected as a users logo.
PROCEDUREA
Project the image you would like to use as the user’s 
logo, and then display the configuration menu.
B
Select Extended from the configuration menu, and 
then select User’s Logo. 
For details on this operation, refer to 
Using the Configuration 
Menu
. sp.32
Check which buttons on the remote control or the control panel 
you can use, and the operations they perform, in the guide at the 
bottom of...

65
Saving a Users LogoC
When Choose this image as the Users Logo? 
appears, select Yes.
D
The image to be recorded and a selection marquee 
box will be displayed. Move the marquee box to select 
the part of the image to use.
E
When Select this image? appears, select Yes.
F
Select the zoom rate from the Zoom rate setting 
screen.
G
When Save this image? is displayed, select Yes.
The image will then be saved. Once the image has been saved, 
the message Completed. will be displayed.
When you press the...