Epson M2000 Service Manual

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 72
Toner Cartridge
1. Open the Top Cover and the Front Cover.2. Move the Lock Lever to unlock the Toner Cartridge.3. Remove the Toner Cartridge.
A1
Toner Cartridge
Top Cover
Front Cover
Lock Lever
Front Cover
1. Slightly open the Front Cover and disengage both sides of the cover from the MP Tray by 
bowing the Guide portions of the cover.
2. Pull the Front Cover toward you to disengage its joints on both sides, and remove the cover.
B1
Guide
Joint
Joint
Front Cover
Guide 
						

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 73
Rear Cover
1. Open the Rear Cover.2. Pull out the right shaft of the Rear Cover (as seen from the rear) using a flat-blade 
screwdriver or similar tool, and remove the Rear Cover.
C1
Rear Cover
Shaft
Shaft
Paper Feed Roller (MP Tray)
1. Open the Front Cover.2. Pull the lever down ( ).3. Slide the holder out ( ).4. Remove the Paper Feed Roller ( ).
Match the shaft end with the hole for insertion of the Paper Feed Roller.
D1
Shaft
Paper Feed Roller
Hole for insertion
Shape of the Shaft end
Lever
Paper Feed Roller
Holder
Front Cover
12
3
12
3 
						

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 74
Controller Cover
1. Remove the screw.
A) Silver / M3x6 / S-Tite: One piece
2. Remove the Controller Cover in the direction of the arrow.
E1
A
Controller Cover 
						

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 754.3.2  Group 2CONTENT
Parts/Units to be Disassembled
Guide
Left CoverLVPS UnitHVPS Unit
ABC
Left Cover
A
LVPS Unit
B
HVPS Unit
C 
						

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 76DISASSEMBLY FLOWCHART
C1C2
A1B1
A1
B2
C3
Start
Left Cover(P. 77)LVPS Unit (P. 77)HVPS Unit (P. 78) 
						

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 77
Left Cover
1. Open the Top Cover.2. Slightly pull out the Paper Cassette.3. Remove the three screws.
A) Silver / M3x10 / P-Tite: Three pieces
4. Disengage the six hooks of the Left Cover in the order from the rearmost hook to the 
frontmost one, and remove the Left Cover.
A1
B1
C1Left Cover
Hooks
AA
A
LVPS Unit
1. Disconnect the four connectors connected to the LVPS Unit ( ).2. Remove the five screws and the grounding terminal.
A) Silver / M3x10 / P-Tite: Three piecesB) Silver / M3x6 / S-Tite: Two  pieces
3. Disconnect the LVPS Unit and the Power Supply Plate from the connector of the HVPS 
Unit ( ). 
B2
C2Power Supply Plate + 
LVPS Unit
A
A
A
BB
HVPS Unit
Connector  1
Connector  2
1
2 
						

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 784. Remove the four screws, and remove the LVPS Unit from the Power Supply Plate.
C) Silver / M3x6 / S-Tite: Four pieces
Make sure the Insulating Sheet is properly positioned.
C
C
C
C
Power Supply PlateLVPS Unit
Insulating Sheet
HVPS Unit
1. Put the printer upside down.2. Remove the Resin Ring.3. Remove the holder. 
C3
Resin Ring
Holder 
						

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 794. Pull out the bushing.5. Remove the cover.
Bushing
Cover
6. Remove the four screws.
A) Silver / M3x6 / P-Tite: Four pieces
7. Disengage the three hooks and remove the cover.
Hooks
AA
A
A
Cover 
						

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 808. Remove the spring from the main unit and the Cassette Pin.9. Slide the Cassette Pin to remove it.
When attaching the spring, first hitch its one end to the main frame, and then hitch the other end to the Cassette Pin.
10.Slightly lift the HVPS Unit to disconnect the two connectors, and then remove the HVPS 
Unit.
11.Remove the Cassette Pin Holder. 
Cassette Pin Holder
Cassette Pin
Connector
Spring
†
The grounding plate end should come above the HVPS Unit.
†
Make sure the Contact Pin is properly positioned.
†
The contact points on the HVPS Unit should properly contact with the springs.
OK
NG
Grounding Plate
Contact Pin
Springs 
						

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 81
Install the Cassette Pin following the procedure below.1. Insert the Cassette Pin end into the Cassette Pin Holder.2. Insert the   projection into the hole of the main unit. 
 
(At this time, do not insert the   projection) 
3. Pull the   tab in the direction of the arrow bowing the Cassette Pin, and slide the   tab toward the front side of the main unit until it passes over the projection.4. Insert the other end of the Cassette Pin into the hole on the front side of the main unit.5. Pull the   portion bowing the pin to insert the   projection into the hole of the main unit. At this time, pay attention to the followings.• The   projection must be kept inserted into the hole of the main unit.• The   tab must not go back beyond the projection.• The Cassette Pin end must be kept inserted into the hole of the main unit.
Step 5Step 1, 2
Cassette Pin Holder
Cassette Pin
Assembly Drawing
D
A
B
C
Step 3, 4
A
B
C
A
B
C
D
Projection
A
B
C
C
D
B
AC