Epson M2000 Service Manual

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 824.3.3  Group 3CONTENT
Parts/Units to be Disassembled
Guide
Developing UnitPhotoconductor UnitCharging UnitTransfer Roller
ABCD
Developing Unit
Photoconductor Unit
B
A
Charging Unit
C
Photoconductor UnitTransfer Roller
D 
						

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 83DISASSEMBLY FLOWCHART
D3
C1C2
D1D2
B1
A1
B2
C3
Start
Developing Unit
(P. 84)
Transfer Roller
(P. 85)
Charging Unit
(P. 85)
Photoconductor Unit
(P. 84) 
						

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 84
Developing Unit
1. Open the Top Cover.2. Open the Front Cover.3. Pull the Developing Unit toward you to remove it.

 	
    
The following operations must be carried out after the Developing Unit has been replaced with a new one.1. Install the toner cartridge for initial filling supplied with the Developing Unit.2. Turn the printer on while holding down [Start/Stop] and [Information] buttons. 
The printer will start up in toner filling mode.
3. When the toner filling is completed, remove the toner cartridge for initial filling, 
and install the toner cartridge in use.
A1
B1
C1
D1
Developing Unit
Top Cover
Front Cover
Photoconductor Unit
1. Pull the Photoconductor Unit toward you to remove it.
B2
C2
D2
Photoconductor Unit 
						

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 85
Charging Unit
1. While pressing the Main Plate ( ), slide the Charging Unit ( ).2. Pull the Charging Unit upward to remove it.
C3
1
2Main Plate
Charging Unit
Photoconductor Unit
Charging UnitCharging Unit
1
2
Transfer Roller
1. Slide the Paper Shoot Guide to disengage the hooks.2. Remove the Paper Shoot Guide.
D3
Paper Shoot Guide
Hooks
Paper Shoot Guide 
						

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 863. Pull the Transfer Roller Shafts from the bearings, and remove the Transfer Roller.4. Remove the gear from the Transfer Roller.
When attaching the Transfer Roller, push the release lever to lift its front end, and put the gear shaft under the front end of the lever.
Lever
Transfer Roller
Gear
Shaft
Gear
Shaft
Transfer Shaft Bearings 
						

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 874.3.4  Group 4CONTENT
Parts/Units to be Disassembled
Guide
Paper Feed Roller (Paper Cassette)Paper SensorSeparation Roller (Paper Cassette)
ABC
Paper SensorPaper Feed Roller (Paper Cassette)
AB- Bottom of Main Unit -
Separation Roller (Paper Cassette)
C 
						

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 88DISASSEMBLY FLOWCHART
A2
C1
B1
A1
C2
B2B3
Start
Paper Cassette
(P. 89)
Paper Feed Roller 
(Paper Cassette) 
(P. 89)
Paper Sensor
(P. 90)
Separation Roller 
(Paper Cassette) 
(P. 90) 
						

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 89
Paper Cassette
1. Remove the Paper Cassette.
A1
B1
C1
Paper Cassette
Paper Feed Roller (Paper Cassette)
1. Push the lever and remove the Paper Feed Roller.
Match the Feed Shaft end with the oval hole on the Paper Feed Roller.A2
B2End of the Shaft
Oval shape
Feed Shaft
Paper Feed Roller
Feed Shaft
Feed Shaft
Paper Feed Roller
Lever 
						

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 90
Paper Sensor
1. Put the printer upside down.2. Pull the Feed Shaft out in the direction of the arrow.3. Disengage the two hooks and remove the holder.4. Remove the actuator from the holder.5. Disengage the hook and remove the Paper Sensor.6. Disconnect the connector from the Paper Sensor.
B3
Feed Shaft
Actuator
Connector
Paper Sensor
Holder
Bottom
Hooks
Separation Roller (Paper Cassette)
1. Secure the Bottom Plate by pressing it down.
C2
Separation Roller
Bottom Plate
Front side 
						

							EPSON AcuLaser M2000D/M2000DN/M2010D/M2010DN Revision BDISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 912. Disengage the two hooks from the back of the cassette, and remove the Separation Roller.
Attach the spring to the projection of the separation Roller holder.
Spring
Projection
Hooks
Back side