Epson C 2900 Manual

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 97 Confidential 
 
20) Remove the ACTUATOR ASSY NO 
PAPER and the SPRING STP (PL3.2.16) 
by releasing the left shaft of the 
ACTUATOR ASSY NO PAPER from the 
hole of the CHUTE UP. 
21) Remove the SPRING STP from the 
ACTUATOR ASSY NO PAPER. 
  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 98 Confidential 
 
[Replacement] 
1) Attach the SPRING STP to the 
ACTUATOR ASSY NO PAPER. 
Note: When carrying out the work 
described next procedure, ensure that 
the SPRING STP is hung to ACTUATOR 
NO PAPER and the CHUTE UP 
correctly. 
SPRING STP
2) Insert the left shaft of the ACTUATOR 
ASSY NO PAPER into the hole of the 
CHUTE UP, hang the SPRING STP to the 
CUHTE UP.  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 99 Confidential 
 
3) Insert the right shaft of the ACTUATOR 
ASSY NO PAPER into the hole of the 
CHUTE  UP. Attach  the ACTUATOR ASSY 
NO PAPER. 
Check the ACTUATOR ASSY NO PAPER movement , after the procedure 3 is completed. 
  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 100 Confidential 
 
RRP3.13 UPPER UNIT (Reference only)   
[Removal] 
1) Remove the CASSETTE ASSY 250. (RRP2.1) 
2) Open the COVER ASSY FRONT MG (PL1.2.1). 
Note: Cover the drum of the DRUM CARTRIDGE to avoid exposure to light.  
3) Remove the DRUM CARTRIDGE. (RRP4.6)  
Note: The FUSING part is very hot. Take added care not to get burned when performing the 
service operation. 
4) Remove the FUSER UNIT. (RRP6.1) 
5) Remove...

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 101 Confidential 
 
18) Release the hook of the GUIDE 
HARNESS AC , remove the GUIDE 
HARNESS AC from the printer 
19) Release the harness of the HARN 
ASSY OPTION (PL3.1.20) from the clamp 
on the BRACKET MCU R (PL8.2.15). 
20) Remove the two screws (silver, 6mm) 
that fix the BRACKET MCU R to the 
printer.  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 102 Confidential 
 
21) Remove the BRACKET MCU R from 
the printer. 
22) Remove the two screws (silver, tap, 
8mm) that fix the front side of the printer 
frame. 
23) Remove the two screws (silver, tap, 
8mm) that fix the under part of the 
DISPENSER ASSY.  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 103 Confidential 
 
24) Open the HOLDER TCRU (K), (C), 
(M), and (Y), remove the one screw (silver, 
tap, 8mm) that fixes the right side of the 
printer frame. 
25) Remove the HARNESS ASSY B 
(PL9.1.12) and HARN ASSY OPTION 
(PL3.1.20) from the hooks of the 
DISPENSER ASSY. 
26) Remove the one screw (silver, M4, 
6mm) that fixes the rear side of the 
DISPENSER ASSY and the one screw 
(silver, tap, 8mm) that fixes the...

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 104 Confidential 
 
27) Remove the one screw (silver, tap, 
8mm) that fixes the left side of the printer 
frame and the one screw (silver, tap, 8mm) 
that fixes the BRACKET MCU L. 
28) Remove the UPPER UNIT. 
  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 105 Confidential 
 
[Replacement] 
Note: When carrying out the work 
described next procedure, route the 
harness of the TRANSFER ASSY 
through the groove of the UPPER UNIT.
1) Mate the two holes of the UPPER UNIT 
with the bosses of the FEEDER ASSY MG 
SFP and attach it. 
2) Secure the BRACKET MCU L and the 
left side of the printer frame with the two 
screws (silver, tap, 8mm).  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 106 Confidential 
 
3) Secure the rear side DISPENSER 
ASSY with the one screw (silver, M4, 
6mm) and BRACKET MCU L with the one 
screw (silver, tap, 8mm). 
4) Route the HARNESS ASSY B and the 
HARN ASSY OOPTION to the 
DISPENSER ASSY. Secure the harnesses 
using the hooks on the DISPENSER 
ASSY. 
5) Open the HOLDER TCRU (K), (C), (M) 
and (Y), secure the right side of the printer 
frame with the one screw (silver, tap,...