Epson C 2900 Manual

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 57 Confidential 
 
4) Attach the GEAR ASSY FEED to the 
SHAFT ASSY FEED by pushing down the 
LEVER FEED, mate the hook of the GEAR 
ASSY FEED with the groove of the SHAFT 
ASSY FEED. 
5) Hang the SPRING FEED OUT to the 
GEAR ASSY FEED and the printer. 
Note: Ensure that the SPRING FEED 
OUT is oriented to the direction shown 
in the right. 
6) Close the COVER ASSY FRONT MG.  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 58 Confidential 
 
7) Fit the ROLL ASSY FEED to the SHAFT 
ASSY FEED with the groove of the ROLL 
ASSY FEED facing upward, rotate the 
ROLL ASSY FEED 180 degrees so that 
the pin on the SHAFT ASSY FEED is 
aligned with the groove on the ROLL 
ASSY FEED. 
8) Open the COVER ASSY FRONT MG. 
9) Move the ROLL ASSY FEED to the right 
side, put the groove of the ROLL ASSY 
FEED on the pin of the SHAFT ASSY 
FEED.  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 59 Confidential 
 
10) Move the ROLL CORE MSI to the right 
side, to secure the hook of the ROLL 
CORE MSI with the groove of the SHAFT 
ASSY FEED. 
  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 60 Confidential 
 
RRP3.4 FEEDER ASSY MG SFP (PL3.1.98)   
[Removal] 
1) Remove the CASSETTE ASSY 250. (RRP2.1) 
2) Open the COVER ASSY FRONT MG (PL1.2.1) 
Note: Cover the drum of the DRUM CARTRIDGE to avoid exposure to light.  
3) Remove the DRUM CARTRIDGE. (RRP4.6)  
Note: The FUSING part is very hot. Take added care not to get burned when performing the 
service operation. 
4) Remove the FUSER UNIT. (RRP6.1) 
5) Remove...

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 61 Confidential 
 
20) Remove the FRAME HVPS from the 
FEEDER ASSY MG SFP together with the 
PWBA HVPS (PL4.1.19), remove the 
FEEDER 
ASSY. 
   

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 62 Confidential 
 
[Replacement] 
1) Mate the four holes of the FRAME 
HVPS with the bosses of the FEEDER 
ASSY MG SFP, attach the FRAME HVPS 
to the FEEDER ASSY MG SFP together 
with the PWBA HVPS. 
2) Secure the FRAME HVPS to the 
FEEDER ASSY MG SFP with the eight 
screws (silver, tap, 8mm). 
 
  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 63 Confidential 
 
RRP3.5 ROLL ASSY FEED (PL3.2.4)   
[Removal] 
1) Remove the CASSETTE ASSY 250. (RRP2.1) 
2) Open the COVER ASSY FRONT MG (PL1.2.1). 
Note: Cover the drum of the DRUM CARTRIDGE to avoid exposure to light. 
3) Remove the DRUM CARTRIDGE. (RRP4.6) 
4) Release the hook of the ROLL CORE 
MSI (PL3.2.3) on the left of the ROLL 
ASSY FEED (PL 3.2.4), and move the 
ROLL CORE MSI to left until it stops. 
5) Release...

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 64 Confidential 
 
7) Remove the ROLL ASSY FEED from 
the SHAFT ASSY FEED by rotating the 
ROLL ASSY FEED 180 degrees.  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 65 Confidential 
 
[Replacement] 
1) Close the COVER ASSY FRONT MG. 
2) Fit the ROLL ASSY FEED to the SHAFT 
ASSY FEED with the groove of the ROLL 
ASSY FEED facing upward, rotate the 
ROLL ASSY FEED 180 degrees so that 
the pin on the SHAFT ASSY FEED is 
aligned with the groove on the ROLL 
ASSY FEED. 
3) Open the COVER ASSY FRONT MG. 
4) Move the ROLL ASSY FEED to the right 
side, put the groove of the ROLL ASSY 
FEED on...

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 66 Confidential 
 
5) Move the ROLL CORE MSI to the right 
side, to secure the hook of the ROLL 
CORE MSI with the groove of the SHAFT 
ASSY FEED.