Epson C 2900 Manual

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 47 Confidential 
9) Remove the E-ring that fixes the 
CLUTCH ASSY DRV to the shaft, using a 
miniature screwdriver, remove the 
CLUTCH ASSY  DRV. 
10) Release the two hooks of the 
BEARING REGI (PL3.1.2), remove the 
BEARING REGI from the shaft. 
  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 48 Confidential 
[Replacement] 
1) Attach the BEARING REGI to the shaft 
of the ROLL ASSY REGI, secure the 
BEARING REGI with the hooks. 
2) Mate the notch of the CLUTCH ASSY 
DRV with the rib of the DRIVE ASSY PH, 
secure the CLUTCH ASSY DRV to the 
ROLL ASSY REGI with the E-ring by using 
a pliers. 
3) Route the harness of the CLUTCH 
ASSY DRV through the hook of the DRIVE 
ASSY PH.  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 49 Confidential 
4) Engage the connector (P/J262) of the 
CLUTCH ASSY DRV, secure the relay 
connector with the pegs of the DRIVE 
ASSY PH. 
 
  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 50 Confidential 
RRP3.2 STOPPER CST (PL3.1.10) 
[Removal] 
1) Remove the CASSETTE ASSY 250. (RRP2.1) 
2) Remove the COVER CST. (RRP1.7) 
3) Remove the one screw (silver, tap, 
8mm) that fixes the STOPPER CST 
(PL3.1.10) to the printer. 
4) Remove the STOPPER CST from the 
printer. 
  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 51 Confidential 
[Replacement] 
1) Mate the two holes of the STOPPER 
CST with the bosses of the printer, attach 
the STOPPER CST. 
2) Secure the STOPPER CST to the 
printer with the one screw (silver, tap, 
8mm). 
  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 52 Confidential 
RRP3.3 SOLENOID FEED MSI (PL3.1.11) 
[Removal] 
1) Remove the CASSETTE ASSY 250. (RRP2.1) 
2) Open the COVER ASSY FRONT MG (PL1.2.1). 
3) Open the TRANSFER ASSY (PL6.1.7). 
Note: Cover the drum of the DRUM CARTRIDGE to avoid exposure to light.  
4) Remove the DRUM CARTRIDGE. (RRP4.6)  
Note: The FUSING part is very hot. Take added care not to get burned when performing the 
service operation. 
5) Remove...

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 53 Confidential 
 
14) Release the groove on the ROLL 
ASSY FEED from the vertical pin mounted 
on the SHAFT ASSY FEED (PL3.2.2) by 
sliding the ROLL ASSY FEED to the left. 
15) Close the COVER ASSY FRONT MG. 
16) Remove the ROLL ASSY FEED from 
the SHAFT ASSY FEED by rotating the 
ROLL ASSY FEED 180 degrees. 
17) Open the COVER ASSY FRONT MG.
  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 54 Confidential 
 
18) Remove the SPRING FEED OUT 
(PL3.1.15) from the printer. 
19) Release the hook of the GEAR ASSY 
FEED (PL3.1.19), remove the GEAR 
ASSY FEED from the SHAFT ASSY FEED 
(PL3.2.2). 
Note: When carrying out the work this 
procedure, pushing down the LEVER 
FEED (PL3.1.13). 
20) Release the harness of the 
SOLENOID FEED MSI (PL3.1.11) from the 
hooks of the printer. 
Note: When carrying out the work...

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 55 Confidential 
 
21) Release the relay connector from the 
rib of the printer, disengage the connecter 
(P/J231) of the SOLENOID FEED MSI. 
22) Remove the one screw (silver, tap, 
8mm) that fixes the SOLENOID FEED MSI 
to the printer, remove the SOLENOID 
FEED MSI. 
  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 56 Confidential 
 
[Replacement] 
1) Mate the holes of the SOLENOID FEED 
MSI with the two bosses of the printer, 
secure the SOLENOID FEED MSI with the 
one screw (silver, tap, 8mm). 
2) Engage the connecter (P/J231) of the 
SOLENOID FEED MSI, secure the relay 
connector with the rib of the printer. 
3) Route the harness of the SOLENOID 
FEED MSI through the hooks of the printer.
Note: When carrying out the work described...