Epson Aculaser M4000N User Manual

AcuLaser M4000 Series Users Guide
Replacing Consumable Products131
11. Press the rEnter button, press the uUp or dDown button several times until Reset Menu 
appears on the control panel, and then press the rEnter button.
12. Press the dDown button to display Reset Fuser Counter and press the rEnter button. 
Press the dDown button to display Yes and press the rEnter button.
 

AcuLaser M4000 Series Users Guide
Cleaning and Transporting the Printer132
Chapter 6 
Cleaning and Transporting the Printer
Cleaning the Printer
The printer needs only minimal cleaning. If the printer’s outer case is dirty or dusty, turn off the 
printer and clean it with a soft, clean cloth moistened with a mild detergent.
c
Caution:
Never use alcohol or paint thinner to clean the printer cover. These chemicals can damage the 
components and the case. Be careful not to get water onto the printer...

AcuLaser M4000 Series Users Guide
Cleaning and Transporting the Printer133
Cleaning the pickup roller
1. Turn the printer off and open cover A slowly.
2. Hold the handle of the imaging cartridge and pull out.
Note:
Place the cartridge on a clean, flat surface.
 

AcuLaser M4000 Series Users Guide
Cleaning and Transporting the Printer134
3. Remove the two pick up rollers by bending their tabs slightly outwards while sliding them off 
the spindles.
4. With a clean damp cloth, wipe the pickup roller’s rubber parts.
* rubber parts
 

AcuLaser M4000 Series Users Guide
Cleaning and Transporting the Printer135
5. Reattach the pickup rollers as shown below. Then, fit the hook in the concave part of the shafts 
to fix them.
Note:
Fit the convex parts of the pickup rollers in the concave parts of the shaft.
6. Reinstall the imaging cartridge.
7. Close cover A until it clicks shut.
 

AcuLaser M4000 Series Users Guide
Cleaning and Transporting the Printer136
Transporting the Printer
Finding a place for the printer
When relocating the printer, always choose a location that has adequate space for easy operation 
and maintenance. Use the following illustration as a guide for the amount of space required around 
the printer to ensure smooth operation.
a. 20 cm
b. 25.5 cm
c. 30 cm
d. 40.2 cm
e. 20 cm
To install and use any of the following options, you will need the indicated amount of...

AcuLaser M4000 Series Users Guide
Cleaning and Transporting the Printer137
In addition to space considerations, always heed the following precautions when finding a place to 
locate the printer:
❏Place the printer where you can easily unplug the power cord.
❏Keep the entire computer and printer system away from potential sources of interference, such 
as loudspeakers or the base units of cordless telephones.
❏Avoid using an electrical outlet that is controlled by wall switches or automatic timers....

AcuLaser M4000 Series Users Guide
Cleaning and Transporting the Printer138
For short distances
Always pay attention to the following handling precautions when you need to move the printer for 
short distances.
If you are moving the printer on its own, two people should lift and carry the printer.
1. Turn off the printer and remove the following items:
❏Power cord
❏Interface cables
❏Loaded paper
❏Installed options
2. Be sure to lift the printer by the correct positions as shown below.
Note:
The rear side...

AcuLaser M4000 Series Users Guide
Troubleshooting139
Chapter 7 
Troubleshooting
Clearing Jammed Paper
If paper becomes jammed in the printer, the printer’s LCD panel and EPSON Status Monitor 
provide alert messages.
Precautions for clearing jammed paper
Be sure to observe the following points when you clear jammed paper.
❏Do not remove jammed paper by force. Torn paper can be difficult to remove and might cause 
other paper jams. Pull it gently in order to avoid tearing.
❏Always try to remove jammed...

AcuLaser M4000 Series Users Guide
Troubleshooting140
Paper Jam A (Cover A)
When a paper jam occurs in the location shown in the illustration below, the Paper Jam A message 
appears on the printer’s LCD panel.
Follow these steps to clear paper jams from cover A.
1. Open cover A.