Epson Aculaser CX28DN User Manual

Status, Error, and Service Messages 259
NO NETWORK SETTINGThe network set-
tings had not been 
completely specified 
when the machine 
was switched to 
Scan mode.Before scanning in 
Scan mode, specify 
the network settings in 
the NETWORK SET-
TING and E-MAIL 
SETTING menus.
NO SUITABLE PAPER
LOAD PAPER (xxx)Paper suitable for 
printing is not 
loaded in a paper 
tray.Load paper suitable for 
printing into a paper 
tray.
NOT INSTALLED I-UNIT
CHECK xThe indicated imag-
ing unit is not 
installed.Install...

Status, Error, and Service Messages 260
REMOVE ORIGINAL
IN ADFRThe document is 
loaded in the ADF 
while a function is 
set that requires 
scanning from the 
original glass.Place the document on 
the original glass.
RESULTS ARE OVER xxxThe LDAP search 
results exceed the 
maximum specified 
with 
MAX. 
SEARCH RESULT
 
in the LDAP SET-
TING menu.Change the maximum 
setting, or change the 
search conditions (for 
example, increase the 
length of the key-
word), and then try 
performing the LDAP 
search...

Status, Error, and Service Messages 261
TONER EMPTY
CHANGE x TONERThe indicated toner 
cartridge has 
become empty. 
(This message 
appears if 
TONER 
EMPTY 
on the 
MACHINE SET-
TING menu is set to 
STOP.)Replace the indicated 
toner cartridge.
Toner Low xThe indicated toner 
cartridge is low and 
should be replaced 
within 200 pages at 
5% coverage of Let-
ter/A4 paper.Prepare the indicated 
toner cartridge.
Trans. Belt LifeThe time to replace 
the transfer belt unit 
has been reached.Replace the...

Status, Error, and Service Messages 262
USB Hub Not supportA USB hub is con-
nected to this 
machine.This machine is not 
compatible with a USB 
hub. When connecting 
USB cables to this 
machine, do not use a 
USB hub.
USB MEMORY FULLThere is no space 
available on the 
USB memory 
device connected to 
this machine.Delete data from the 
USB memory device to 
create free space, or 
use a different USB 
memory device.
xxx COVER OPEN
CLOSE xxx COVERThe indicated cover 
is open.Close the indicated 
cover....

Status, Error, and Service Messages 263 Service Messages
These messages indicate a more serious fault that can only be corrected by a 
customer service engineer. If one of these messages appears, turn the 
machine off, then turn it on again. If the problem persists, contact your local 
vendor or authorized service provider.
xxx IS DISABLEDThe TCP/IP, FTP, 
SMTP or SMB set-
tings are disabled.Enable the TCP/IP, 
FTP, SMTP or SMB 
settings.
DESTINATION SET 
BY MANUAL UP TO 16There were more 
than 16...

Status, Error, and Service Messages 264
 

12
12Installing
Accessories
 

Introduction 266
Introduction
Note
Any damage to the machine caused by the use of accessories not 
manufactured or supported by Epson will void your warranty. 
This chapter provides information about the following accessories.
Note
The hard disk drive cannot be installed to be used at the same time. 
Installing accessories always requires that the machine and 
accessories are turned off and unplugged during installation.Dual In-Line 
Memory Module 
(DIMM)256 MB, 512 MB DIMM
(DDR2-667 SO-DIMM, 166 MHz,...

Antistatic Protection 267
Antistatic Protection
Note
It’s very important to protect the printer controller board from 
electrostatic damage while performing any task involving the controller 
board.
Turn off all power switches first. If an antistatic wrist strap is provided in 
your printer option kit, attach one end of it to your wrist and the other 
end to the bare metal chassis on the back of your printer. Never attach 
the wrist strap to any piece of equipment with an electrical current 
present....

Dual In-Line Memory Module (DIMM) 268
Dual In-Line Memory Module (DIMM)
You may need additional memory (DIMM) for complex graphics and 
for duplex (double-sided) printing.
This machine detects only half of the amount of the installed memory.
Dual in-line memory module (or DIMM) is compact circuit board with 
surface-mount memory chips.
There is 256 MB of onboard memory and one available memory 
expansion slot. The memory can be expanded to a maximum of 
768 MB (256 MB + 512MB).
Installing a DIMM
Note...