Epson Aculaser CX28DN User Manual

Dual In-Line Memory Module (DIMM) 269
2Remove the rear cover.
3Using a screwdriver, loosen the 
screw.
Do not remove any screw 
other than the one 
indicated in the 
illustration.
4Open the inside cover.
 

Dual In-Line Memory Module (DIMM) 270
5Insert the new DIMM straight 
into the DIMM connector until 
the latches snap into the locked 
position.
Observe the keyed side of the 
DIMM to align it with the connec-
tor. If you cannot snap the DIMM 
into place, do not force it. Repo-
sition it, making sure that the 
DIMM is seated completely in 
the connector.
6Close the inside cover, and then tighten the screw.
7Close the rear cover.
8Reconnect all interface cables.
9Reconnect the power cord, and 
turn on the...

Hard Disk Drive 271
Hard Disk Drive
If you install a hard disk drive, the followings can be performed:
„Job printing/saving
„Fonts/forms/color profile download
„User Authentication
„Direct printing
Installing the Hard Disk drive
Note
Its very important to protect the printer controller board and any 
associated circuit boards from electrostatic damage. Before performing 
this procedure, review the antistatic caution on page 267. In addition, 
always handle circuit boards by the edges only.
1Turn off the...

Hard Disk Drive 272
2Remove the rear cover.
3Using a screwdriver, loosen the 
screw.
Do not remove any screw 
other than the one indicated 
in the illustration.
4Open the inside cover.
 

Hard Disk Drive 273
5Plug the cable on the hard disk 
drive into the connector on the 
controller board.
6Insert the three mounting pins 
on the hard disk drive into the 
holes in the controller board to 
mount the hard disk drive onto 
the controller board.
7Close the inside cover, and then tighten the screw.
8Close the rear cover.
9Reconnect all interface cables.
 

Hard Disk Drive 274
10Reconnect the power cord, and 
turn on the machine.
11Declare the Hard Disk in the Windows printer driver (Properties/Configure 
tab).
 

Tray 3 (Lower Feeder Unit) 275
Tray 3 (Lower Feeder Unit)
You can install up to one optional lower feeder unit (Tray 3). The lower feeder 
unit increases your machine’s media feed capacity by 500 sheets. 
Kit Contents
„Lower feeder unit with a tray (500-sheet capacity)
 

Tray 3 (Lower Feeder Unit) 276
Installing Tray 3
Note
Since consumables are installed in the machine, be sure to keep the 
machine level when moving it in order to prevent accidental spills.
1Turn off the machine and discon-
nect the power cord and inter-
face cables.
2Prepare the lower feeder unit.
Be sure to place the lower feeder unit on a level surface.
3Open the right side cover of the 
lower feeder unit.
The right side cover of the lower feeder must be opened before the 
feeder can be installed...

Tray 3 (Lower Feeder Unit) 277
4With another person’s help, 
place the machine on top of the 
lower feeder unit, making sure 
that the positioning pins on the 
lower feeder unit correctly fit into 
the holes on the bottom of the 
machine.
WARNING!
This machine weighs approximately 55 kg (121 lb) when it is fully 
loaded with consumables. The machine must be lifted by two people.
5Close the right side cover of the 
lower feeder unit.
6Reconnect all interface cables.
55 kg121 lbs
 

Tray 3 (Lower Feeder Unit) 278
7Reconnect the power cord, and 
turn on the machine.
8Declare the Tray 3 in the Windows printer driver (Properties/Configure 
tab).