Epson Aculaser CX16NF User Manual

8. Pull down the handle on the toner cartridge until the toner cartridge is unlocked and moves out
slightly toward you.
Remove the toner cartridge.
Note:
Do not manually rotate the toner cartridge carousel. In addition, do not rotate the carousel with
force, otherwise it may be damaged.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Replacing Consumables     121
 

Note:
❏Do not touch the contact indicated in the illustration.
❏Dispose of the empty toner cartridge according to your local regulations. Do not burn the toner
cartridge.
For details, refer to “About Toner Cartridges” on page 117.
9. Check the color of the new toner cartridge to be installed.
10. Remove the toner cartridge from the bag.
11. Shake the cartridge a few times to distribute the toner.
Note:
Make sure that the toner roller cover is securely attached before shaking the toner cartridge.
AcuLaser...

12. Remove the cover from the toner roller.
Note:
Do not touch or scratch the toner roller.
13. Align the shaft on each end of the toner cartridge with its holders, and then insert the cartridge.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Replacing Consumables     123
 

Note:
Before inserting the toner cartridge, make sure that the color of the toner cartridge to be installed is
the same as the label on the toner cartridge carousel.
Note:
Do not touch the contact indicated in the illustration.
14. Press in the toner cartridge until it locks into place.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Replacing Consumables     124
 

15. Close the front cover.
16. Press the Stop/Reset key to reset the machine and clear the indicator message.
Note:
The machine must complete a calibration cycle after a toner cartridge has been replaced. If you open
the scanner unit or front cover before the machine is reset, the calibration stops, then starts over again
after the cover is closed.
Removing All Toner Cartridges
Note:
Be careful not to spill toner while removing a toner cartridge. If toner spills, immediately wipe it off with a
soft, dry...

4. Open the front cover.
Note:
Before opening the front cover, open Tray 1 if it is not already open.
5. Pull down the handle on the toner cartridge until the toner cartridge is unlocked and moves out
slightly toward you.
Remove the toner cartridge.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Replacing Consumables     126
 

Note:
Do not manually rotate the toner cartridge carousel. In addition, do not rotate the carousel with
force, otherwise it may be damaged.
Note:
Do not touch the contact indicated in the illustration.
6. Close the front cover.
Note:
To exit EJECT MODE, press the Stop/Reset key.
7. Follow the same procedure to remove the cartridges for the cyan, black, then yellow toners.
8. Press the Stop/Reset key to reset the machine.
Replacing the Photoconductor Unit
Part Name Photoconductor Unit Part Number...

1. Open the scanner unit.
Note:
If there is paper in the output tray, remove it, and then fold up the output tray before opening the
scanner unit.
Note:
Do not touch the wires and flat cable shown in the illustration.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Replacing Consumables     128
 

2. Grab the handle and lift it up slightly to the back, and then slowly pull the photoconductor unit out
vertically.
Note:
Dispose of the used photoconductor unit according to your local regulations. Do not burn the
photoconductor unit.
3. Prepare the new photoconductor unit.
Note:
Do not touch the PC drum and the transfer belt on the photoconductor unit.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Replacing Consumables     129
 

4. Slowly insert the new photoconductor unit vertically, and then push it slightly down toward you to
finish installing the photoconductor unit.
5. Carefully close the scanner unit.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Replacing Consumables     130