Epson Aculaser CX16NF User Manual

9. Clean the print head window by wiping it with a soft, dry cloth.
c
Caution:
The area around the fuser unit is extremely hot.
Touching anything other than the indicated levers may result in burns. If you get burned,
immediately cool the skin under cold water, and then seek professional medical attention.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Maintenance     151
 

Note:
Decreased print quality may result if the surface of the transfer roller is touched.
Be careful not to touch the surface of the transfer roller.
10. Slowly insert the photoconductor unit vertically, and then push it slightly down toward you to
finish reinstalling the photoconductor unit.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Maintenance     152
 

11. Close the scanner unit.
Note:
Do not touch the wires and flat cable shown in the illustration.
12. Press the Stop/Reset key.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Maintenance     153
 

13. After the toner cartridges have finished rotating, open the front cover.
14. Align the shaft on each end of the toner cartridge with its holders, and then insert the cartridge.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Maintenance     154
 

Note:
Do not touch the contact indicated in the illustration.
15. Press in the magenta toner cartridge until it locks into place.
16. Close the front cover.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Maintenance     155
 

Long-term storage of the printer
If the printer will not be used for a month or more, install the protective materials onto the fuser unit.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Maintenance     156
 

Chapter 9
Troubleshooting
Introduction
This chapter provides information to aid you in resolving machine problems you may encounter, or at
least guide you to the proper sources for help.
Printing a Configuration Page
1. In the main screen, press the u or d key to select REPORT/STATUS, and then press the Select
key.
2. Press the u or d key to select REPORT, and then press the Select key.
3. Press the u or d key to select CONFIGURATION PAGE, and then press the Select key.
4. Press the Start-B&W key or the...

Avoid...
Media that is folded, wrinkled, or excessively curled.
Double feeding (remove the media and fan the sheets—they may be sticking together).
Loading more than one type/size/weight of media in a tray at the same time.
Overfilling the trays.
Allowing the output tray to overfill (the output tray has a 100 sheet capacity—misfeeding may occur if you allow more than
100 sheets of media to accumulate at one time).
Clearing Media Misfeeds
To avoid damage, always remove misfed media gently, without tearing...

Media Misfeed Messages and Clearing Procedures
Media Misfeed Message Page Reference
CHECK TRAY1 PAPER
LOAD PAPER (
1xx)
(PRESS START KEY)This message appears in the following cases.
❏When no media is loaded in Tray 1
❏When a misfeed has occurred in Tray 1
With the first case, load media into the tray, and then press the Start key.
With the second case, refer to “Clearing a Media Misfeed From Tray 1” on
page 169.
FUSER JAM
OPEN TOP COVER“Clearing a Media Misfeed in the Machine” on page 160
ORIGINAL DOC....

Clearing a Media Misfeed in the Machine
1. Open the scanner unit.
Note:
If there is paper in the output tray, remove it, and then fold up the output tray before opening the
scanner unit.
Note:
Do not touch the wires and flat cable shown in the illustration.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Troubleshooting     160