Epson Aculaser CX16NF User Manual

This message... means... Do this...
SEARCHINGThe machine is searching data. No action needed.
SCANNINGThe machine is scanning the document.
Warming UpThe machine is warming up or AIDC is
being performed.
REFRESHING
PLEASE WAIT!The printer is adjusting the toner
distribution.
Error Messages
Note:
For details on fax error messages, refer to the Facsimile User’s Guide. (AcuLaser CX16NF only)
This message... means... Do this...
ADDRESS IS TOO LONGThe e-mail address retrieved
from the LDAP server exceeds
64...

This message... means... Do this...
COMMUNICATION ERROR
xxx ServerWhile data was being sent in
Scan mode, the connection to
the server was interrupted.Check the settings specified in the
NETWORK SETTING and E-MAIL
SETTING menus, and then try
sending the data again.
DISCONNECT
USB MemoryThe connection to the USB
memory device was
interrupted.Check the connection to the USB
memory device, and then try
sending the data again.
DISCONNECT
xxx ServerThe connection to the server
was interrupted.Check the...

This message... means... Do this...
MEMORY FULLThe machine has received
more data than can be
processed with its internal
memory.Turn the machine off, and then,
after a few seconds, turn it on
again. Decrease the amount of
data to be printed (for example, by
decreasing the resolution), and
then try printing again.
NO NETWORK SETTINGThe network settings had not
been completely specified
when the machine was
switched to Scan mode.Before scanning in Scan mode,
specify the network settings in the
NETWORK...

This message... means... Do this...
NOT REGISTEREDNo speed dial destination or
group dial destination is
registered.
Otherwise, no destination has
been registered with the
specified speed dial or group
dial number.Directly type in the destination
address for the scan data, or
register a speed dial destination or
group dial destination and try
specifying the destination address
again.
OUTPUT TRAY FULL
REMOVE PAPERThe output tray is full of paper.Remove all paper from the output
tray.
OVER SEARCH...

This message... means... Do this...
RETURN xx ORIGINAL to ADF and PRESS
START KEYAfter a media misfeed has
been cleared from the ADF,
the number of document
pages to be reloaded into the
ADF is indicated.Reload into the ADF the number of
document pages indicated by xx,
and then press the Start key.
SERVER MEMORY FULL
SMTP ServerThe memory of the SMTP
server has become full.Free up some space on the disk, for
example, by contacting your server
administrator.
THE PARTY IS FULLThe maximum number of 236...

This message... means... Do this...
USB Dev.Not supportA USB device incompatible
with this machine is
connected.Disconnect the USB device from
this machine.
USB Hub Not supportA USB hub is connected to this
machine.This machine is not compatible
with a USB hub. When connecting
USB cables to this machine, do not
use a USB hub.
USB MEMORY FULLThere is no space available on
the USB memory device
connected to this machine.Delete data from the USB memory
device to create free space, or use a
different USB...

Service Messages
These messages indicate a more serious fault that can only be corrected by a customer service engineer.
If one of these messages appears, turn the machine off, then turn it on again. If the problem persists,
contact your local vendor or authorized service provider.
This service message... means... Do this...
MACHINE TROUBLE
SERVICE CALL (xxxx)An error has been detected
with the item indicated “xxxx”
in the service message.Reboot the machine. This often
clears the service message, and...

Chapter 10
Installing Accessories (AcuLaser CX16NF only)
Introduction
Note:
Any damage to the machine caused by the use of accessories not manufactured or supported by Epson
will void your warranty.
This chapter provides information about the following accessories.
Tray 2
Duplex Option and
AttachmentAuto duplexing
Note: 
The attachment is an interface unit for installing the duplex option on the machine.
During installation, install the attachment before installing the duplex option.
Note:
Installing...

Kit Contents
❏500-sheet paper cassette unit with a tray
Installing Tray 2
Note:
Since consumables are installed in the machine, be sure to keep the machine level when moving it in order
to prevent accidental spills.
1. Turn off the machine and disconnect the power cord and interface cables.
2. Remove the dust cover from Tray 1.
Close Tray 1 and the output tray.
3. Prepare the 500-sheet paper cassette unit.
Note:
Be sure to place the 500-sheet paper cassette unit on a level surface.
AcuLaser CX16 Series...

4. Lift the machine and place it on top of the 500-sheet paper cassette unit, making sure that the
positioning pins on the 500-sheet paper cassette unit correctly fit into the holes on the bottom of
the machine.
w
Warning:
This machine weighs approximately 21 kg (46 lb) when it is fully loaded with consumables.
5. Open Tray 1 and reattach the dust cover.
6. Load paper into Tray 2.
For details on loading paper, refer to “Tray 2” on page 62.
7. Insert Tray 2 into the machine.
AcuLaser CX16 Series...