Eiki Projector Lc Wxl200al User Manual

71

Unplug the AC power cord before cleaning.
Gently wipe the projection lens with a cleaning cloth that 
contains a small amount of non-abrasive camera lens cleaner, 
or use a lens cleaning paper or commercially available air 
blower to clean the lens. 
Avoid using an excessive amount of cleaner. Abrasive 
cleaners, solvents, or other harsh chemicals might scratch the 
surface of the lens.
Unplug the AC power cord before cleaning.
Gently wipe the projector body with a soft dry cleaning cloth. 
When the...

72

The WARNING indicators show the state of the function which protects the proj\
ector. Check the state of the WARNING 
indicators and the POWER indicator to take proper maintenance. 
The	projector	is	shut	down	and	the	WARNING	
TEMP .	indicator	is	blinking	red .
When the temperature inside the projector reaches a
certain level, the projector will be automatically shut down to 
protect the inside of the projector. The POWER indicator is blinking 
while the projector is being cooled down. When the...

7

Before calling your dealer or service center for assistance, check the i\
tems below once again.
1. Make sure you have properly connected the projector to peripheral equipment as described on pages 19-21.
2. Check the cable connection. Make sure that all computers, video equipment, and power cords are properly connected.
3. Make sure that all power is switched on.
4. If the projector still does not produce an image, restart your computer.
5. If an image still does not appear, disconnect the...

74

appears	on	the	screen
–  Filter is out of scroll. Replace the filter cartridge with a new one promptly.  (See pages 
67-68)
The	image	is	out	of	focus .
– Adjust the focus of the projector.
– Check Projection Lens to see if it needs cleaning.
 Note:  Moving	the	projector	from	a	cool	temperature	location	to	a	warm	temperature	
location	may	result	in	moisture	condensation	on	Projection	Lens.	In	such	
cases,	leave	the	projector	OFF 	and	wait	until	condensation	evaporates.
–   Projecting  from...

75

WARNING:	
High	voltages	are	used	to	operate	this	projector .	Do	not	attempt	to	open	the	cabinet .
If  problems  still  persist  after  following  all  operating  instructions,  contact  the  dealer  where  you  purchased  the  projector  or  the 
service center. Specify the model number and explain about the problem. We will advise you how to obtain service.
Appendix
The	power	is	turned	off	
automatically .
–  Power  management  function  runs  by  initial  setting.  Check  “Setting”  section  on...

76

InputRGB (PC analog)
Y, Pb/Cb,Pr/Cr
RGB (Scart)
HDMI
Network
Video
RGB
Video
Y, Pb/Cb,Pr/Cr
S-video
Input 3
InputH-sync freq.V-sync freq.
Information
ScreenLanguageLamp status
Power management
Remote control
Note:
		The	Menu	display	varies	depending	on	the	input	signal.
Appendix
Volume
MuteOn/Off
Sound0-63
Built-in SP
PIN code lock
Key lock
SERIAL NO.
Network will be displayed only when an optional Network unit is attached.
*
*
Input 1
Input 2
Lamp counterFilter counter
Simple mode
On/Off
System...

77

Note:
	The	Menu	display	varies	depending	on	the	input	signal.
System	(2)Auto
PAL
SECAM
NTSC
NTSC 4.43
PAL-M
PAL-N
System	(3)Auto
1080i
1035i
720p
575p
480p
575i
480i
Image	select
Cinema
Appendix
ScreenNormal
Wide(16:9)Full
Zoom
Rear
Keystone
CeilingResetStore
On/OffOn/Off
Custom adj.H & VScale
Position
H / VOn/OffH / VCommonReset
Reset
Screen
Digital zoom +
Digital zoom -
Video	InputImage	select
Screen
Image	adjustContrastBrightness
Color temp.
Red
Gamma
Store
0–630–63
0–63
0–15
Image 1
Image 10...

7

SettingLanguage
Fan control
Blue/User/Black
Yes/No
12 languages provided.
Menu position
Lamp control
Filter control
All/Front&Top/Top&Back/Front&Back/Front/Top/Back
Normal/Max
Power management
Background
RC sensor
Ready
Off
Shut down
1–30 Min
On/OffDirect onPointer
On/Countdown Off/OffDisplay
Remote Control
Finger/Arrow/Dot
Appendix
Yes/NoFactory default
ShutterProtection
Management
Remote controlOn/Off
ProjectorOn/Off
5 - 480 Min.
Code 1~Code 8
On/Off
Computer	Input/HDMI	Input/Video	Input
Logo...

79

Check the indicators for the projector condition.  
Indicators
Projector	ConditionPOWER
green
LAMP
red
WARNINGTEMP.
red
WARNINGFILTER
orange
SHUTTER
blue
LAMPREPLACE
orange
The projector is off. (The AC power cord is unplugged.)
The projector is in stand-by mode. Press the ON/
STAND-BY button to turn on the projector.
The projector is operating normally.
(The shutter is open)
The projector is operating normally.
(The shutter is closed)
The projector is preparing for stand-by or the projection 
lamp...

0

The	projector	is	detecting	abnormal	condition .
Indicators
Projector	ConditionPOWER
green
LAMP
red
WARNINGTEMP.
red
WARNINGFILTER
orange
SHUTTER
blue
LAMPREPLACE
orange
The temperature inside the projector is elevated close to the 
abnormally high level.
The temperature inside the projector is abnormally high. The 
projector cannot be turned on. When the projector is cooled 
down enough and the temperature returns to normal, the 
POWER indicator lights green and the projector can be turned 
on....