Eiki Projector Lc Wxl200al User Manual
Here you can view all the pages of manual Eiki Projector Lc Wxl200al User Manual. The Eiki manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 81
![Page 81
1
The projector is detecting abnormal condition .
Indicators
Projector ConditionPOWER
green
LAMP
red
WARNINGTEMP.
red
WARNINGFILTER
orange
SHUTTER
blue
LAMPREPLACE
orange
If the Filter counter reached a time set in the timer setting, a Filter \
replacement icon (Fig.2) appears on the screen and the WARNING
FILTER indicator on the top panel lights up. Replace the filter as
soon as possible. If the filter is out of scroll and the projector reach\
es
a time set in the timer setting, Fig. 3...](http://img.usermanuals.tech/thumb/1702/88947/w300_eiki-lc-wxl200al-manual_d-80.png "Page 81
1
The projector is detecting abnormal condition .
Indicators
Projector ConditionPOWER
green
LAMP
red
WARNINGTEMP.
red
WARNINGFILTER
orange
SHUTTER
blue
LAMPREPLACE
orange
If the Filter counter reached a time set in the timer setting, a Filter \
replacement icon (Fig.2) appears on the screen and the WARNING
FILTER indicator on the top panel lights up. Replace the filter as
soon as possible. If the filter is out of scroll and the projector reach\
es
a time set in the timer setting, Fig. 3...")
1 The projector is detecting abnormal condition . Indicators Projector ConditionPOWER green LAMP red WARNINGTEMP. red WARNINGFILTER orange SHUTTER blue LAMPREPLACE orange If the Filter counter reached a time set in the timer setting, a Filter \ replacement icon (Fig.2) appears on the screen and the WARNING FILTER indicator on the top panel lights up. Replace the filter as soon as possible. If the filter is out of scroll and the projector reach\ es a time set in the timer setting, Fig. 3...
Page 82
2 ON-SCREEN DISPLAyRESOLUTIONH-Freq . (kHz)V-Freq .(Hz) VGA 1640x48031.470 59.880 VGA 2720x40031.470 70.090 VGA 3640x40031.470 70.090 VGA 4640x48037.860 74.380 VGA 5640x48037.860 72.810 VGA 6640x48037.500 75.000 VGA 7640x48043.269 85.000 MAC LC13640x48034.970 66.600 MAC 13640x48035.000 66.670 480p640x48031.470 59.880 575p768x57531.250 50.000 575i768x576(Interlace)15.62550.000 480i640x480(Interlace)15.73460.000 SVGA 1800x60035.156 56.250 SVGA 2800x60037.880 60.320 SVGA 3800x60046.875...
Page 83
![Page 83
Appendix
When the input signal is digital from HDMI terminal, refer to the chart \
below.
Note:
•Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed.•Specifications are subject to change without notice.•You might be able to project images even when signals other than above are inputted, however the functions of the
projector could be limited.•Depending on your PC settings, the digital signals of your PC may not be projected...](http://img.usermanuals.tech/thumb/1702/88947/w300_eiki-lc-wxl200al-manual_d-82.png "Page 83
Appendix
When the input signal is digital from HDMI terminal, refer to the chart \
below.
Note:
•Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed.•Specifications are subject to change without notice.•You might be able to project images even when signals other than above are inputted, however the functions of the
projector could be limited.•Depending on your PC settings, the digital signals of your PC may not be projected...")
Appendix When the input signal is digital from HDMI terminal, refer to the chart \ below. Note: •Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed.•Specifications are subject to change without notice.•You might be able to project images even when signals other than above are inputted, however the functions of the projector could be limited.•Depending on your PC settings, the digital signals of your PC may not be projected...
Page 84
![Page 84
4
Mechanical Information
Projector Type Multi-media Projector
Dimensions (W x H x D) 19.25” x 6.46” x 17.12” (489.5 mm x 164.0 mm x 434.8 mm)
Net Weight 21.3 lbs (\
9.7 kg)
Feet Adjustment 0˚ to 4˚
Panel Resolution
LCD Panel System 0.75” TFT Active Matrix type, 3 panels
Panel Resolution 1,280 x 800 dots
Number of Pixels 3,072,000 (1,280 x 800 x 3 panels)
Signal Compatibility
Color System PAL,...](http://img.usermanuals.tech/thumb/1702/88947/w300_eiki-lc-wxl200al-manual_d-83.png "Page 84
4
Mechanical Information
Projector Type Multi-media Projector
Dimensions (W x H x D) 19.25” x 6.46” x 17.12” (489.5 mm x 164.0 mm x 434.8 mm)
Net Weight 21.3 lbs (\
9.7 kg)
Feet Adjustment 0˚ to 4˚
Panel Resolution
LCD Panel System 0.75” TFT Active Matrix type, 3 panels
Panel Resolution 1,280 x 800 dots
Number of Pixels 3,072,000 (1,280 x 800 x 3 panels)
Signal Compatibility
Color System PAL,...")
4 Mechanical Information Projector Type Multi-media Projector Dimensions (W x H x D) 19.25” x 6.46” x 17.12” (489.5 mm x 164.0 mm x 434.8 mm) Net Weight 21.3 lbs (\ 9.7 kg) Feet Adjustment 0˚ to 4˚ Panel Resolution LCD Panel System 0.75” TFT Active Matrix type, 3 panels Panel Resolution 1,280 x 800 dots Number of Pixels 3,072,000 (1,280 x 800 x 3 panels) Signal Compatibility Color System PAL,...
Page 85
![Page 85
5
The lens of this projector can be replaced with other optional lens. This feature enables you to use the projector for wide variety of uses.For installation and replacement of the lens, always contact the sales d\
ealer. The projector lens must be installed or replaced by well-trained sales or service engineers. Do not attempt to install an\
d replace the lens by yourself as it may cause injury.
Do not hold the lens when carrying or lifting the projector. It may cause serious damage to the...](http://img.usermanuals.tech/thumb/1702/88947/w300_eiki-lc-wxl200al-manual_d-84.png "Page 85
5
The lens of this projector can be replaced with other optional lens. This feature enables you to use the projector for wide variety of uses.For installation and replacement of the lens, always contact the sales d\
ealer. The projector lens must be installed or replaced by well-trained sales or service engineers. Do not attempt to install an\
d replace the lens by yourself as it may cause injury.
Do not hold the lens when carrying or lifting the projector. It may cause serious damage to the...")
5 The lens of this projector can be replaced with other optional lens. This feature enables you to use the projector for wide variety of uses.For installation and replacement of the lens, always contact the sales d\ ealer. The projector lens must be installed or replaced by well-trained sales or service engineers. Do not attempt to install an\ d replace the lens by yourself as it may cause injury. Do not hold the lens when carrying or lifting the projector. It may cause serious damage to the...
Page 86
6 ANALOG/ ANALOG OUT (Mini D-sub 15 pin) 512341096781514131112 CONTROL PORT CONNECTOR (D-sub 9 pin) ----- R X D T X D ----- SG ----- RTS CTS Serial 1 2 4 5 6 7 Vcc - Data + Data Ground 1 2 4 USB CONNECTOR (Series B) 2 3 4 1 Appendix -----9 Red Input Ground (Horiz.sync.) Green Input No Connect Blue Input Ground (Red) Ground (Green) Ground (Blue) 1 5 2 4 6 7 Horiz. sync. Input (Composite H/V sync.) Ground (Vert.sync.) DDC Data Ground Vert. sync. Input DDC Clock 9...
Page 87
![Page 87
7
Write down the PIN code number in the column below and keep it with this \
manual securely. If you forgot or lost
the number and unable to operate the projector, contact the service center.
Factory default set No: 1 2 4*
Factory default set No: 4 2 1*
* S h o u l d t h e f o u r - d i g i t n u m b e r b e
changed, the factory set number will
be invalid.
Put the label below (supplied) on in a prominent place of
the projector’s body while it is locked with a PIN...](http://img.usermanuals.tech/thumb/1702/88947/w300_eiki-lc-wxl200al-manual_d-86.png "Page 87
7
Write down the PIN code number in the column below and keep it with this \
manual securely. If you forgot or lost
the number and unable to operate the projector, contact the service center.
Factory default set No: 1 2 4*
Factory default set No: 4 2 1*
* S h o u l d t h e f o u r - d i g i t n u m b e r b e
changed, the factory set number will
be invalid.
Put the label below (supplied) on in a prominent place of
the projector’s body while it is locked with a PIN...")
7 Write down the PIN code number in the column below and keep it with this \ manual securely. If you forgot or lost the number and unable to operate the projector, contact the service center. Factory default set No: 1 2 4* Factory default set No: 4 2 1* * S h o u l d t h e f o u r - d i g i t n u m b e r b e changed, the factory set number will be invalid. Put the label below (supplied) on in a prominent place of the projector’s body while it is locked with a PIN...
Page 88
Appendix Dimensions Appendix Unit: inch (mm) 3.31(84.0) 16.39(416.2) 6.46(164.0)5.91(150.0) 19.27(489.5) 7.25(184.2) 3.34(84.7) 6.67(169.5)14.61(371.1) 6.25(158.8) 5.91(150.0) 6.89(175.0) 2.95(75.0)1.18(30.0) 7.70(195.5) 3.78(96.0) 6.30(160.0)17.12(434.8) 3.80(96.6)4.34(110.3) 9.20(233.6) 4q 13.58(344.9) Screw Holes for Ceiling Mount Screw: M6 Depth: 0.393 (10.0)
Page 89
![Page 89
9
Appendix
This projector provides a function to control and monitor the projector'\
s operations by using the RS-232C serial port.
Connect a RS-232C serial cross cable to CONTROL PORT
on the projector and serial port on the PC. (See p.19)
Launch a communication software provided with PC and
setup the communication condition as follows:
1
2
Baud rate : 9600 / 19200 bps
Parity check : none
Stop bit : 1
Flow control : none
Data bit : 8
Type the command for controlling the projector...](http://img.usermanuals.tech/thumb/1702/88947/w300_eiki-lc-wxl200al-manual_d-88.png "Page 89
9
Appendix
This projector provides a function to control and monitor the projector'\
s operations by using the RS-232C serial port.
Connect a RS-232C serial cross cable to CONTROL PORT
on the projector and serial port on the PC. (See p.19)
Launch a communication software provided with PC and
setup the communication condition as follows:
1
2
Baud rate : 9600 / 19200 bps
Parity check : none
Stop bit : 1
Flow control : none
Data bit : 8
Type the command for controlling the projector...")
9 Appendix This projector provides a function to control and monitor the projector'\ s operations by using the RS-232C serial port. Connect a RS-232C serial cross cable to CONTROL PORT on the projector and serial port on the PC. (See p.19) Launch a communication software provided with PC and setup the communication condition as follows: 1 2 Baud rate : 9600 / 19200 bps Parity check : none Stop bit : 1 Flow control : none Data bit : 8 Type the command for controlling the projector...
Page 90
![Page 90
90
The command is sent from PC to the projector with the
format below;
'C' [Command] 'CR'
Command: two characters (refer to the command
table below.
-The projector decodes the command and returns the 'ACK'
with the format below;
'ACK' 'CR'
-When the projector can not decode the command, it returns
with format below.
‘?’ ‘CR’
Format
Appendix
Functional Execution Command
CommandFunction
C00Turn the projector ON
C01Turn the...](http://img.usermanuals.tech/thumb/1702/88947/w300_eiki-lc-wxl200al-manual_d-89.png "Page 90
90
The command is sent from PC to the projector with the
format below;
'C' [Command] 'CR'
Command: two characters (refer to the command
table below.
-The projector decodes the command and returns the 'ACK'
with the format below;
'ACK' 'CR'
-When the projector can not decode the command, it returns
with format below.
‘?’ ‘CR’
Format
Appendix
Functional Execution Command
CommandFunction
C00Turn the projector ON
C01Turn the...")
90
The command is sent from PC to the projector with the
format below;
'C' [Command] 'CR'
Command: two characters (refer to the command
table below.
-The projector decodes the command and returns the 'ACK'
with the format below;
'ACK' 'CR'
-When the projector can not decode the command, it returns
with format below.
‘?’ ‘CR’
Format
Appendix
Functional Execution Command
CommandFunction
C00Turn the projector ON
C01Turn the...