Eiki Projector Lc Wxl200al User Manual

51

Setting
Setting	Menu
Press the MENU button to display the On-Screen Menu.  
Press the Point ▲▼ buttons to select Setting and press the 
Point ► or the SELECT button to access the submenu items.
1
2Use the Point ▲▼ buttons to select the desired item and 
then press the Point ► or the SELECT button to access the 
selected item.
This projector has a Setting menu that allows you to set up the 
other various functions described below.
Use the Point ▲▼ buttons to select the desired item and 
then...

52

This function decides whether to display On-Screen Displays.
 On ...............................  Show all the On-Screen displays. Use this 
function when you want to project images 
after the lamp becomes bright enough. The 
factory default setting is in this option.
 Countdown	Off ..........  Show the input image instead of the 
countdown when turning on the projector. 
Use this function when you want to project 
the image as early as possible even when 
the lamp is not bright enough.
 Off...

5

Setting
Capture
Capture
This function enables you to capture an image being projected to 
use it for a starting-up display or interval of presentations.
Select	Capture and press the SELECT button.  
A confirmation box appears and select yes to capture the projected 
image.
After capturing the projected image, go to the Logo select function 
and set it to User. Then the captured image will be displayed the 
next time you turn on the projector.
To cancel the capture function, select yes in the...

54

Setting
Enter	a	Logo	PIN	code
Use the Point ▲▼ buttons to enter a number. Press the Point ► 
button to fix the number and move the red frame pointer to the next 
box. The number changes to . If you fixed an incorrect number, 
use the Point ◄ button to move the pointer to the number you 
want to correct, and then enter the correct number.
Repeat this step to complete entering a four-digit number.
After entering the four-digit number, move the pointer to “Set”. 
Press the SELECT button so that you...

55

Setting
Picture	in	PicturePicture	in	PictureSelected Mode
Status (Stored /Free/ Adj .) of the selectedmode.
Position	Menu
Active frame
(White)
Center line
display
Note:
 •	The	Picture	in	Picture	function	is	not	available	depending	on	the	input	signals	and	the	selected	input	terminals.	Refer	to	‘List	of	Picture	in	Picture‘	for	details.	(p.89)	 •	When	the	input	signal(s)	is/are	incompatible,	X	mark	will	be	displayed	on	the	Main/Sub	picture.
This function is used to project two images simultaneously...

56

This function is only used for HDMI input source.
 	Image
Select Normal or Enhanced to match the video range 
setting of your HDMI Digital RGB equipment.
		Sound
        HDMI: When using the HDMI cable, select HDMI.  
                   Both video and audio are transferred and you 
                   need not to connect any additional cables for 
                   audio. 
        AUDIO	1	: When using the DVI-HDMI cable, select   
                         AUDIO	1 and connect the audio cable to...

57

This function allows you to change brightness of the screen.
Lamp	life	control
Lamp	control
Select the lamp operation when the total lighting time of a lamp 
exceeds the recommended total hours of use.
					Mode	1 ............  A lamp can be turned on even after
                               exceeding the recommended total hours of \
use.
					Mode	2 ............  A lamp can be turned on even after 
exceeding the recommended total hours of 
use. But the projector turns off automatically 
after 3...

5

Choose the running speed of cooling fans from the following options.
 Normal ......  Operate in this mode under normal conditions.
 Max ...........  Use this mode when you want to increase the cooling 
effect when operating the projector in high ambient 
temperature environment. Fan noise is louder than 
Normal. 
Setting
Simple	mode	buttons
Only these buttons are active when the simple mode is set to On.  [ON, STAND-BY, INPUT, AUTO PC, INFO., MENU, SCREEN, SHUTTER, ▲▼◄►, SELECT, VOL.+, VOL.-,...

59

Note:
	 •	Factory	default	is	Ready: 5 Min.	 •		
When	the	shutter	is	closed	while	the	Power	management	function	is	working,	the	Power	management	function	is	released.
Setting
Select a location of the infrared remote receiver of the remote control.\
 See “Remote Control Receivers and Operating Range” on page 15 for \
details.
 All ............  Activate all of the receivers.
 Front	&	Top. . . . . .Activate both the front and top receivers.
 Top	&	Back . . . . . .Activate both the top and back...

60

Setting
When this function is set to On, the projector will be automatically 
turned on just by connecting the AC power cord to the wall outlet.
Note:
				 Be	sure	to	turn	off	the	projector	properly	(see	“Turning	Off	the	Projector”	on	page	24).	If	the	projector	is	turned	off	in	the	incorrect	sequence,	the	Direct	on	function	does	not	work	properly.
You can emphasize a part of the projected image with this function. 
Use the Point ▲▼ buttons to select a pattern of the Pointer (Arrow, 
Finger, or...