Eiki Projector Lc Wxl200al User Manual

11

⑦ R/C	jACK When using the wired remote control, connect the wired remote control to this jack with a remote control cable (supplied) (p.15).
⑮ USB	CONNECTOR	(Series	B) Use this connector when controlling a computer with the remote control of the projector. Connect the USB terminal of your computer to this connector with a USB cable (p.19).
⑭ AUDIO	2	jACK Connect the audio output (stereo) signal from a computer or video equipment (p.21).
⑪ VIDEO	INPUT	jACK Connect the component or the composite video...

12

① ON/STAND-By	button
 Turn the projector on or off (pp.23-24).
② MENU	button
 Open or close the On-Screen Menu (p.25).
⑤ Point	▲▼◄►	(	VOLUME	–	/	+	)	buttons
 – Select an item or adjust the value in the On-
Screen Menu (p.25).
  – Pan the image in Digital zoom + mode (p.43).
  – Adjust the volume level (with Point ◄► buttons) 
(p.28).
⑩ WARNING	TEMP  .	indicator
 Blink red when the internal temperature of the 
projector exceeds the operating range (pp.72, 
79-80).
④ SHUTTER	button
   Close and open...

1

① STAND-By	button
 Turn the projector off (p.24).
④	 ON	button
 Turn the projector on (p.23).
⑥ INPUT	button
 Select a signal (pp.33-35).
⑧ SCREEN	button
 Select the screen size (p.29).


⑭

⑭ L-CLICK	button
 Act as the left mouse button for wireless mouse 
operation (p.32).
③ SIGNAL	EMISSION	indicator
 Light red while a signal is being sent from the 
remote control to the projector.
⑨ POINT	▲▼◄►(	VOLUME	–	/	+,	MUTE)	buttons
 – Select an item or adjust the value in the On-
Screen Menu...

14

⑯
⑮
⑲
⑰
⑱
⑱ ZOOM	▲▼ buttons
 Zoom in and out the images (p.29).
⑮ D .ZOOM	button
 Select the Digital zoom +/- mode and resize the 
image (p.43).
⑲ PIP 	button
 Operate the Picture in Picture function. (pp.30,55-56)
㉒		FILTER	button
   Scroll the filter (p.30).
㉔   FREEZE	button
 Freeze the picture on the screen (p.30).⑰ KEySTONE	button
 Correct keystone distortion (pp.31, 44, 50).
⑳	 RESET/ON/ALL-OFF	switch
 When using the remote control, set this switch to 
“ON”.  Set it to “ALL OFF” for power...

15

12
Open the battery 
compartment lid.
Install new batteries into 
the compartment.
Replace the 
compartment lid.
Press the lid downward and slide it.Two	AAA	size	batteriesFor correct polarity (+ and –), be sure battery terminals are in contact with pins in the compartment.
To ensure safe operation, please observe the following precautions :
 ● Use two (2) AAA or LR03 type alkaline batteries.
 ● Always replace batteries in sets.
 ● Do not use a new battery with a used battery.
 ● Avoid contact...

16

The eight different remote control codes (Code 1–Code 8) are assigned to this pr\
ojector. Switching the remote control 
codes prevents interference from other remote controls when several proj\
ectors or video equipment next to each other are 
operated at the same time. Change the remote control code for the projec\
tor first before changing that for the remote control. 
See “Remote control” in the Setting Menu on page 58.
Press and hold the MENU and a number button (1–8) for 
more than five...

17

Installation
For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the screen.
Note:
	 •	The	brightness	in	the	room	has	a	great	influence	on	picture	quality.	It	is	recommended	to	limit	ambient	
				lighting	in	order	to	obtain	the	best	image.
	 •	All	measurements	are	approximate	and	may	vary	from	the	actual	sizes.
Positioning	the	Projector
60%
10%
Lens shift center positionShift range
Lens	Shift	Adjustment
Projection lens can be moved from side...

1

When replacing the lens or using an optional lens, install the lens by f\
ollowing the instructions below. Ask the 
sales dealer for detailed information of the optional lens specification\
s. 
Shift the lens to the center position by using the Lens 
shift function (p.27).1
2
Removing	the	lens
CAUTION
Be careful when handling the lens. Do not drop.

Installation
While pressing the Lens release button on the top
of the cabinet, turn the lens counterclockwise until
it stops and pull it out...

19

Monitor Output
BNCcable
DVI Output
G   B   R   H/V   V
HDMI-DVI cableVGA cableVGA cableUSB cable
USB port
Unplug	the	power	cords	of	both	the	projector	and	external	equipment	from	the	AC	outlet	before	connecting	cables.
Cables	used	for	connection  ( = Cables not supplied with this projector.)
• VGA Cable (One cable is supplied.) 
• HDMI-DVI cable  
• BNC cable  
• Serial Cross cable 
• USB cable 
Monitor Output
HDMIANALOG INANALOG OUTUSB
Serial Crosscable
Serial out
CONTROL PORT
Installation
See...

20

RGB Scart21-pin Output
S-video cable
S-video OutputComposite Video
Y - Pb/Cb - Pr/Cr
BNC cable
Unplug	the	power	cords	of	both	the	projector	and	external	equipment	from	the	AC	outlet	before	connecting	cables.
Cables	used	for	connection ( = Cables not supplied with this projector.)
• Video cable (RCA x 1 or RCA x 3) • BNC cable (BNC x 1 or BNC x 3) • S-video cable • Scart-VGA cable   • HDMI cable 
Component Video OutputComposite Video
Component Video  Output(Y, Pb/Cb, Cr/Pr)HDMI Output
RCA...