Eiki Projector Lc Wxl200al User Manual

							
11

⑦ R/C	jACK When using the wired remote control, connect the wired remote control to this jack with a remote control cable (supplied) (p.15).
⑮ USB	CONNECTOR	(Series	B) Use this connector when controlling a computer with the remote control of the projector. Connect the USB terminal of your computer to this connector with a USB cable (p.19).
⑭ AUDIO	2	jACK Connect the audio output (stereo) signal from a computer or video equipment (p.21).
⑪ VIDEO	INPUT	jACK Connect the component or the composite video output signal from video equipment to these jacks (p.20).
③ CONTROL 	PORT	CONNECTOR When controlling the projector with RS-232C, connect the control equipment to this connector with the serial control cable. (p.19)
⑧ HDMI	TERMINAL Connect the HDMI signal (including sound signal) from video equipment or the DVI signal from computer to this terminal (pp.19, 20).
       is registered trademarks of HDMI    
                    Licensing, LLC.
⑤ COMPUTER	INPUT	TERMINAL	(ANALOG) Connect the computer (or RGB scart) output signal to this terminal (pp.19-20).
⑨ 5	BNC	INPUT	jACKS Connect the component or composite video output signal from video equipment to VIDEO/Y, Pb/Cb, and Pr/Cr jacks or connect the computer output signal (5 BNC Type [Green, Blue, Red, Horiz. Sync, and Vert. Sync.]) to G, B, R, H/V, and V jacks (pp.19-20).
③
Part	Names	and	Functions
⑩ S-VIDEO	INPUT	jACK Connect the S-VIDEO output signal from video equipment to this jack (p.20).
⑬ AUDIO	1	jACK Connect the audio output (stereo) signal from a computer or video equipment (p.21).
④⑤⑧
⑪⑬
 Kensington	Security	Slot
 This slot is for a Kensington lock used to deter 
    theft of the projector.
 *Kensington is a registered trademark of ACCO Brands Corporation.
① INFRARED	REMOTE	RECEIVER	(Back)  The infrared remote receiver is also located in the front and top (pp.10, 15).
④ ANALOG	OUT	TERMINAL This terminal can be used to output the incoming analog RGB signal from INPUT 1-3 terminal to the other monitor (pp.19-20).
⑥⑦
⑭⑫⑨
②
⑮
② LAN	CONNECTION	TERMINAL Connect the LAN cable (refer to the owner’s manual of “Network Set-up and Operation”).
①
⑩
⑫ AUDIO		jACKS	(L(MONO)/R) Connect the audio output signal from video equipment connected to ⑩ or ⑪ to this jack. For a monaural audio signal (a single audio jack), connect it to the L (MONO) jack (p.21).
Rear	Terminal
⑥ AUDIO	OUTPUT	j ACK	(VARIABLE) This jack outputs the audio signal from computer or video or HDMI equipment to external audio equipment (p.21). 
						

							
12

① ON/STAND-By	button
 Turn the projector on or off (pp.23-24).
② MENU	button
 Open or close the On-Screen Menu (p.25).
⑤ Point	▲▼◄►	(	VOLUME	–	/	+	)	buttons
 – Select an item or adjust the value in the On-
Screen Menu (p.25).
  – Pan the image in Digital zoom + mode (p.43).
  – Adjust the volume level (with Point ◄► buttons) 
(p.28).
⑩ WARNING	TEMP  .	indicator
 Blink red when the internal temperature of the 
projector exceeds the operating range (pp.72, 
79-80).
④ SHUTTER	button
   Close and open up the built-in shutter. (p.27)
 ⑧ POWER	indicator
– Light green while the projector is in stand-by mode.
– Light green during operations.
– Blink green in the Power management mode (p.59).
③ SELECT	button
  – Execute the selected item (p.25).
  – Expand or compress the image in the Digital 
zoom mode (p.43).
⑨ LAMP 	indicator
 Light red during operations.
⑬ LAMP 	REPLACE	indicator
 Light orange when the projection lamp reaches 
its end of life (pp.69, 80).
⑪ WARNING	FILTER	indicator
 – Blink slow when the filter is being scrolled 
(pp.66, 79). 
  – Blink fast when the filter scroll is not working 
properly or the filter cartridge is not installed 
(pp.66, 81).
  – Light orange when the clogging of the filter is 
detected or the filter counter reaches a time 
set in the timer setting, urging immediate 
filter/ filter cartridge replacement (pp.65, 66, 
81).
①
Side	ControlIndicators	(on	the	top	panel)
Part	Names	and	Functions
⑦ INPUT	button
  Select an input source (pp.33-35).
⑥ LENS	button
 Enter the focus, zoom, and lens shift adjustment 
mode (p.27).
②
④⑥
③
⑤
⑦⑨
⑧
⑩
⑪
⑫
⑬
⑫ SHUTTER	indicator
 Light blue when the shutter is closed (p.79).
Side	Control	and	Indicators 
						

							
1

① STAND-By	button
 Turn the projector off (p.24).
④	 ON	button
 Turn the projector on (p.23).
⑥ INPUT	button
 Select a signal (pp.33-35).
⑧ SCREEN	button
 Select the screen size (p.29).


⑭

⑭ L-CLICK	button
 Act as the left mouse button for wireless mouse 
operation (p.32).
③ SIGNAL	EMISSION	indicator
 Light red while a signal is being sent from the 
remote control to the projector.
⑨ POINT	▲▼◄►(	VOLUME	–	/	+,	MUTE)	buttons
 – Select an item or adjust the value in the On-
Screen Menu (p.25).
  – Pan the image in Digital zoom + mode (p.43).
  – Adjust the volume level (with Point ◄► buttons) 
or mute the sound (with Point ▼ button.) (p.28).
To ensure safe operation, observe the following 
precautions:
– Do not bend, drop, or expose the remote control to   
   moisture or heat.
–  For cleaning, use a soft dry cloth. Do not apply 
benzene, thinner, spray, or any other chemical 
materials.

② WIRED	REMOTE	jack
  Connect the remote control cable (supplied) to this 
jack when using as a wired remote control.⑪	SELECT	button
 – Execute the selected item (p.25).
  – Expand or compress the image in the Digital 
zoom mode (p.43).

⑦	 MENU	button
  Open or close the On-Screen Menu (p.25).
⑫
⑩	 MOUSE	POINTER	button
 Move a pointer of the projector or a pointer for 
wireless mouse operation (p.32).
Part	Names	and	Functions
⑤ AUTO	PC	button
 Automatically adjust the computer image to its 
optimum setting (pp.29, 37).
⑬


⑪
⑬ INFO .	button
 Display the input source information (p.29).
⑫ SHUTTER	button
	Close and open up the built-in shutter (pp.27, 29). 
Remote	Control 
						

							
14

⑯
⑮
⑲
⑰
⑱
⑱ ZOOM	▲▼ buttons
 Zoom in and out the images (p.29).
⑮ D .ZOOM	button
 Select the Digital zoom +/- mode and resize the 
image (p.43).
⑲ PIP 	button
 Operate the Picture in Picture function. (pp.30,55-56)
㉒		FILTER	button
   Scroll the filter (p.30).
㉔   FREEZE	button
 Freeze the picture on the screen (p.30).⑰ KEySTONE	button
 Correct keystone distortion (pp.31, 44, 50).
⑳	 RESET/ON/ALL-OFF	switch
 When using the remote control, set this switch to 
“ON”.  Set it to “ALL OFF” for power saving when 
it is not in use. Slide this switch to “RESET” to 
initialize the remote control code. (p.16)
㉖  R-CLICK	button
 Act as the right mouse button for wireless mouse 
operation (p.32).
㉓  LENS	SHIFT	button
 Select the Lens Shift function (p.29).
㉕   P-TIMER	button
 Operate the P-timer function (pp.30, 60).
㉗
㉘  NUMBER	buttons
 Act as number buttons. Use these buttons when 
setting the remote control codes (p.16) or when 
entering the PIN code numbers (pp. 23, 54, 62).
㉓
㉒
⑳
㉔
㉕
㉗  POINTER	button
 Act as the On-Off switch for the Pointer (pp.30, 32, 
60).
㉘
For PIN code and remote control code.
Part	Names	and	Functions
㉖
⑯ INPUT	1-		buttons
 Select an input source (INPUT 1 – INPUT 3) 
 (pp.33-35).
Remote	Control
㉑
㉑ FOCUS	buttons
 Adjust the focus (p.29). 
						

							
15

12
Open the battery 
compartment lid.
Install new batteries into 
the compartment.
Replace the 
compartment lid.
Press the lid downward and slide it.Two	AAA	size	batteriesFor correct polarity (+ and –), be sure battery terminals are in contact with pins in the compartment.
To ensure safe operation, please observe the following precautions :
 ● Use two (2) AAA or LR03 type alkaline batteries.
 ● Always replace batteries in sets.
 ● Do not use a new battery with a used battery.
 ● Avoid contact with water or liquid.
 ● Do not expose the remote control to moisture or heat.
 ● Do not drop the remote control.
 ● If the battery has leaked on the remote control, carefully wipe the case clean and install new 
batteries.
 ● Risk of an explosion if battery is replaced by an incorrect type. 
 ● Dispose of used batteries according to the instructions or your local disposal rule or guidelines.
Point the remote control toward the projector (to Infrared Remote 
Receivers) when pressing the buttons. Maximum operating range 
for the remote control is about 16.4’ (5 m) and 60 degrees in front, 
back and top of the projector.
Infrared Remote Receivers are provided in front, back and top of of 
the projector. You can conveniently use all of the receivers (pp. 10, 
11, 59).
The remote control can be used as a wired remote control. Wired 
remote control helps you use the remote control outside of the 
operating range (16.4’/ 5 m). Connect the remote control and the 
projector with the remote control cable (supplied). Connected with 
the remote control cable, the remote control does not emit wireless 
signal.
Part	Names	and	Functions
Note:
    When	hanging	the	projector	from	the	ceiling,	select	the	Infrared	Remote	Receiver	which	is	located	farther	away	from	the	fluorescent	light	(p.59).
Remote	Control	Battery	Installation
Wired	Remote	Control	Transmitter
Remote	Control	Receivers	and	Operating	Range
16.4’(5 m)
16.4’(5 m) 
						

							
16

The eight different remote control codes (Code 1–Code 8) are assigned to this pr\
ojector. Switching the remote control 
codes prevents interference from other remote controls when several proj\
ectors or video equipment next to each other are 
operated at the same time. Change the remote control code for the projec\
tor first before changing that for the remote control. 
See “Remote control” in the Setting Menu on page 58.
Press and hold the MENU and a number button (1–8) for 
more than five seconds to switch between the codes.1
To initialize the remote control code, slide the RESET/ ON/
ALL-OFF switch to “RESET”, and then to “ON”.  The initial 
code is set to Code	1.
2
MENU	button
Number	buttons(1-)
RESET/ON/ALL	OFF	Switch
Press and hold the MENU and a number button 
(1-8) that corresponds to the remote control code 
for more than five seconds to switch between the 
codes. 
Part	Names	and	Functions
Remote	Control	Code
Projection angle can be adjusted up to 4.0 degrees with the 
adjustable feet. 
Rotate the adjustable feet and tilt the projector to the proper height; \
to raise the projector, rotate the both feet clockwise.
To lower the projector or to retract the adjustable feet, rotate the 
both feet counterclockwise.
To correct keystone distortion, press the KEYSTONE button on the 
remote control or select Keystone from the menu (see pages 14, 
31, 44, 50).
Adjustable	Feet
Adjustable Feet 
						

							
17

Installation
For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the screen.
Note:
	 •	The	brightness	in	the	room	has	a	great	influence	on	picture	quality.	It	is	recommended	to	limit	ambient	
				lighting	in	order	to	obtain	the	best	image.
	 •	All	measurements	are	approximate	and	may	vary	from	the	actual	sizes.
Positioning	the	Projector
60%
10%
Lens shift center positionShift range
Lens	Shift	Adjustment
Projection lens can be moved from side to side and up and down with the \
motor-driven lens shift function. This function 
makes the positioning of images easy on the screen. (See page 27)
The display position can be shifted upward up to 60% elevation of the display.
The display position can be shifted downward up to 60% low level of the display.
The display position can be shifted to the left in up to 10% width of the display.The display position can be shifted to the right in up to 10% width of the display.
When the lens is shifted to top.When the lens is shifted to bottom.
When the lens is shifted to leftmost.When the lens is shifted to rightmost.
Lens	shift	adjustable	range
100”
47.2’(14.4 m)
35.4’(10.8 m)
23.6’ (7.2 m)
11.8’ (3.6 m)
200”
300”
400”
250”
188”
125”
63”40”
Max. Zoom
Min. Zoom
Screen Size(W x H) mm16:10 aspect ratio
Zoom (min.)
40”
Zoom (max.)
862 x 538
4.5(1.4 m)
7.9(2.4 m)
100”
2154 x 1346
11.8’ (3.6 m)
19.7 (6.0 m)
200”
4308 x 2692
23.6’ (7.2 m)
40.0 (12.2 m)
300”
6462 x 4039 
35.4’(10.8 m)
60.0 (18.3 m)
400”
8616 x 5385 
47.2’(14.4 m)
80.1 (24.4 m)
(Inch Diagonal)
(Center)
80.1 (24.4 m)
400”
4.5(1.4 m) 
						

							
1

When replacing the lens or using an optional lens, install the lens by f\
ollowing the instructions below. Ask the 
sales dealer for detailed information of the optional lens specification\
s. 
Shift the lens to the center position by using the Lens 
shift function (p.27).1
2
Removing	the	lens
CAUTION
Be careful when handling the lens. Do not drop.

Installation
While pressing the Lens release button on the top
of the cabinet, turn the lens counterclockwise until
it stops and pull it out slowly from the projector.
Turn off the projector and unplug the AC power cord. 
NOTES	ON	LENS	INSTALLATION
 ● Do not touch or remove any parts except the lens and related parts. It may result in    
 malfunctions, electrical shock, fire hazard or other accidents.
 ● Before installing or replacing the lens, check that the Model No. of the Projection Lens  
 matches to the projector.
 ● For details of the lens and installation, contact the sales dealer where you purchased the 
 projector.
Fit the lens to the projector by aligning the red dot on 
the lens with the red dot of the projector.
1
Slowly turn the lens clockwise until it clicks. Make sure 
that the lens is fully inserted to the projector.
2
Remove the lens mount cover.
CAUTION
Do not press the lens release button when attaching 
the lens.
Lens	Installation
Attaching	the	lens	to	the	projector
Lens release button
Red dots 
						

							
19

Monitor Output
BNCcable
DVI Output
G   B   R   H/V   V
HDMI-DVI cableVGA cableVGA cableUSB cable
USB port
Unplug	the	power	cords	of	both	the	projector	and	external	equipment	from	the	AC	outlet	before	connecting	cables.
Cables	used	for	connection  ( = Cables not supplied with this projector.)
• VGA Cable (One cable is supplied.) 
• HDMI-DVI cable  
• BNC cable  
• Serial Cross cable 
• USB cable 
Monitor Output
HDMIANALOG INANALOG OUTUSB
Serial Crosscable
Serial out
CONTROL PORT
Installation
See the next page for the signals that can output to the ANALOG OUT terminal.
•Monitor Input
•
Connecting	to	a	Computer	(Digital	and	 Analog	RGB) 
						

							
20

RGB Scart21-pin Output
S-video cable
S-video OutputComposite Video
Y - Pb/Cb - Pr/Cr
BNC cable
Unplug	the	power	cords	of	both	the	projector	and	external	equipment	from	the	AC	outlet	before	connecting	cables.
Cables	used	for	connection ( = Cables not supplied with this projector.)
• Video cable (RCA x 1 or RCA x 3) • BNC cable (BNC x 1 or BNC x 3) • S-video cable • Scart-VGA cable   • HDMI cable 
Component Video OutputComposite Video
Component Video  Output(Y, Pb/Cb, Cr/Pr)HDMI Output
RCA cableHDMI cable
Scart-VGA cable
VideoHDMIANALOG INANALOG OUTS-VIDEO
Installation
Input	TerminalMonitor	OutCable
Input 1D-sub15RGB (PC analog)YESRGB (SCART)NOHDMIHDMINO
Input 25 BNCRGBYESVideoYESY, Pb/Cb, Pr/CrYES
Input 3RCAY, Pb/Cb, Pr/CrYESS-videoS-videoNOVideoVideoYESNetworkNO
Analog	Out	Signal	Table
Refer to the Analog Out Signal Table (above).
A cable with one end D-sub 15 and the other end (Black box) compatible with each equipment is necessary. 
VideoY - Pb/Cb - Pr/Cr
Connecting	to	Video	Equipment	(Video,	S-video,	HDMI)