Eiki Projector Lc Wxl200al User Manual

							
71

Unplug the AC power cord before cleaning.
Gently wipe the projection lens with a cleaning cloth that 
contains a small amount of non-abrasive camera lens cleaner, 
or use a lens cleaning paper or commercially available air 
blower to clean the lens. 
Avoid using an excessive amount of cleaner. Abrasive 
cleaners, solvents, or other harsh chemicals might scratch the 
surface of the lens.
Unplug the AC power cord before cleaning.
Gently wipe the projector body with a soft dry cleaning cloth. 
When the cabinet is heavily soiled, use a small amount of 
mild detergent and finish with a soft dry cleaning cloth. Avoid 
using an excessive amount of cleaner. Abrasive cleaners, 
solvents, or other harsh chemicals might scratch the surface 
of the cabinet.
When the projector is not in use, put the projector in an 
appropriate carrying case to protect from dust and scratches.
Maintenance	and	Care
Cleaning	the	Projection	Lens
Cleaning	the	Projector	Cabinet
Do not use any flammable solvents or air sprays on the projector and in \
its vicinity. The explosion or fire hazard 
may occur even after the AC power cord is unplugged because the temperature inside the projector \
is extremely 
high due to the lamps. In addition, there is a risk that the internal pa\
rts may be damaged not only by the 
flammable air spray but also by the cold air.
CAUTION 
						

							
72

The WARNING indicators show the state of the function which protects the proj\
ector. Check the state of the WARNING 
indicators and the POWER indicator to take proper maintenance. 
The	projector	is	shut	down	and	the	WARNING	
TEMP .	indicator	is	blinking	red .
When the temperature inside the projector reaches a
certain level, the projector will be automatically shut down to 
protect the inside of the projector. The POWER indicator is blinking 
while the projector is being cooled down. When the projector has 
cooled down enough (to its normal operating temperature), it can 
be turned on again by pressing the ON/STAND-BY button.
Note:
  	 The	WARNING	TEMP.	indicator	continues	to	blink	even	after	the	temperature	inside	the	projector	returns	to	normal.	When	the	projector	is	turned	on	again,	the	WARNING	TEMP.	indicator	stops	blinking.	
Then	check	the	matters	below:
–  Did you provide appropriate space for the projector to be 
ventilated? Check the installing condition to see if the air vents of 
the projector are not blocked.
–  Has the projector been installed near an Air-Conditioning/ 
Heating Duct or Vent? Move the installation of the projector away 
from the duct or vent.
–  Is the filter clean? Replace the filter with a new one.
The	projector	is	shut	down	and	the	LAMP 	indicator	is	
lighting	and	other	indicators	are	blinking .
When the projector detects an abnormal condition, it will
be automatically shut down to protect the inside of the
projector and the LAMP indicator lights on and other indicators 
blink. In this case, unplug the AC power cord and plug it, and then
turn on the projector once again to verify operation. If the
projector cannot be turned on and these indicators are still lighting 
and blinking, unplug the AC power cord and contact
the service center.
CAUTION
DO NOT LEAVE THE PROJECTOR WITH THE 
AC POWER CORD CONNECTED UNDER AN 
ABNORMAL CONDITION. IT MAY RESULT IN 
FIRE OR ELECTRIC SHOCK.
Top	Panel
LAMP	indicator	lights	on	and	other	indicators	blink .
Top	Panel
WARNING	TEMP  .blinking	red
Maintenance	and	Care
Warning	Indicators 
						

							
7

Before calling your dealer or service center for assistance, check the i\
tems below once again.
1. Make sure you have properly connected the projector to peripheral equipment as described on pages 19-21.
2. Check the cable connection. Make sure that all computers, video equipment, and power cords are properly connected.
3. Make sure that all power is switched on.
4. If the projector still does not produce an image, restart your computer.
5. If an image still does not appear, disconnect the projector from your computer and check your computer monitor’s display. 
A problem may be noticed with your graphics controller rather than with t\
he projector. (When you reconnect the projector, 
be sure to turn the computer and monitor off before you turn on the projector. Turn on equipment in the order of the 
projector and computer.)
6. If a problem still persists, check the following solutions.
Appendix
Problem:Solutions
No	power  .
– Plug the power cord of the projector into the AC outlet.
–  Wait until the POWER indicator stops blinking to turn on the projector ag\
ain. (See 
page 23)–  Check the WARNING TEMP. indicator. If the WARNING TEMP. indicator is blinking, 
the projector cannot be turned on. (See page 72)– Unlock the Key lock function for the projector.  (See page 61)–  See if the filter cartridge is inserted.  (See page 67)– Check the projection lamp.  (See page 70)
PIN	code	dialog	box	
appears	at	start-up .
– PIN code lock is being set. Enter a PIN code; the “1234” or numbers 
PIN code lock is being set. Enter a PIN code; the “1234” or number\
s	you have set. 
(See pages 23, 61-62)
The	initial	display	is	not	
shown .
– Make sure Off or Countdown	Off is not chosen at Display function.
   (See “Setting” section on page 52)
The	initial	display	is	not	
same	with	the	default	one .
– Make sure User or Off is not chosen at Logo select function.
   (See “Setting” section on page 52)
When	the	projector	is	on	
and	you	press	the	input	
button,	an	icon	other	
than	the	Lamp	mode	icon	
appears .
– That is the Filter warning icon. (See page 66)That is the Filter warning icon. (See page 66)
An	icon	other	than	Input	
mode	or	Lamp	mode	icon	
appears .
– That is the Lamp replacement icon or the Filter warning icon. (See pages 66,69)That is the Lamp replacement icon or the Filter warning icon.  (See pag\
es 66,69)
No	image .
– Check the connection between your computer or video equipment and t\
he projector.
–   See if the input signal is correctly output from your computer. Some laptop computers 
may need to be changed the setting for monitor output when connected to \
the 
projector. See your computer’s instruction manual for the setting.
– It takes about 30 seconds to display an image after turning on the \
projector.
– See if the selected system is corresponding with your computer or v\
ideo equipment.
– Select correct input source once again through menu operation.  (S\
ee pages 33-35)
–  Make sure the temperature is not out of Operating Temperature (41˚F–104˚F [5˚C–
40˚C]).
 
appears	on	the	screen
–  End of lamp life is approaching. Replace the lamp with a new one promptl\
y.  (See 
page 69)
Troubleshooting 
						

							
74

appears	on	the	screen
–  Filter is out of scroll. Replace the filter cartridge with a new one promptly.  (See pages 
67-68)
The	image	is	out	of	focus .
– Adjust the focus of the projector.
– Check Projection Lens to see if it needs cleaning.
 Note:  Moving	the	projector	from	a	cool	temperature	location	to	a	warm	temperature	
location	may	result	in	moisture	condensation	on	Projection	Lens.	In	such	
cases,	leave	the	projector	OFF 	and	wait	until	condensation	evaporates.
–   Projecting  from  excessive  slant  angle  to  the  screen  may  cause  keystone  distortion 
and partial imperfect focus.
– Make sure the projection screen is at least 4.3’ (1.3 m) away from the projector.
The	image	is	not	bright	
enough .
– Check if Contrast or Brightness is adjusted properly. (See pages 41, 47) 
– Check if Image	level is selected properly. (See pages 40, 46)
– Check the Lamp control function. ( See “Setting” section on \
page 57)
–  Check  the  LAMP  REPLACE  indicator.  If  it  lights,  the  end  of  lamp  life  is  approaching. 
Replace the lamp with a new one promptly.  (See page 69)
The	color	is	strange .– Check the Input signal, color system, video system, or computer sys\
tem mode.
– Adjust the Image Level properly.  (See pages 40, 46)
The	image	is	Left/Right	
reversed .– Check the Ceiling / Rear function.  (See pages 44, 50)
The	image	is	Top/Bottom	
reversed .– Check the Ceiling function.  (See pages 44, 50)
The	image	is	distorted	or	
runs	off .– Check PC adjust Menu or Screen Menu and adjust them.
Auto	PC	adjustment	
function	does	not	work.
–  Check the Input signal.  Auto PC Adjustment function cannot work when 40p, 575p, 
720p, 40i, 575i, 105i, 100i	or 100p is selected or or when the digital signal is or or when the digital signal isor or when the digital signal is 
input into HDMI terminal. See page 37. 
Some	displays	are	not	
seen	during	the	operation .– Check the Display function.  (see page 52)
The	setting	does	not	
remain	after	turning	off	
power  .
–  Make  sure  you  selected Store  after  adjusting  settings.  Some  settings  cannot  be 
stored if not registered with Store function.
Power	management	
function	does	not	work .
–  Power  management  function  cannot  work  while  Freeze  function  is  running  or  the 
shutter is closed.
Image	disappears	
automatically  .
–  Check the power management function in the Setting. The power management is setCheck the power management function in the Setting. The power management is set 
to On at the factory.
Capture	function	does	not	
work .
– Check the connection to see if there is signal.
–Capture function is not available when the Picture in Picture function is set toCapture function is not available when the Picture in Picture function i\
s set to User1-5.
Some	menus	cannot	be	
selected .– Each of the Video Input and Computer Input has a limit on selectable menus.
No	sound
– Check the audio cable connection from audio input source.
– Adjust the audio source.
– Press the Volume + button.  ( See page 28)
– Press the Mute button.  (See page 28)
– Is the image projected? You will hear the sound only when the image is projected.Is the image projected? You will hear the sound only when the image is projected.
– Check the Build-in SP function. (See page 28)(See page 28)
Appendix 
						

							
75

WARNING:	
High	voltages	are	used	to	operate	this	projector .	Do	not	attempt	to	open	the	cabinet .
If  problems  still  persist  after  following  all  operating  instructions,  contact  the  dealer  where  you  purchased  the  projector  or  the 
service center. Specify the model number and explain about the problem. We will advise you how to obtain service.
Appendix
The	power	is	turned	off	
automatically .
–  Power  management  function  runs  by  initial  setting.  Check  “Setting”  section  on  page  
59.
–  When the filter cartridge replacement icon keeps appearing on the screen\
 at turning 
on the projector for some time and no action is taken to replace the fil\
ter cartridge, the 
projector will be automatically shut down in 3 minutes after turning on \
to protect the 
projector. (See pages 66, 81)
–  Do not cover the ventilation slots on the projector. (See pages 4, 6)
–  Projector may be used in high ambient temperature environment. Make sure\
 the 
temperature is not out of Operating Temperature (41˚F–104˚F [5˚C–40˚C]). (See page 
72)
you	cannot	operate	with	
the	side	control .
–   If the side control is locked at "Key lock" under "Security" of Setting \
menu, the side
  control is not available. Please check “Setting” section on page\
 61.
The	Remote	Control	does	
not	work .
– Check the batteries.
– Check if the RC sensor is set properly.  (See page 59)
– Make sure no obstruction is between the projector and remote contro\
l.
–  Make sure you are not too far from the projector when using the remote c\
ontrol.
Maximum operating range is 16.4’ (5m). (See page 15)
–  Make  sure  that  the  remote  control  code  conforms  to  the  projector ’s  code.  (See 
“SETTING” section on page 58.)
– Unlock the Key lock function for the remote control.  (See page 61\
)
–  Wireless remote control does not work when the remote control cable is c\
onnected to 
the  projector.  (See page 15)
– Check if the ALL-OFF switch on the remote control is set to “ON.”
–  Make sure that the simple mode in the remote control function is set to \
Off (See page 
58).
Wireless	mouse	function	
does	not	work .
– Check the cable connection between the projector and your computer. (See pages 19, 
   32)
– Check the mouse setting on your computer.
– Turn on the projector before you turn on the computer.
Indicators	blink	or	light .–  Check the status of the projector with referring to “Indicators and p\
rojector condition” on 
pages 79-81.
appears	on	the	screen
– Your operation is invalid. Operate correctly.
Unable	to	unlock	the	Logo	
PIN	code	lock,	Security	
key	lock	or	Security	PIN	
code	lock .
– Contact the dealer where you purchased the projector or the service\
 center.
Forget	the	Logo	PIN	code	
or	Security	PIN	code .	– Contact the dealer where you purchased the projector or the service\
 center. 
						

							
76

InputRGB (PC analog)
Y, Pb/Cb,Pr/Cr
RGB (Scart)
HDMI
Network
Video
RGB
Video
Y, Pb/Cb,Pr/Cr
S-video
Input 3
InputH-sync freq.V-sync freq.
Information
ScreenLanguageLamp status
Power management
Remote control
Note:
		The	Menu	display	varies	depending	on	the	input	signal.
Appendix
Volume
MuteOn/Off
Sound0-63
Built-in SP
PIN code lock
Key lock
SERIAL NO.
Network will be displayed only when an optional Network unit is attached.
*
*
Input 1
Input 2
Lamp counterFilter counter
Simple mode
On/Off
System	(1)Mode 1
Mode 10
 System displayed in the System Menu varies depending on the input signa\
l.
SVGA 1
SVGA 2
SVGA 3
Image	adjustContrastBrightnessColor temp.
Red
Gamma
Store
0–630–63
0–63
0–15
Image 1
Image 10
ResetYes/No
Sharpness0–31
GreenBlue0–630–63
Mid
LowXLow
AdjHigh
OffsetRed/Green/Blue
Image	selectDynamic
Real
Image 1
Image 10
PC	adjustAuto PC adj.
Fine sync.
Total dots
Position H
Position V
Current mode
Clamp
Display area - H
Display area - V
Reset
Mode free
Store
0–31
Yes/No
Mode 1
Mode 10
Quit
Menu	Tree
Computer	Input/HDMI	Input/Video	Input
Computer	Input
Image	adjust
Image	select
PC	adjust
Sound
Information
Input
Shutter management 
Standard 
						

							
77

Note:
	The	Menu	display	varies	depending	on	the	input	signal.
System	(2)Auto
PAL
SECAM
NTSC
NTSC 4.43
PAL-M
PAL-N
System	(3)Auto
1080i
1035i
720p
575p
480p
575i
480i
Image	select
Cinema
Appendix
ScreenNormal
Wide(16:9)Full
Zoom
Rear
Keystone
CeilingResetStore
On/OffOn/Off
Custom adj.H & VScale
Position
H / VOn/OffH / VCommonReset
Reset
Screen
Digital zoom +
Digital zoom -
Video	InputImage	select
Screen
Image	adjustContrastBrightness
Color temp.
Red
Gamma
Store
0–630–63
0–63
0–15
Image 1
Image 10
ResetYes/No
Sharpness0–31
GreenBlue0–630–63
Mid
LowXLow
AdjHigh
OffsetRed/Green/Blue
Image	adjust
Color0–63Tint0–63
Noise reductionOff/On
ProgressiveOff/On/Film
Custom
DynamicStandard
Image 1
Image 10
ScreenNormal
Full
Wide(16:9)
Natural wide
Rear
Keystone
Ceiling
Corner correction
Standard
On/OffOn/Off
Custom adj.H & VScale
Position
H / VOn/OffH / VCommonReset
Reset
Custom
Screen aspect
Zoom
Screen aspect
True
HDMI	Input/Video	Input
1080p
Default(16:10)/16:9/4:3
Corner pattern
Store
Natural
Default(16:10)/16:9/4:3 
						

							
7

SettingLanguage
Fan control
Blue/User/Black
Yes/No
12 languages provided.
Menu position
Lamp control
Filter control
All/Front&Top/Top&Back/Front&Back/Front/Top/Back
Normal/Max
Power management
Background
RC sensor
Ready
Off
Shut down
1–30 Min
On/OffDirect onPointer
On/Countdown Off/OffDisplay
Remote Control
Finger/Arrow/Dot
Appendix
Yes/NoFactory default
ShutterProtection
Management
Remote controlOn/Off
ProjectorOn/Off
5 - 480 Min.
Code 1~Code 8
On/Off
Computer	Input/HDMI	Input/Video	Input
Logo select
Off
User
CaptureYes/NoOff/On
Logo PIN code changeLogo PIN code lock
Default
Logo
Input buttonMode 1/Mode 2/Mode 3
Lamp life control
Lamp controlAuto/Normal/Eco 1/Eco 2
Mode 1/Mode 2
Simple mode
Eco/NetworkStandby mode
P-timerCount up
TimerStart/Stop/Restart
Count down
SecurityOffProjectorRemote control
Key lock
Off/On 1/On 2PIN code changePIN code lock
HFilter counter
Yes/NoOff/400H/700H/1000HFilter counterTimerFilter counter reset
Yes/NoScroll(s)Scrolls remainingScroll counter Reset
8 test patterns providedTest pattern
Setting
ResetExit
Sound
ImageHDMI setup
Closed caption Closed caption
Color
Off/Low/Mid/HighVideo delay control
Picture in Picture 
						

							
79

Check the indicators for the projector condition.  
Indicators
Projector	ConditionPOWER
green
LAMP
red
WARNINGTEMP.
red
WARNINGFILTER
orange
SHUTTER
blue
LAMPREPLACE
orange
The projector is off. (The AC power cord is unplugged.)
The projector is in stand-by mode. Press the ON/
STAND-BY button to turn on the projector.
The projector is operating normally.
(The shutter is open)
The projector is operating normally.
(The shutter is closed)
The projector is preparing for stand-by or the projection 
lamp is being cooled down. The projector cannot be 
turned on until cooling is completed and the POWER 
indicator lights green.
The projection lamp is being cooled down in the Power 
management mode.
The projector is in the Power management mode.
The projection lamp is being cooled down in the Shutter 
management mode.
The projector is in the Shutter management mode.  
Press the ON/STAND-BY button to turn on the 
projector.
The filter is scrolled using the FILTER button on the 
remote control or the Filter control function in the 
setting menu. When the filter is being scrolled, the Filter 
replacement icon and Please	wait . . . message (Fig. 1) 
appear on the screen for about 30 seconds.
The	projector	is	operating	normally .
• • • on
• • • off
• • •  blinking at the normal rate       
(approx. 1 second ON,         
1 second OFF)
• • • dim• • •  blinking slow           
(approx. 2 seconds ON, 2 
seconds OFF)




Appendix
Fig .1   Filter replacement icon and Please	wait . . ..
• • • on (blue)❊❊• • •   blinking at the normal rate (blue 
and dim red) (approx. 1 second 
ON, 1 second OFF)
❊• • • blinking fast (blue and dim red) 
(approx. 0.5 seconds ON,  0.5 
seconds OFF)
• • • blinking fast              
(approx. 0.5 seconds ON,  0.5 
seconds OFF)• • • on (red)❖
❖• • • dim (red)
❖
❖

❖
❖
❖











• • • Differ according to conditions.






Indicators	and	Projector	Condition
❊
❊
❊
❖
❖
❖ 
						

							
0

The	projector	is	detecting	abnormal	condition .
Indicators
Projector	ConditionPOWER
green
LAMP
red
WARNINGTEMP.
red
WARNINGFILTER
orange
SHUTTER
blue
LAMPREPLACE
orange
The temperature inside the projector is elevated close to the 
abnormally high level.
The temperature inside the projector is abnormally high. The 
projector cannot be turned on. When the projector is cooled 
down enough and the temperature returns to normal, the 
POWER indicator lights green and the projector can be turned 
on. (The WARNING TEMP. indicator keeps blinking.) Check and 
replace the filter.
The projector has been cooled down enough and the 
temperature returns to normal. When turning on the projector, the 
WARNING TEMP. indicator stops blinking. Check and replace 
the filter.
The lamp cannot light up. (The projector is preparing for stand-
by or the projection lamp is being cooled down. The projector 
cannot be turned on until cooling is completed.)
The lamp cannot light up. (The lamp has been cooled down 
enough and the projector is in stand-by mode and ready to be 
turned on with the ON/STAND-BY button.)
The lamp has been used overtime. Replace the lamp 
immediately.
 When the filter detects clogging, reaches a time set in the timer settin\
g or runs out of the filter scroll, the WARNING 
FILTER indicator lights orange. When this indicator lights orange, replace \
the filter or the filter cartridge with a new one 
promptly. Reset the Filter counter and Scroll counter after replacing the filter\
 cartridge (p.68). 




Appendix
 When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights orange. When this indicator lights 
orange, replace the projection lamp with a new one promptly. (p.69)
WARNING	FILTER
LAMP 	REPLACE	





❖
❖
❖
❖
❖






