Eiki Projector Lc Wxl200al User Manual

							
61

Setting
Key	lock
Key	lock
PIN	code	lock
This function locks the side control and remote control buttons 
to prevent operation by unauthorized persons.
  . . . . . .Unlocked.
  . . . . . .Lock the operation of the side control.
To unlock, use the remote control.
   . . . . . .Lock the operation of the remote 
control. To unlock, use the side control.
If the side control accidentally becomes locked and you do 
not have the remote control nearby or there is something 
wrong with your remote control, contact the dealer where you 
purchased the projector or the service center.
This function allows you to use the Key lock and PIN code lock 
function to set the security for the projector operation.
This function prevents the projector from being operated 
by unauthorized persons and provides the following setting 
options for security.
 Off   . . . . .Unlocked.
 On	1   . . . . .Enter the PIN code every time turning on 
the projector.
 On	2   . . . . .Enter the PIN code to operate the projector 
once the power cord is disconnected; as long as 
the AC power cord is connected, the projector 
can be operated without a PIN code.
Whenever you change the PIN code lock setting or the PIN 
code (the four-digit number), you are required to enter the PIN 
code. The "1234" is set as the initial PIN code at the factory. 
If you want to change the PIN code lock setting, Press the 
SELECT button and the PIN code dialog box appears.
PIN	code	lock
Security	(Key	lock	and	PIN	code	lock) 
						

							
62

Setting
Use the Point ▲▼ buttons to select Off, On	1 or On	2. Press the 
SELECT button to close the dialog box.
Change	the	PIN	code	lock	setting
Enter	a	PIN	code
Use the Point ▲▼ buttons to enter a number. Press the Point ► 
button to fix the number and move the red frame pointer to the 
next box. The number changes to . If you fixed an incorrect 
number, use the Point ◄ button to move the pointer to the 
number you want to correct, and then enter the correct number.
Repeat this step to complete entering a four-digit number.
After entering the four-digit number, move the pointer to Set. 
Press the SELECT button so that you can start to operate the 
projector.
If you entered an incorrect PIN code, PIN	code and the number 
() will turn red for a moment. Enter the correct PIN code 
all over again.
Enter	a	PIN	code
The PIN code can be changed to your desired four-digit number.
Press the Point ▼ button to select PIN	code	change and press
the SELECT button. The Current PIN code dialog box appears.
Use the Point ▲▼ buttons to set the current PIN code. The
New PIN code dialog box appears. Set a new PIN code, the
confirmation box appears, and choose yes to set the new PIN
code.
Change	the	PIN	code
CAUTION:
WHEN	 yOU	HAVE	CHANGED	THE	PIN	CODE,	WRITE	DOWN	
THE	NEW	PIN	CODE	IN	COLUMN	OF	THE	PIN	CODE	NO .	
MEMO	ON	PAGE	7,	AND	KEEP	IT	SECUREL y .	IF	 yOU	
FORGET	 yOUR	PIN	CODE,	THE	PROjECTOR	CAN	NO	
LONGER	BE	STARTED .
PIN	code	change	 
						

							
6

Shutter function is available to block out light to the screen, so that \
the screen can be used for the other presenters.
Prohibit the shutter operation from the remote control and the 
projector's side control.
Remote	control   . . 
Selecting On prohibits the shutter 
operation from the remote control.  
Projector. . . .       Selecting On prohibits the shutter   
operation from the side control.
It is possible to prohibit the shutter operation from both of the 
remote control and the side control.
Protection
The Shutter Management function turns off the projection lamp 
when the projector is left with the shutter closed and the set time 
has passed away. The count-down time can be set between 5 
and 480 minutes. When the count-down time has elapsed, the 
shutter will be opened up automatically and the lamp will be 
turned off to cool itself down. The SHUTTER indicator is blinking 
blue during this cooling-off period. When the lamp has been fully 
cooled down, the POWER indicator turns green lighting and the 
SHUTTER indicator keeps blinking. Should the ON / STAND-BY 
button be pressed in this condition, the projection lamp will be 
turned on and the SHUTTER indicator turns off.
Note:
	 		
The	Shutter	Management	function	cannot	be	halted.
Setting
Shutter
Shutter
Management 
						

							
64

When you want to make a digital processing of a projected 
image faster, set this function.
Use the Point ▲▼ buttons, select an item of Off/Low/Mid/High.
Digital processing speed becomes fast by order of Low → Mid → 
High. High is the fastest.
Video	delay	control
Fig .1
Note:
-The	following	functions	are	not	available	respectively	when	Video	delay
control	is	set	to	Low/Mid/High.
Low	...		Keystone	can	not	be	selected.
Mid	...			Progressive	and	Noise reduction	can	not	be	selected.
High	...	Keystone,	Progressive	and	Noise reduction	can	not	
be	selected.-When	Video	delay	control	function	is	set	to Low or	High	and	press	theKEYSTONE	button	on	the	remote	control,	Fig.1	will	be	dispalyed	on	the	bottom	left	screen.Video	delay	:	On
Setting
Closed	caption
Closed Caption is a function that displays the audio portion
of a TV program as text on the screen. If the input signal
contains closed captions, you can turn on the feature and
switch the channels. Press the Point ▲▼ buttons to select Off, 
CC1, CC2, CC or CC4.  
If the Closed caption is not clear, you can change the text from 
Color to White.
Closed	caption
Note:
The	Closed	caption	is	available	only	under	the	situation	below..
	 	• When the input signal is•		When	the	input	signal	is NTSC	of	composite	and	S-video,									and	the	system	is	set	according	to	the	signal	or	set	on	Auto.			 	 •		The	system	must	be	set	on	NTSC	or	Auto	in	Video	System										Selection.	(p.45)			 	 •		The	item	of	Closed	caption	is	displayed	in	gray	while	it	is	not										available.		 	 •		Closed caption	is	unavailable	when	On-Screen	Menu	and										P-timer	are	displayed.
Press the Point ▲▼ buttons to 
select Off, CC1, CC2, CC or CC4, 
and then Press Select button. 
						

							
65

This function returns all setting values except for User	logo, PIN	
code	lock, Logo	PIN	code	lock, Filter	timer and	Filter	counter	to 
the factory default settings.
Various test pattern are available for use when setting up the 
projector.
Filter replacement icon appears on the screen at a set time.
Note:
	 •	 Do	not	reset	the	counter	when	the	filter	or	the	filter	cartridge	is	not	replaced.	 •	 Timer	setting	notifies	that	the	filter	needs	replacement.	To	replace	the	filter,	use	the	filter	control	function	(p.58).
Fig .1   Filter replacement icon
Filter cartridge replacement icon appears on the screen when the filter scroll is counted down to 0 scroll.　　
Fig .4   Filter cartridge replacement icon
Note:
	•	 Fig.1,	Fig.	2,	Fig.	3	and	Fig.	4	appear	at	turning	on	and	selecting	input	source.	 •	 Fig.1,	Fig.	2,	Fig.	3	and	Fig.	4	will	not	appear	when	the	Display	function	is	set	to	Off	(p.52)	or	during	“Freeze”	(p.30).
Last scroll icon appears on the screen when the filter is down to the last scroll.
Fig .   Last scroll icon
Setting
This function is used to set a frequency for the filter replacement.
Use the Point ▲▼ buttons to select Filter	counter and then press 
the Point ► or the SELECT button to access the submenu items. 
 Filter	counter......     Show the total accumulated time of the filter  
use timer setting.
	Timer		................      To set a timer, when the projector reaches  
the time, the Filter replacement icon (Fig.1) 
appears on the screen and the total 
accumulated time turns red, indicating that 
the filter replacement is necessary. If the
filter is out of scroll and the projector reaches
a time set in the timer setting, Fig.2 appears
on the screen, indicating that the filter       
cartridge replacement is necessary.
	Filter	counter	reset..When replacing the Filter cartridge, reset the  
Filter counter and the Scroll remaining (p.68).
 Scrolls	remaining  .  When the filter scroll is counted down to 1,
Scroll remaining on the screen is showing 
0	scroll(s) , the last scroll icon (Fig.3)
appears on the screen. When the filter scroll
is counted down to 0, the Filter cartridge 
replacement icon (Fig.4) appears on the
screen and the WARNING FILTER indicator
lights orange, indicating that the filter cartridge
replacement is necessary.
 Scroll	counter	Reset..When replacing the Filter cartridge, reset the
Filter counter and the Scroll remaining (p.68).
Fig .2
Filter	counter
Press the SELECT button to select Timer and then use the Point ▲▼ buttons to set the timer. Select from (Off/	400H/700H/1000H) depending on the use environment.
Filter	counter
Test	pattern
Factory	default 
						

							
66

Filter prevents dust from accumulating on the optical elements inside th\
e projector. Should the filter becomes clogged with 
dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup and adversely affect the life 
of the projector. This projector has an electrically operated filter which helps you to re\
place the filter easily. The projector 
monitors the condition of the filter at all time and replaces a filter w\
ith a new one automatically when it detects the clogging. 
If the projector reaches a time set in the timer setting (p.65), a Fil\
ter 
replacement icon (Fig.1) appears on the screen and the WARNING 
FILTER indicator on the top panel lights up (p.81). When you see 
this icon, replace the filter as soon as possible (pp.30, 65). If the \
filter is out of scroll and the projector reaches a time set in the 
timer setting, Fig. 2 appears on the screen, indicating that the filter \
cartridge replacement is necessary.
When the filter scroll is counted down to 0, the Last scroll icon 
(Fig.3) appears on the screen, indicating that there is one scroll lef\
t 
in the filter cartridge (p.65).
If the projector detects that the filter is clogged and no scroll is lef\
t 
in the filter cartridge, a Filter cartridge replacement icon (Fig. 4) \
appears on the screen and the WARNING FILTER indicator on the 
top panel lights up (p.81). When you see this icon, replace the filter\
 
cartridge (p.67) and reset the Filter counter (p.68) and the Scroll \
counter (p.68).
When the filter is being scrolled using the remote control (p.30) 
or the Filter control function in the setting menu (p.58), a Filter 
replacement icon and	Please	wait . . . message (Fig.5) appear 
on the screen and the WARNING FILTER indicator blinks slow 
(approx. 2 seconds ON, 2 seconds OFF) (p.81).
The WARNING FILTER indicator blinks fast when the projector 
detects an abnormal condition, the filter cartridge is not installed 
properly, or the filter scroll is not working properly (p.81).
Fig .1   Filter replacement icon
Fig .4   Filter cartridge replacement icon
Fig .   Last scroll icon
Maintenance	and	Care
Note:
 •	 Fig.1,	Fig.2,	Fig.3,	Fig.	4	and	Fig.5	will	not	appear	when	the	Display	function	is	set	to	Off	(p.52)	or	during	“Freeze”	(p.30).	 •	 The	filter	cannot	be	rewound.	 •	 The	filter	can	be	scrolled	9	times	since	the	filter	cartridge	has	10	scrolls.		 •	 The	filter	cartridge	is	disposable.	Do	not	clean	and	reuse	the	filter	cartridge.	 •	 Do	not	expose	the	filter	cartridge	to	water	or	liquid,	or	it	may	cause	a	breakdown.	 •	 Replace	the	filter	cartridge	after	all	the	scroll	is	used	up.	If	you	replace	the	filter	cartridge	when	there	are	some	scrolls	left	in	the	filter	cartridge,	the	filter	counter	and	the	scroll	counter	do	not		recognize	the	correct	number	of	remaining	scrolls	and	the	reset	function	cannot	work	properly.	It	may	cause	a	breakdown.	 •	 Do	not	use	the	filter	cartridge	with	other	projector.	The	filter	counter	and	the	scroll	counter	do	not	recognize	the	correct	number	of	remaining	scrolls	of	the	used	filter	cartridge	and	the	reset	function	cannot	work	properly.	It	may	cause	a	breakdown.
Fig .5   Filter replacement icon and 
Please	wait . . . message. 
	 •	 Make	sure	that	the	projection	lamp	is	turn	off	when	you	are	replacing	the	filter	cartridge.	If	you	replace	the	filter	cartridge		when	the	projection	lamp	is	turn	on,	the	projector	will	be	shut	down	automatically	for	safety	purpose.	 •	Do	not	forget	to	reset	the	filter	counter	and	the	scroll	counter	in	the	setting	menu	after	replacing	the	filter	cartridge.	If	you	forget	to	reset	the	filter	counter	and	the	scroll	counter,	the	projector	cannot	recognize	the	correct	number	of	remaining	scrolls	and	may	cause	a	breakdown.			•	When	the	projector	is	kept	used	for	3	minutes	without	getting	the	filter	cartridge	replaced	after	the	Fig.4	appears	on	the	screen,	the	projector	is	turned	off	automatically	to	prevent	the	damage	of	optical	components.
Fig .2
Filter	Instructions 
						

							
67

Turn off the projector, and unplug the AC power cord from the 
AC outlet.
First, clean up the dust on the projector and around the air 
vents.
1
2
Press ▼ downwards on the filter cover to release the latch 
and open the filter cover.
Put the new one back into the position and close the filter 
cover. Make sure that the filter cartridge is properly and fully 
inserted.
5
CAUTION
Make sure the filter cartridge is inserted in the projector. If 
the filter cartridge is not inserted, the projector cannot be 
turned on. 
Do not put anything into the air vents. Doing so may result 
in malfunction of the projector.
4
Reset the filter counter and the scroll counter (p.68).
6
Filter cover
Pull out the filter cartridge. When taking out the filter cartridge, 
put your finger on the filter cartridge’s tab and then pull.
Latch
Filter cartridgeTab
RECOMMENDATION
We	recommend	avoiding	dusty/smoky	environments	when	
operating	the	projector .	Usage	in	these	environments	may	
cause	a	poor	image	quality  .
When using the projector under dusty or smoky conditions, 
dust may accumulate on a lens, liquid crystal panels, or optical 
elements inside the projector. Such condition may degrade the 
quality of the projected image.
When the symptoms above are noticed, contact your authorized 
dealer or service center for proper cleaning.
Connect  the  AC  power  cord  to  the  projector  and  turn  on  the 
projector.
7
Maintenance	and	Care
Replacing	the	Filter	Cartridge
ORDER	REPLACEMENT	FILTER	CARTRIDGE
Replacement  filter  cartridge  can  be  ordered  through  your  dealer. 
When ordering, give the following information to the dealer.
 ●   Model	No .	of	your	projector
	 	 	 LC-WXL200	
 ●  Replacement	Filter	Cartridge	Type	No .
	 	 															 Service Parts No. 610 346 9034 
						

							
6

Be sure to reset the Scroll counter after replacing the filter cartridge\
. 
Press the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select Setting and then press the 
Point ► or the SELECT button.
Use the Point ▲▼ buttons to select Filter	counter and 
then press the SELECT button. Use the Point ▲▼ buttons 
to select Scroll	counter	reset and then press the SELECT 
button. Scroll	counter	Reset?	appears. Select yes to 
continue.
1
2
Scroll	counter
Another confirmation dialog box appears, select yes to reset 
the Scroll counter.
Filter	counter
Maintenance	and	Care
Be sure to reset the Filter counter after replacing the filter cartridge.
Press the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select Setting and then press the 
Point ► or the SELECT button.
Use the Point ▲▼ buttons to select Filter	counter and 
then press the SELECT button. Use the Point ▲▼ buttons 
to select Filter	counter	reset and then press the SELECT 
button. Filter	counter	Reset?	appears. Select yes to 
continue.
1
2
Filter	counter	Reset? 
appears.
Select yes, then another 
confirmation box appears.
Select yes again to reset 
the Filter counter.
Another confirmation dialog box appears, select yes to reset 
the Filter counter.
Scroll	counter	Reset? 
appears.
Select yes, then another 
confirmation box appears.
Select yes again to reset 
the Scroll counter.
Scroll counter Reset?
Resetting	the	Filter	Counter
Resetting	the	Scroll	Counter 
						

							
69

Filter	counter	Reset? 
appears.
Select yes, then another 
confirmation box appears.
Scroll	counter	Reset?
 
appears.
Select  yes, then another 
confirmation box appears.
Turn off the projector and unplug the AC power cord. Let the 
projector cool for at least 45 minutes.
Loosen the screw and open the lamp cover. Loosen 3 screws 
of the lamp and pull out the lamp by using the built in handle.
1
Replace the lamp with a new one. Make sure that the lamp is 
properly and fully inserted. 
4
2
Connect the AC power cord to the projector and turn on the 
projector.
Follow these steps to replace the lamp.
5
Note:
	 Be	sure	to	insert	the	lamp	in	the	correct	direction.
For continued safety, replace with a lamp  of the 
same type. Do not drop the lamp or touch the glass 
bulb! The glass can shatter and may cause injury.
Allow a projector to cool for at least 45 minutes 
before you open the lamp cover. The inside of the 
projector can become very hot.
CAUTIONCAUTION
When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and the Lamp replacement icon appears on the screen andthe Lamp replacement icon appears on the screen and 
LAMP REPLACE indicator lights orange. Replace the lamp with a new one prompt\
ly. The timing when the LAMP REPLACE 
indicator should light is depending on the lamp mode.
Top	Panel
LAMP 	REPLACE	indicator
Lamp replacement icon
Note:
			The	Lamp	replacement	icon	will	not	appear	when	the	Display	function	is	set	to	Off (p.52)	or	during	“Freeze”	(p.30)
Close the lamp cover and secure the screw. 
Lamp
Handle
Lamp cover
Screw
Maintenance	and	Care
New Lamp
Lamp	Replacement
When replacing the lamp because it has stopped illuminating, 
there is a possibility that the lamp may be broken.
If replacing the lamp of a projector which has been installed 
on the ceiling, you should always assume that the lamp is 
broken, and you should stand to the side of the lamp cover, 
not underneath it. Remove the lamp cover gently. Small 
pieces of glass may fall out when the lamp cover is opened.
If pieces of glass get into your eyes or mouth, seek medical 
advice immediately.
CAUTION
Screws 
						

							
70

Maintenance	and	Care
This projector uses a high-pressure lamp which must be handled carefully\
 and properly. 
Improper handling may result in accidents, injury, or create a fire hazard.
● Lamp  lifetime  may  differ  from  lamp  to  lamp  and  according  to  the  environment  of  use.  There  is  no 
guarantee  of  the  same  lifetime  for  each  lamp.  Some  lamps  may  fail  or  terminate  their  lifetime  in  a 
shorter period of time than other similar lamps.
● If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights up, 
replace  the  lamp  with  a  new  one  IMMEDIATELY  after  the  projector  has  cooled  down.  (Follow  carefully 
the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp with the 
LAMP REPLACE indicator lighted may increase the risk of lamp explosion.  
● Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime 
draws  to  an  end.  Risk  of  explosion  may  differ  according  to  the  environment  or  conditions  in  which  the 
projector and lamp are being used.
IF	 A	LAMP 	EXPLODES,	THE	FOLLOWING	SAFETy	PRECAUTIONS	SHOULD	BE	TAKEN .
If  a  lamp  explodes,  disconnect  the  projector ’s  AC  plug  from  the  AC  outlet  immediately.  Contact  an 
authorized  service  center  for  a  checkup  of  the  unit  and  replacement  of  the  lamp.  Additionally,  check 
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out 
from  the  cooling  air  circulation  holes.  Any  broken  shards  found  should  be  cleaned  up  carefully.  No  one 
should  check  the  inside  of  the  projector  except  those  who  are  authorized  trained  technicians  and  who 
are  familiar  with  projector  service.  Inappropriate  attempts  to  service  the  unit  by  anyone,  especially  those 
who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken 
glass.
										LAMP 	HANDLING	PRECAUTIONS
ORDER	REPLACEMENT	LAMP
Replacement lamp can be ordered through your dealer. When ordering, give the following information to the 
dealer.
 ●   Model	No .	of	your	projector	 :LC-WXL200	
 ●  Replacement	Lamp	Type	No .	 :POA-LMP16		
               (Service Parts No. 610 346 9607)