Eiki Projector Lc Wxl200a User Manual

							51
Setting
Setting Menu
Press the MENU button to display the On-Screen Menu.  
Press the Point ▲▼ buttons to select Setting and press the 
Point ► or the SELECT button to access the submenu items.
1
2Use the Point ▲▼ buttons to select the desired item and 
then press the Point ► or the SELECT button to access the 
selected item.
This projector has a Setting menu that allows you to set up the 
other various functions described below.
3Use the Point ▲▼ buttons to select the desired item and 
then press the SELECT button.
The language used in the On-Screen Menu is available in English, 
German, French, Italian, Spanish, Portuguese, Dutch, Swedish, 
Russian, Chinese, Korean and Japanese.
Language
This function is used to change the position of the On-Screen Menu. 
Select Menu position and press the SELECT button.
The Menu position changes each time you press the SELECT button 
as follows.
the center → the bottom left → the bottom right → the top left → the 
top right → the center → .....
This function detects the input signal automatically. When a signal is 
found, the search will stop. Use the Point ▲▼ buttons to select one 
of the following options.
Mode 1......Input search will dose not work.
Mode 2......Input search works under the following situation:
 – When pressing the INPUT button on the side control.  
    or the remote control.
Mode 3......Input search works under the following situation:
 – When turning on the projector by pressing the ON/
STAND-BY button on the side control or pressing the 
ON button on the remote control.
  – When pressing the INPUT button on the remote 
control or on the side control.
  – When no signal is detected.
Note:
	 •While	Input button	is	set	to	Mode 3,	and	no	signal	is	
detected,	if	the	Shutter	or	Freeze	function	is	active,	cancel	
it	to	activate	the	Input	search.
	 •While	Input	button	is	set	to	Mode 1	or	Mode 2,	the	status	
of	Input	and	Lamp	are	displayed	every	time	the	signal	is	
switched.
	 •Only	the	last	selected	input	source	can	be	detected.
	 •If	the	INPUT,	INPUT	1,	INPUT	2,	INPUT	3,	ON	/	STAND-
BY 	or	MENU	button	is	pressed	during	Input	search	is	
in	progress,	Input	search	will	stop	and	go	back	to	the	
previous	input	signal.
Setting
Language
Menu position
Input button 
						

							52
This function decides whether to display On-Screen Displays.
 On ...............................  Show all the On-Screen displays. Use this 
function when you want to project images 
after the lamp becomes bright enough. The 
factory default setting is in this option.
 Countdown Off ..........  Show the input image instead of the 
countdown when turning on the projector. 
Use this function when you want to project 
the image as early as possible even when 
the lamp is not bright enough.
 Off ...............................  Hide the On-Screen Displays except;
  ● On-Screen Menu
  ● Power off? (p.24)
  ● No signal for Power management    
  (p.59)
  ● Please wait  . . .
  ● White Arrows for panning mode (p.42)
                                         ● P-timer
  ● Simple mode
  ● Video delay control
  ● Picture in Picture
  ● Service
Setting
Select the background screen for when no input signal is detected. 
Press the Point ▲▼ buttons to switch between each option.
 Blue....  Project a blue background.
 Black ... Project a black background.
                    It is invalid when there is no image.
 User.... Project an image captured in the Logo setting.
Logo select
This function allows you to customize the screen logo with Logo 
select, capture, Logo PIN code lock and Logo PIN code change 
functions.
Note:
	 		When	On	is	selected	in	the	Logo	PIN	code	lock	function,	Logo select,	
Capture	and	Logo PIN code change	cannot	be	selected.
Logo select
This function decides on the starting-up display from among 
following options. 
 User ..........  Show the image you captured. 
 Default ......  Show the factory-set logo. 
 Off .............  Show the countdown display only.
Display
Background
Logo (Logo and Logo PIN code lock settings) 
						

							53
Setting
Capture
Capture
This function enables you to capture an image being projected to 
use it for a starting-up display or interval of presentations.
Select Capture and press the SELECT button.  
A confirmation box appears and select yes to capture the projected 
image.
After capturing the projected image, go to the Logo select function 
and set it to User. Then the captured image will be displayed the 
next time you turn on the projector.
To cancel the capture function, select yes in the "Quit?" confirmation 
box.
Note:
	 •	Before	capturing	an	image,	select	Standard	in	the	Image	Select	
Menu	to	capture	a	proper	image	(pp.40,	46).
	 •	A 	signal	from	a	computer	can	be	captured	up	to	WXGA 	(1280	x	
800).	A	signal	from	video	equipment	can	be	captured	except	for	
1035i,	1080i and	1080p.
	 •	When	capturing	the	image	that	has	been	adjusted	by	the	
Keystone	function,	the	adjusted	data	is	automatically	reset	and	
the	projector	captures	an	image	without	keystone	correction.	
	 •	When 	Logo  PIN  code  lock	is	 set	 to	On,	Capture	cannot 	be	
selected.			
	 •	When	starting	to	capture	a	new	image,	the	previously	stored	
image	is	cleared	even	if	you	cancel	the	capturing.
		•	 When	there	is	no	captured	image	or	it	is	interrupted	while	
capturing	an	image,	User	cannot	be	selected,	you	can	only	
switch	between	Default	and	Off.
		•	Capture	function	is	not	available	when	the	Picture	in	Picture	
function	is	set	to	User1-5.
Logo PIN code lockThis function prevents an unauthorized person from changing the 
screen logo.
 Off .............  The screen logo can be changed freely from the 
Logo Menu (p.52).
 On .............  The screen logo cannot be changed without a Logo 
PIN code.
If you want to change the Logo PIN code lock setting, press the 
SELECT button and the Logo PIN code dialog box appears. Enter 
a Logo PIN code by following the steps below. The initial Logo PIN 
code is set to "4321" at the factory.
Logo PIN code lock 
						

							54
Setting
Enter a Logo PIN code
Use the Point ▲▼ buttons to enter a number. Press the Point ► 
button to fix the number and move the red frame pointer to the next 
box. The number changes to . If you fixed an incorrect number, 
use the Point ◄ button to move the pointer to the number you 
want to correct, and then enter the correct number.
Repeat this step to complete entering a four-digit number.
After entering the four-digit number, move the pointer to Set. Press 
the SELECT button so that you can start to operate the projector.
If  you  entered  an  incorrect  Logo  PIN  code, Logo  PIN  code  and 
the  number  ()  will  turn  red  for  a  moment.  Enter  the  correct 
Logo PIN code all over again.
Use the Point ▲▼ buttons to switch On or Off, and then press the 
SELECT button to close the dialog box.
Change the Logo PIN code lock setting
Enter a Logo PIN code
After a correct Logo PIN code 
is entered, the following dialog 
box appears.
CAUTION:
WHEN yOU HAVE CHANGED THE LOGO PIN CODE, WRITE 
DOWN THE NEW PIN CODE IN COLUMN OF THE LOGO PIN 
CODE NO . MEMO ON PAGE 87, AND KEEP IT SECUREL y . 
SHOULD  THE LOGO  PIN CODE  BE LOST  OR FORGOTTEN,  THE 
LOGO PIN CODE SETTING CAN NO LONGER BE CHANGED .
Change the Logo PIN code lock setting
Logo PIN code change
Change the Logo PIN code
Logo PIN code can be changed to your desired four-digit 
number. Press the SELECT button to select Logo PIN code 
change. Current logo PIN code dialog box appears, use the 
Point ▲▼ buttons to enter the correct code. The New Logo 
PIN code input dialog box appears. Set a new Logo PIN code, 
confirmation box appears, choose yes to set the new Logo PIN 
code.
Be sure to note the new Logo PIN code and keep it on hand. If 
you lost the number, you could no longer change the Logo PIN 
code setting.  
						

							55
Setting
Picture in PicturePicture in PictureSelected Mode
Status (Stored /Free/ Adj .) of the selectedmode.
Position Menu
Active frame
(White)
Center line
display
Note:
 •	The	Picture	in	Picture	function	is	not	available	depending	on	the	input	signals	and	the	selected	input	terminals.	Refer	to	‘List	of	Picture	in	Picture‘	for	details	(p.89).	 •	When	the	input	signal(s)	is/are	incompatible,	X mark	will	be	displayed	on	the	Main/Sub	picture.
This function is used to project two images simultaneously by
placing a separate small sub screen within or next to the main screen.
Use the Point ▲▼ buttons to select Picture in Picture and then 
press the SELECT button to display a dialog box. You can also 
display the dialog box by pressing and holding the PIP button on the 
remote control for more than 3 seconds.
Only the sound from the source of Main picture is valid, while the 
source of Sub picture cannot output the sound ( In P in P, the larger 
picture is main picture, and the smaller one is sub picture; in P by P, 
the left picture is main picture, and the right one is sub picture.).
 
Show the selected mode (Off/User 1-5) and its status (Stored 
/Free/ Adj .). User 1 and User 2 have stored default values. See 
page 30 for details.
  User setting
P in P:  Provide the images of Main picture and Sub picture 
             at the ratio of Screen aspect in the Screen Menu. 
P by P: Provide the images of Main picture and Sub picture 
             at the ratio of 4:3.
  P in P/P by P
  Main picture / Sub picture
Input......Select an input from Input 1-3. Source...Select an input source. The display varies depending               on the selected input.Size...... Select the display size. Main picture can be changed                 between 10 and 100%, and Sub picture can be                changed between 10 to 50% in increments of 10%.               When P by P is selected in Mode, the projection size is               fixed to 50%.Position..Press the SELECT button at Position and the display                position setting screen appears.
Use the Point ▲▼◄► buttons to adjust the display position of active frame indicated in white. The frame will disappear after 10 seconds or when the SELECT button is pressed.
Selecting the Main picture or Sub picture
During Picture in Picture mode, and being undisplayed On Screen 
Menu, press the SELECT button to select Main or Sub picture. (A red 
frame will be displayed on the selected picture.)
Switching Input and Source
When selecting Main picture or Sub picture, input and source can be 
set by pressing the INPUT button on the side control or INPUT 1/2/3 
button on the remote control. Operation on the On Screen Menu is not 
necessary.
Note:
 •	When	PIP	is	selected,	screen	is	not	available. 
						

							56
This function is only used for HDMI input source.
  Image
Select Normal or Enhanced to match the video range 
setting of your HDMI Digital RGB equipment.
  Sound
        HDMI : When using the HDMI cable, select HDMI.  
                   Both video and audio are transferred and you 
                   need not to connect any additional cables for 
                   audio. 
   AUDIO 1: When using the DVI-HDMI cable, select   
                   AUDIO 1 and connect the audio cable to 
                   AUDIO IN 1.
The names for the output setting of Digital RGB vary from 
equipment to equipment. For details, refer to the owner’s 
manual of your Digital RGB equipment.
When the black parts of the image are destroyed or stand
out, please switch to Normal or Enhanced, and then switch
the output type of the HDMI Digital RGB output equipment.
HDMI setup
HDMI setup
Set the Frame Lock to Main picture or Sub picture.
  Frame lock
Press the SELECT button at Reset to display a confirmation box. To 
reset, press the SELECT button at yes.
  Reset
Delete the data stored in the Mode and return to Free. Use the Point 
▲▼ buttons to select Mode free and press the SELECT button to 
show the Where to free? dialog box. Move the highlight to one of the 
mode (User1 - 5) which you want to delete and press the SELECT 
button. Then the confirmation box appears. To delete, select yes. 
  Mode free
Setting
Store the adjusted data in the User 1-5. Use the Point ▲▼ buttons 
to select Store and press the SELECT button to show the Where 
to store? dialog box. Move the highlight to one of the mode (User1 
- 5) which you want to store and press the SELECT button. Then the 
confirmation box appears. To store adjusted data, select yes. 
  Store
To store the adjusted data.
Stored data
Vacant
Return to Picture in Picture menu. 
						

							57
This function allows you to change brightness of the screen.
Lamp controlLamp control
Select the lamp operation when the total lighting time of a lamp 
exceeds the recommended total hours of use.
     Mode 1 ............  A lamp can be turned on even after
                               exceeding the recommended total hours of \
use.
     Mode 2 ............  A lamp can be turned on even after 
exceeding the recommended total hours of 
use. But the projector turns off automatically 
after 3 minutes.
Lamp life control
Note:
•  	Lamp	mode	cannot	be	changed	for	a	while	after	turning	on	the	
projector.	Lamp	needs	some	time	to	stabilize	after	the	power	
is	turned	on.	Stored	lamp	mode	will	be	active	after	the	lamp	is	
stabilized.
•  	If	Mode 2 has	been	selected	and	the	projection	lamp	
				exceeds	the	recommended	total	hours	of	use,	the	
				replacement	icon	will	be	displayed	at	the	time	of	power-on.	
			Then	the	projector	will	turn	off	after	3	minutes.
    The Lamp replacement icon will not appear when the Display 
function is set to Off (p.52), during Freeze (p.30), or Shutter 
(p.27).
Lamp replacement icon
Setting
Auto ..... Brightness according to the input signal. 
Normal ... Normal brightness. 
Eco 1 ....  Lower brightness and decrease of fan speed. 
Lower brightness reduces the lamp power 
consumption and extends the lamp life.
Eco 2 ....  Lower brightness and increase of fan speed. 
Lower brightness reduces the lamp power 
consumption and extends the lamp life. It is 
recommended to use Eco 2 when using the 
projector continuously over a long period of time. 
The fan noise becomes louder in Eco 2 than in 
Eco 1. Select the suitable mode for the used 
environment. 
Lamp control 
Note:
	 The	fan	noise	becomes	louder	in	Eco	2	than	in	Eco	1.	
		Select	the	suitable	mode	for	the	used	environment. 
						

							58
Choose the running speed of cooling fans from the following options.
 Normal ......  Operate in this mode under normal conditions.
 Max ...........  Use this mode when you want to increase the cooling 
effect when operating the projector in high ambient 
temperature environment. Fan noise is louder than 
Normal. 
Setting
Simple mode buttons
Filter control
This function decides whether to activate the simple mode.
 Off .... Simple mode function is off.
 On .... Only the simple mode buttons are active.
You can replace the filter with this function. Press the SELECT 
button at Filter control to display a confirmation box. To replace, 
press the SELECT button at y es and the electrically operated filter 
starts to scroll.
Note:		•		Filter	replacement	icon	and Please wait... message	appear	on	the	screen							when	the	filter	is	being	scrolled.		•	The	filter	cannot	be	rewound.		•	When	the	filter	is	replaced,	the	total	accumulated	time	of	the	filter	use	is					automatically	set	to	0.
A confirmation box appears and 
then select yes.
The eight different remote control codes (Code 1-Code 8) are 
assigned to the projector; the factory-set, initial code (Code 1) and 
the other seven codes (Code 2 to Code 8). 
The same code should be set on both the projector and the remote 
control. For example, operating the projector in Code 7, the remote 
control code also must be switched to Code 7.
 To change the code for the projector
  Select a remote control code in this Setting Menu.
 To change the code for the remote control:
  Press and hold the MENU button and a number button (1-8) on   
  the remote control for more than five seconds to switch between 
  the codes. See “Remote Control Code” on page 16.
Note:
•	When	different	codes	are	set	on	the	projector	and	on	the	remote	
		control,	any	operation	cannot	be	made.	In	that	case,	switch	the	code	on	
		the	remote	control	to	fit	the	code	on	the	projector.
Filter control
Fan control
Simple mode
Remote control
   
Note:
  				Warning	icon	and	Simple mode : On	message	appear	on	the	screen	for	 about	4	seconds	when	press	the	button	which	is	not	the	simple	mode	button.
Only these buttons are active 
when the simple mode is 
set to On. [ON, STAND-BY, 
SHUTTER, INPUT, MENU, 
AUTO PC, SCREEN, ▲, 
▼ (MUTE), ◄ (VOLUME-), 
► (VOLUME+), SELECT 
(Mouse Pointer included), 
L-CLICK, R-CLICK, P-TIMER, 
POINTER, PIP, ON-OFF 
switch] Number buttons (p.14) 
also become active only when 
setting the remote control 
codes numbers or entering the 
PIN code numbers (pp. 54, 62). 
						

							59
Note:
	 •	Factory	default	is	Ready: 5 Min.	 •		
When	the	shutter	is	closed	while	the	Power	management	function	is	working,	the	Power	management	function	is	released.
Setting
Select a location of the infrared remote receiver of the remote control.\
 See “Remote Control Receivers and Operating Range” on page 15 for \
details.
 All...........................Activate all of the receivers.
 Front & Top...........Activate both the front and top receivers.
 Top & Back ...........Activate both the top and back receivers.
 Front & Back ........Activate both the front and back receivers.
 Front......................Activate only the front receiver.
 Top.........................Activate only the top receiver.
 Back.......................Activate only the back receiver.No  signal
4 : 50
Timer left before Lamp is off.
Power management
For reducing power consumption as well as maintaining the lamp life, 
the Power management function turns off the projection lamp when 
the projector is not operated for a certain period.
Select one of the following options:
 Ready  ..................  When the lamp has been fully cooled down, the 
POWER indicator changes to green blinking. In 
this condition, the projection lamp will be turned 
on if the input signal is reconnected or any 
button on the side control or remote control is 
pressed. 
 Shut down ...........  When the lamp has been fully cooled down, the 
power will be turned off. 
 Off ........................ Power management function is off. 
 Timer....................  If the input signal is interrupted and no button 
is pressed for more than 30 seconds, the timer 
display with No signal appears. It starts the 
countdown until the lamp is turned off. Use the 
Point ▲▼ buttons to set the Timer(1~30Min).
This function is available when operating the projector via network.
 Network ..........  Supply the power to the network function 
even after turning off the projector. You can turn 
on/off the projector via network, modify network 
environment, and receive an e-mail about projector 
status while the projector is powered off.
  Eco.................... Select Eco when you do not use the projector 
via network. The projector’s network function will 
stop when turning off the projector.
Refer to the owner’s manual of “Network Set-up and Operation”.
Note:
•	Factory	default	is	Network.
•	When	selecting	Network,	the	cooling	fans	may	be	running	depending
		on	the	temperature	inside	the	projector	even	if	the	projector	is	turned	off.
•	When	Eco	is	selected	and	the	projector	is	in	Stand-by,	the	communication	
		of	RS-232C	serial	port	is	not	available.
RC sensor
Power management
Standby mode 
						

							60
Setting
When this function is set to On, the projector will be automatically 
turned on just by connecting the AC power cord to the wall outlet.
Note:
				 Be	sure	to	turn	off	the	projector	properly	(see	“Turning	Off	the	Projector”	on	page	24).	If	the	projector	is	turned	off	in	the	incorrect	sequence,	the	Direct	on	function	does	not	work	properly.
You can emphasize a part of the projected image with this function. 
Use the Point ▲▼ buttons to select a pattern of the Pointer (Arrow, 
Finger, or Dot) (p.32).
This function allows you to change the presentation of the P-timer 
and execute it.
Select one of the following options:
 Count up .............  The P-timer display 000:00 appears on the 
screen and the count starts (000:00–180:00).
 Count down ........  The time set in the Timer setting appears on the 
screen and the countdown starts.
 Timer.................... Use the Point ▲▼ buttons to set the Timer 
(1–180 Min). Only set to Count down, Timer is 
active. Factory default value is 10 Min.
 Start .....................  It executes the count up or count down 
function. Press the SELECT button at Start, 
Start changes to Stop in the Screen Menu. At 
that time, press the SELECT button at Stop 
to stop Count up or Count down,  and Stop 
changes to Restart in the Screen Menu. Press 
the SELECT button at Restart to resume 
Count up or Count down.
 Reset ...................  Reset the P-timer values.
                                  Press the SELECT button at Reset to return to 
the following value;
                                  Count up ... "000:00"
                                  Count down ... Timer that you set
 Exit .......................  To exit the P-timer operation.
Stop or Cancel the P-timer via Remote Control
To stop the P-timer, press the P-TIMER button.
To cancel the P-timer, press and hold the P-TIMER button for a few 
seconds.
P-TIMER
P-timer display
Direct on
Pointer
P-timer