Eiki Projector Lc Wxl200a User Manual

							41
Computer Input
Image adjust MenuPress the MENU button to display the On-Screen Menu. 
Use the Point ▲▼ buttons to select Image adjust and 
then press the Point ► or the SELECT button.
1
2Use the Point ▲▼ buttons to select the desired item 
and then press the SELECT button to display the 
adjustment dialog box. Use the Point ◄► buttons to 
adjust the setting value.
Note:
 When	White	balance	Red,	Green	or	Blue	is		
	adjusted,	Color temp.	will	change	to	Adj..
Press the Point ◄ button to decrease the contrast; press the Point 
► button to increase the contrast (from 0 to 63).
Press the Point ◄ button to decrease the brightness; press the 
Point ► button to increase the brightness (from 0 to 63).
Press the Point ◄ button to lighten red tone; press the Point ► 
button to deepen red tone (from 0 to 63).
Press the Point ◄ button to lighten green tone; press the Point ► 
button to deepen green tone (from 0 to 63).
Press the Point ◄ button to lighten blue tone; press the Point ► 
button to deepen blue tone (from 0 to 63).
Use the Point ◄► buttons to select the desired Color temp. level 
(XLow, Low, Mid or High). 
Use the Point ◄► buttons to adjust the gamma value to obtain a 
better balance of contrast (from 0 to 15).
Press the Point ◄ button to decrease the sharpness of the image; 
press the Point ► button to increase the sharpness of the image 
(from 0 to 31).
Use the Point ◄► 
buttons to adjust the 
setting value.
Selected Image mode
Press the Point ◄ button to lighten red/green/blue tone of the black 
level of an image; press the Point ► button to deepen red/green/
blue tone of the black level of an image.
Image Adjustment
Contrast
Brightness
Color temp .
White balance (Red)
White balance (Green)
White balance (Blue)
Offset(Red/Green/Blue)
Sharpness
Gamma
This iris function effectively increase the contrast intensity. Press 
the Point ◄► buttons to select Off or On.
Off ...... Disabled.
On ...... Contrast is prioritized over brightness.
Iris 
						

							42
Select the desired screen size that conforms to the input signal 
source.
SCREEN MENU
1
2
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Screen and then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons select the desired item and then press the SELECT button.
To reset the adjusted data, select Reset and press the SELECT 
button. A confirmation box appears and then select yes. All 
adjustments will return to their previous figures. 
To store the adjusted data, select Store and press the Point ► or 
the SELECT button. Use the Point ▲▼ buttons to select one from 
Image 1 to 10 and press the SELECT button. 
A confirmation box appears and then select yes. Stored data can 
be called up by selecting an Image (1-10) in the Image Mode 
Selection on page 40.
A confirmation box appears and 
then select yes.
Store
Computer Input
Reset
Store
Screen Size Adjustment
Provide the image within a screen size keeping its original aspect ratio\
.
Note:
		 •	The	projector	cannot	display	any	resolution	higher	than	1920	x	1200.	If	your	computer’s	screen	resolution	is	higher	than	1920	x	1200,	lower	the	resolution	before	connecting	the	projector.	 •	The	image	data	other	than	1280x	800	is	modified	to	fit	the	screen	size	in	initial	mode.	 •	Full, Wide(16:9),	Zoom, True and	Digital zoom +/– cannot	be	selected	when	no	signal	is	detected	in	the	PC	System	Menu.	(p.36)
Normal
Provide the image in its original size. When the original image size is larger than the screen size (1280 x 800), the projector enters to the panning mode automatically. Use the Point ▲▼◄► buttons to pan the image. When adjusted, the arrows will turn red. When reached to the correction limits, the arrows will disappear.
Scale the image proportionally to fit the entire screen. Either side of \
image may go over the screen.
True
Zoom
Provide the image to fit full screen size.
Full 
Provide the last stored aspect screen image. 
Custom
Provide the image at the 16:9 wide screen ratio.
Wide (16:9) 
						

							43
Computer Input
Note:
 •	When	no	signal	is	detected,	Normal	is	set	automatically	and	the	Aspect	dialog	box	disappears.	 •	The	adjustable	range	for	Scale H/V	and	Position H/V	is	limited	depending	on	the	input	signal.
Custom adj .Custom adj .
Select Digital zoom +. The On-Screen Menu disappears and D . zoom 
+  appears.  Press  the  SELECT  button  to  expand  the  image  size.  Use 
the Point ▲▼◄► buttons to pan the image. The Panning function can 
work only when the image is larger than the screen size.
You can also enter the Digital zoom + mode by pressing the D.ZOOM 
button on the remote control.
You can also enter the Digital zoom - mode by pressing the D.ZOOM 
button on the remote control.
Select Digital zoom – . The On-Screen Menu disappears and D . zoom 
– appears. Press the SELECT button to compress image size. 
The projected image can be also compressed by pressing the D.ZOOM 
button on the remote control.  
To return to the previous screen size, select a screen size from the 
Screen  Size  Adjustment  Menu  or  select  an  input  source  from  the 
Input  Source  Selection  Menu  (see  pages  33-35)  again  or  adjust 
the screen size with the D.ZOOM button.
Digital zoom +
Digital zoom -
Adjust the screen scale and position manually with this function.
Press the Point ►button or the SELECT button at Custom adj . 
and Custom adj . is displayed on the screen, you can use the Point 
▲▼ buttons to choose the item you want to adjust.
 Scale H/V .............  Adjust the Horizontal/Vertical screen scale.
 H&V ......................  When set to On, the aspect ratio is fixed. 
Scale V appears dimmed and becomes 
unavailable. Adjust Scale H, then the screen 
scale is automatically modified based on the 
aspect ratio. 
 Position H/V ........  Adjust the Horizontal/Vertical screen position.
 Common ..............  Save the adjusted scale to all the inputs. 
Press the SELECT button at Common to 
display a confirmation box. To save the scale, 
press the SELECT button at y es. When 
Custom is selected, the saved scale is used.
 Reset ...................  Reset all the adjusted values. Press the 
SELECT button at Reset to display a 
confirmation box. To reset, press the SELECT 
button at y es.
Note:
 •	The	panning	function	may	not	operate	properly	if	the	
stored	Mode	in	the	PC	adjust	Menu	is	used	(p.39).
		•	The	minimum	compression	ratio	is	limited	depending	
on	the	input	signal,	when	the	Keystone	function	is	
working	or	when	the	custom	is	selected	for	the	screen	
size.
	 •	True	and	Digital zoom +/– cannot	be	selected	when	
480i,	575i,	480p or	575p	is	selected	in	the	PC	System	
Menu	(p.36).
	 •	Digital zoom +/-	cannot	be	selected	when	True	is	
selected.
		•	Digital zoom – cannot	be	operated	when	Custom	is	
selected. 
						

							44
Computer Input
This function is used to adjust keystone distortion of the projected 
image. Use the Point ▲▼ buttons to choose the item you want to 
adjust.Keystone
This function returns all adjusted values to the factory default 
settings. Press the SELECT button at Reset to display a 
confirmation box. To reset, press the SELECT button at yes.
Ceiling 
Rear 
When this function is set to On, the picture will be top/bottom and 
left/right reversed. This function is used to project the image from a 
ceiling-mounted projector.
When this function is set to On, the picture will be left/right 
reversed. This function is used to project the image from rear of 
the screen.
Keystone
Ceiling
Rear
Reset
Adjust the Horizontal/Vertical keystone distortion of the  projected 
image.
Standard 
 Corner correction
Adjust the corner distortion of the projected image.
Corner pattern
Choose a Corner pattern mode among Red, White, Blue, 
and Off.  
 Store
    Store .......Keep the keystone correction even when the AC 
                      power cord is unplugged.
  Reset  .......Release the keystone correction when the AC
                      power cord is unplugged.
Press the KEYSTONE button on the remote control to switch the 
Standard (for Vertical/Horizontal) /Corner correction adjustment. The 
Standard or Corner correction adjustment dialog box appears. Use 
the Point ▲▼◄► buttons to correct the Standard or Corner distortion 
(p.31). 
Screen aspect
This function is used to project the image to a 4:3 or 16:9 
projection screen.
Default (16:10) ....16:10 is the aspect of the LCD panel. The 
                              original Screen Menu is available.
16:9 ......................Set to a 16:9 projection screen.
4:3 ........................Set to a 4:3 projection screen.Note:
-	Natural wide	cannot	be	selected	when	720p,	1035i,	1080i 		or	1080p	is	selected	on	 AV	System	Menu	(p.45).-	When	the	16:9	function	is	selected,	Wide(16:9)	is	not			available	in	the	PC	and	 AV	screen	(pp.42-44,	49).-	When	the	4:3	function	is	selected,	Natural wide	is	not			available	in	the	AV	screen	(p.49).	 
						

							45
If the projector cannot reproduce proper video image, select a 
specific broadcast signal format from among PAL, SECAM, NTSC, 
NTSC 4 .43, PAL-M, and PAL-N.
The projector automatically detects an incoming video signal, and 
adjusts itself to optimize its performance.
When the Video System is 1035i, 1080i or 1080p, select the 
system manually.
If the projector cannot reproduce proper video image, select a 
specific component video signal format from among 480i, 575i, 
480p, 575p, 720p, 1035i, 1080i, and 1080p.
Video jack or S-video jack
The projector automatically detects an incoming video system, and 
adjusts itself to optimize its performance.
When Video System is PAL-M or PAL-N, select the system 
manually.
Video Input
1AV System Menu (Video or S-video)
AV System Menu (y, Pb/Cb, Pr/Cr)
2
Press the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select Input and then press the Point 
► or the SELECT button. 
Use the Point ▲▼ buttons to select System and then press the 
Point ► or the SELECT button. 
3Use the Point ▲▼ buttons to select the desired system and 
then press the SELECT button.
Note:
The	AV	System	Menu	cannot	be	selected	when	selecting	
RGB (Scart).
Video System Selection
Auto
y, Pb/Cb, Pr/Cr jacks
Auto
PAL/SECAM/NTSC/NTSC4 .43/PAL-M/PAL-N
y, Pb/Cb, Pr/Cr SIGNAL FORMAT 
						

							46
Normal picture level preset on the projector.
Picture level adjusted with fine tone.
User preset picture adjustment in the Image adjust Menu (p.48).
Video Input
Image select Menu
1
2
Press the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select Image select and then press 
the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired item and 
then press the SELECT button.
Image Level Selection
Menu Operation
Standard
Cinema
Image 1–10
For viewing pictures in a bright room.
Dynamic
Naturally picture level preset on the projector.  
Natural 
						

							47
1
2
Press the Point ◄ button to decrease the contrast; press the Point 
► button to increase the contrast (from 0 to 63).
Press the Point ◄ button to decrease the brightness; press the 
Point ► button to increase the brightness (from 0 to 63).
Press the Point ◄ button to lighten red tone; press the Point ► 
button to deepen red tone (from 0 to 63).
Press the Point ◄ button to lighten green tone; press the Point ► 
button to deepen green tone (from 0 to 63).
Press the Point ◄ button to lighten blue tone; press the Point ► 
button to deepen blue tone (from 0 to 63).
Use the Point ◄► buttons to select the desired Color temp. level 
(XLow, Low, Mid or High). 
Press the Point ◄ button to decrease the intensity of the color; 
press the Point ►button increase the intensity of the color (from 0 
to 63).
Press the Point ◄► buttons to adjust the tint value to get a proper 
color balance (from 0 to 63).
Note:
	•	When	White	balance	Red,	Green	or	Blue	is	adjusted,	the	Color	temp.	level	will	change	to	Adj..
	•	Tint cannot	be	selected	when	the	video	system	is	PAL,	SECAM,	PAL-M or	PAL-N (p.45).
Image adjust Menu
Selected Image mode
Press the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select Image adjust and then press 
the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired item and 
then press the SELECT button to display the adjustment 
dialog box. Use the Point ◄► buttons to adjust the setting 
value.
Use the Point ◄► 
buttons to adjust the 
setting value.
Video Input
Image Adjustment
Contrast
Brightness
Color
Tint
Color temp .
White balance (Green)
White balance (Red)
White balance (Blue)
This iris function effectively increase the contrast intensity. Press 
the Point ◄► buttons to select Off or On.
Off ...... Disabled.
On ...... Contrast is prioritized over brightness.
Iris 
						

							48
Use  the  Point  ◄►  buttons  to  adjust  the  gamma  value  to  obtain  a 
better balance of contrast (from 0 to 15).
Press the Point ◄ button to decrease the sharpness of the image; 
press the Point ► button to increase the sharpness of the image 
(from 0 to 31).
An interlaced video signal can be displayed in progressive mode. 
Press the Point ◄► buttons to change the progressive scan mode.
 Off ...........  Progressive scan mode is Off.
 On ...........  Progressive scan mode is On .
 Film .........  For watching a film. With this function, the projector 
reproduces pictures faithful to the original film quality.
Noise interference on the screen can be reduced. Press the Point 
◄► buttons to change the noise reduction mode.
 Off ...........  Noise reduction mode is Off.
 On ...........  Noise reduction mode is On.
Note: 
	 •	Progressive cannot	be	selected	when	480p, 575p, 720p, or 
1080p is	selected	(p.45).
		•	Noise reduction cannot	be	selected	with	the	computer	input	
and	when	the	video	signal	format	is 1080p.	(p.45).
To reset the adjusted data, select Reset and press the SELECT 
button. A confirmation box appears and then select y es. All 
adjustments will return to their previous figures. 
To store the adjusted data, select Store and press the Point ► or 
the SELECT button. Use the Point ▲▼ buttons to select one from 
Images 1 to 10 and press the SELECT button. 
A confirmation box appears and then select yes. Stored data can 
be called up by selecting an Image (1-10) in the Image Mode 
Selection on page 46.
A confirmation box 
appears and then 
select yes.
Store
Video Input
Press the Point ◄ button to lighten red/green/blue tone of the 
black level of an image; press the Point ► button to deepen red/
green/blue tone of the black level of an image (from 0 to 63).
Offset(Red/Green/Blue)
Sharpness
Gamma
Noise reduction
Progressive
Reset
Store 
						

							49
Video Input
Custom adj .
1
2
Press the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select Screen and then press the 
Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired item 
and then press the SELECT button.
Screen Size Adjustment
Note:
	 •	 When	no	signal	 is	detected,	Normal	is	 set	 automatically	and	the	 Aspect	dialog	box	disappears.	 •	 The	adjustable	range	for	Scale	H/V	and	Position	H/V	are	limited	depending	on	the	input	signal.	 •	Natural wide	cannot	be	selected	when	720p,	1035i,	    1080i	or	1080p	is	selected	on	 AV	System	Menu	(p.45).
Provide the image within a screen size keeping its original aspect 
ratio.
Provide the image at the 16:9 wide screen ratio.
Normal
Wide(16:9)
Custom adj .
Scale the image proportionally to fit the entire screen. Either side of \
image may go over the screen.
Provide the image to fit full screen size.
Full 
Expand the right and left side of images naturally without changing 
the center areas.
Natural Wide
Zoom  
Custom
Provide the last stored aspect screen image. 
Adjust the screen scale and position manually with this function.
Press the Point ► button at Custom adj . and the Custom 
adjustment menu is displayed on the screen, you can use the Point 
▲▼ buttons to choose the item you want to adjust.
 Scale H/V .............  Adjust the Horizontal/Vertical screen scale.
 H&V ......................  When set to On, the aspect ratio is fixed. 
Scale V appears dimmed and becomes 
unavailable. Adjust Scale H, then the screen 
scale is automatically modified based on the 
aspect ratio. 
 Position H/V...........Adjust the Horizontal/Vertical screen position.
 Common ..............  Save the adjusted scale or position to all the 
inputs. Press the SELECT button at Common 
to display a confirmation box. To save the 
scale or position, press the SELECT button at 
"Yes", When Custom is selected, the saved 
scale or position is used.
 Reset ...................  Reset the all adjusted values. Press the 
SELECT button at Reset to display a 
confirmation box. To reset, press the SELECT 
button at y es. 
						

							50
Video Input
This function returns all adjusted values to the factory default 
settings. Press the SELECT button at Reset to display a 
confirmation box. To reset, press the SELECT button at “Yes.”
Ceiling 
Rear 
When this function is set to On, the picture will be top/bottom and 
left/right reversed. This function is used to project the image from a 
ceiling-mounted projector.
When this function is set to On, the picture will be left/right 
reversed. This function is used to project the image from rear of 
the screen.
Keystone 
This function is used to adjust keystone distortion of the projected 
image. Use the Point ▲▼ buttons to choose the item you want to 
adjust.
Keystone
Adjust the Horizontal/Vertical keystone distortion of the  
projected image.
Standard 
 Corner correction
Adjust the corner distortion of the projected image.
Corner pattern
Choose a Corner pattern mode among Red, White, Blue, and Off.  
 Store
    Store .......Keep the keystone correction even when the AC 
                     power cord is unplugged.
    Reset ......Release the keystone correction when the AC
                     power cord is unplugged.
Press the KEYSTONE button on the remote control to switch the 
Standard (for Vertical/Horizontal) /Corner correction adjustment. 
The Standard or Corner correction adjustment dialog box 
appears. Use the Point ▲▼◄► buttons to correct the Standard 
or Corner distortion. (p.31) 
Ceiling
Rear
Reset
This function is used to project the image to a 4:3 or 16:9 or 
projection screen.
Default (16:10) ....16:10 is the aspect of the LCD panel. The 
                              original Screen Menu is available.
16:9 ......................Set to a 16:9 projection screen.
4:3 ........................Set to a 4:3 projection screen.
Screen aspect
Note:
		-	When	the	16:9	function	is	selected,	Wide(16:9)	is	not	available	in	the	PC	and	 AV	screen	(pp.42-44,	49).
		-	When	the	4:3	function	is	selected,	Natural wide	is	not	available	in	the	AV	screen	(p.49).