Eiki Projector Lc Wxl200a User Manual

							31
Basic Operation
If a projected picture still has keystone distortion after pressing the \
AUTO PC button on the remote control, correct the image manually 
as follows:
Press the KEYSTONE button on the remote control to switch the 
Standard (for Vertical/Horizontal) /Corner correction adjustment. 
The Standard or Corner correction adjustment dialog box appears. 
Use the Point ▲▼◄► buttons to correct the Standard or Corner 
distortion. The Standard or Corner correction adjustment can be 
stored (see pages 44, 50).
Note:
•	The	white	arrows	indicate	that	there	is	no	correction.
•	A	red	arrow	indicates	the	direction	of	correction.
•	An	arrow	disappears	at	the	maximum	correction.
•	If	you	press	and	hold	the	KEYSTONE	button	for
		more	than	3	seconds	while	the	Standard	or	Corner	
correction	dialog	box	is	being	displayed,	the	
Standard	or	Corner	correction	adjustment	will	be	
released.
•	The	Corner	pattern	can	be	set	to	Off,	Red,	White	or	
Blue	in	the	Corner	pattern	function.	See	"Keystone"	
on	pages	44,	50.
•	The	adjustable	range	is	limited	depending	on	the	
input	signal.	
•	Standard	and	Corner	correction	functions	cannot	be	
adjusted	at	the	same	time.	If	one	of	the	functions	
is	adjusted,	and	then	the	other	one	will	be	reset	
automatically. Reduce the top left corner part with the Point ►▼ buttons. Reduce the top right corner part with the Point ◄▼ buttons.  
Reduce the bottom left corner part with the Point ►▲ buttons. Reduce the bottom right corner part with the Point ◄▲ buttons.  
Press the KEYSTONE button on the remote control to switch 
Corner correction adjustment, press the SELECT button on the 
remote control to select the corner you want to adjust. 
Reduce the right part with Point ► button.  
Reduce the upper width with the Point ▲ button. 
Reduce the left part with Point ◄ button.  
Reduce the lower width with the Point ▼ button.  
Press the SELECT button 
Press the SELECT button 
Press the SELECT button 
Press the SELECT button 
The top left corner adjustment as an example:
Press the Point ▼ button
Press the Point ► button
Keystone Correction
Standard
Corner correction
POINT 
▲▼◄►buttons
KEySTONE button 
						

							32
Note:   You	can	choose	the	pattern	of	Pointer	(Dot/Arrow/Finger)	in	the	Setting	Menu	(p.60)
You can move the Pointer of the projector with the remote control to emph\
asize a part of the projected image.  
Press the POINTER button to activate the Pointer function.1
2
3To cancel the Pointer function, press the POINTER button 
again or press any other button. 
Use the MOUSE POINTER button to move the Pointer. 
The remote control can be used as a wireless mouse for your computer. 
Before operating the wireless mouse, connect your computer and the proje\
ctor with a USB cable (p.19).
When the Pointer function is used, the wireless mouse is not available. \
When a USB cable is connected to the computer and the projector, turn on the projector first, then the computer. If you 
turn on the computer first, the wireless mouse function may not operate \
properly.
1
2
Basic Operation
Pointer Function
Wireless Mouse Operation

DotArrowFinger
MOUSE POINTER 
button
POINTER button
Move the pointer on the 
screen with this button. 
MOUSE POINTER button
R-CLICK buttonL-CLICK button
Acts as right (click) mouse 
button while the projector 
and a computer are 
connected with a USB 
cable.
Acts as left (click) 
mouse button 
while the projector 
and a computer 
are connected 
with a USB cable. 
						

							33
The input source changes each time you press the INPUT button on the side control or the remote control as follows:
 Input 1→ Input 2→ Input 3 → ...
Before using the INPUT button on the side control or the remote control, you must select a cor\
rect input source by On-
Screen Menu and the latest input source will be displayed.
Input Selection
Press the INPUT 1, INPUT 2, or INPUT 3 button on the remote control. The input source appears on the screen as you 
press each button. Select the connected input source.
INPUT 1 button
Input 1
RGB (PC analog)
RGB (Scart)
HDMI
INPUT 2 button
Input 2
Video
y,Pb/Cb,Pr/Cr
RGB
INPUT 3 button
Input 3
Video
y,Pb/Cb,Pr/Cr
S-video
Side ControlRemote Control
* Only the Input button function is set Mode 1 in the Setting menu, the INPUT button is used for switching input source 
(p.51).
INPUT button*
Direct Operation
Remote Control Operation
Side Control/Remote Control Operation
Remote Control
INPUT button*
INPUT 1/2/3  
buttons 
						

							34
INPUT MENU
When your computer is connected to the INPUT 1 (ANALOG) 
terminal, select RGB (PC analog).
RGB(PC analog)
Note:
			 Input	source	changes	if	the	INPUT	1	button	on	the	remote	control	is	pressed.
When connecting the computer output [5 BNC Type (Green, Blue, 
Red, Horiz. Sync, and Vert. Sync.)] from the computer to G, B, R, 
H/HV, and V jacks:
Input Selection
When your computer is connected to the INPUT 2 (5 BNC 
INPUT JACKS) terminal, select RGB.
RGB 
1
2
3
Press the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select Input and then press the 
Point ► or the SELECT button. 
Use the Point ▲▼ buttons to select the desired input and 
then press the Point ► button to access the submenu items. 
Use the Point ▲▼ buttons to select the desired source and 
then press the SELECT button.
Input 1RGB(PC analog)
RGB(Scart)
HDMI
Y , Pb/Cb,Pr/Cr
INPUT 2 MENU
INPUT 1 MENU
Computer Input Source Selection
WHEN SELECTING INPUT 1 
(COMPUTER INPUT TERMINALS )
WHEN SELECTING INPUT 2 (5 BNC INPUT jACKS )
Menu Operation 
						

							35
When the video input signal is connected to the 
Y-Pb/Cb-Pr/Cr jacks, select y,Pb/Cb,Pr/Cr.
When the video input signal is connected to the 
VIDEO jack, select Video.
When the video input signal is connected to the 
S-VIDEO jack, select S-video.
When connecting to video equipment, select the type of Video source 
in the Source Select Menu. 
When the video input signal is connected to the 
Y-Pb/Cb-Pr/Cr jacks, select y,Pb/Cb,Pr/Cr.
When the video input signal is connected to the 
VIDEO jack, select Video.
When connecting to video equipment, select the type of Video source 
in the Source Select Menu. 
Video
y,Pb/Cb,Pr/Cr
Video
S-video
Input Selection
When connecting to video equipment, select the type of Video 
source in the Source Select Menu. 
INPUT 1 MENU
HDMI
RGB(Scart)
When scart video equipment is connected to the INPUT 1 
(ANALOG) terminal, select RGB (Scart).
When the video signal is connected to the HDMI terminal, 
select HDMI.
INPUT 2 MENU
INPUT 3 MENU
y,Pb/Cb,Pr/Cr
1
2
3
Press the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select Input and then press the 
Point ► or the SELECT button. 
Use the Point ▲▼ buttons to select the desired input and 
then press the Point ► button to access the submenu items. 
Use the Point ▲▼ buttons to select the desired source and 
then press the SELECT button.
Video Input Source Selection
Menu Operation
Note:
	 •	 When	the	video	input	signal	is	connected	to	the	 Y-Pb/Cb-Pr/Cr	jacks,	Y,Pb/Cb,Pr/Cr takes	precedence	of	RGB.	 •	Y,Pb/Cb,Pr/Cr	input	can	accept	the	component	signal	and	the	analog	RGB	signal.	When	analog	RGB	signal	is	not	recognized	in	 Y,Pb/Cb,Pr/Cr	input	source,	set	to	RGB	input	manually.
WHEN SELECTING INPUT 1 (COMPUTER INPUT 
TERMINALS )
WHEN SELECTING INPUT 2 (5 BNC INPUT jACKS )
WHEN SELECTING INPUT 3 (AV TERMINALS ) 
						

							36
Computer Input
PC System Menu
PC System Menu1
2
PC system can also be selected manually.
The PC System Menu  Selected system is    displayed.
Press the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select Input and then press the Point 
► or the SELECT button. 
Use the Point ▲▼ buttons to select System and then press 
the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired system and 
then press the SELECT button.3
Systems in this dialog box can be selected.
Customized Mode (1-10) set in 
the PC adjust Menu (pp.38-39).
This projector automatically tunes to various types of computers with it\
s Multi-scan system and Auto PC adjustment. If a 
computer is selected as a signal source, this projector automatically de\
tects the signal format and tunes to project a proper 
image without any additional settings (Signal formats provided in this \
projector are shown on pages 82-83).
One of the following messages may appear when:
When the projector cannot recognize the connected 
signal conforming to the provided PC Systems, Auto 
is displayed on the System Menu box and the Auto PC 
adjustment function works to display proper images. 
If the image is not projected properly, a manual 
adjustment is required (pp.38-39).
There is no signal input from the computer. Check the 
connection between your computer and the projector 
(See “Troubleshooting” on pp.73-75.).
Auto
-----
The preset system is manually adjusted in the PC 
adjust Menu. The adjusted data can be stored in Mode 
1-10 (pp.38-39).
Mode 1
PC Systems provided in this projector is chosen.  The 
projector chooses a proper system provided in the 
projector and displays it.  
SVGA 1
*Mode 1 and SVGA 1 are examples.  
Computer System Selection
Automatic Multi-Scan System
Selecting Computer System Manually 
						

							37
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Position H and Position V to conform 
to your computer. 
To store the adjusted parameters .The adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by selecting Mode in PC SYSTEM Menu (p.36). See “Manual PC Adjustment” on pages 38-39.
Note:
	 •	 Fine	sync,	Total	dots,	Position	H	and	Position	V		of	certain	computers	cannot	be	fully	adjusted	with	the	Auto	PC	Adjustment	function.	When	the	image	is	not	provided	properly	with	this	operation,	manual	adjustments	are	required	(pp.38-39).	 •	 The	Auto	PC	adjustment	cannot	be	operated	when	480i,	575i,	480p,	575p,	720p,	1035i, 1080i or	1080p	is	selected	in	the	PC	System	Menu	(p.36),	or	when	the	signal	is	coming	from	the	HDMI	terminal.	 •	 Depending	on	the	condition	of	signals	and	the	type	and	length	of	cables,	the	signals	may	not	be	properly	viewed.
The Auto PC adjustment function can be operated directly by 
pressing the AUTO PC button on the remote control.
Remote Control
Computer Input
PC adjust MenuPress the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select PC adjust and then press 
the Point ► or the SELECT button.
1
2Use the Point ▲▼ buttons to select Auto PC adj . and then 
press the SELECT button.
Auto PC adj.
Fine sync
T otal dots                                                               1\
366
Position H                                                              \
 0
Position V                                                              \
 0
Current mode
Clamp                                                                   \
  0
Display area H                                                       102\
4
Display area V                                                        76\
8
Reset
Mode free
Store                                                              
0
Use the Point ▲▼ buttons to select Auto PC adj . and press the SELECT button.Please wait . . . appears while the Auto PC adjustment is in process.
Auto PC Adjustment
Direct Operation
Menu Operation
Auto PC adj .
AUTO PC 
button 
						

							38
Some computers employ special signal formats which may not be tuned by M\
ulti-Scan system of this projector. Manual PC 
Adjustment enables you to precisely adjust several parameters to match t\
hose special signal formats. The projector has 
10 independent memory areas to store those parameters manually adjusted.\
 It allows you to recall the setting for a specific 
computer. 
Use  the  Point ◄► buttons  to  adjust  the  value,  eliminating  a  flicker 
from the image displayed (from 0 to 31).
Use the Point ◄► buttons to adjust the number of total dots in one 
horizontal period to match your PC image.
Use the Point ◄► buttons to adjust the horizontal picture position.
Use the Point ◄► buttons to adjust the vertical picture position.
Press  the  SELECT  button  to  show  H-sync  freq.  and  V-sync  freq.  of  
the connected computer.
Use  the  Point ◄►  buttons  to  adjust  the  clamp  level.  When  the 
image has dark bars, try this adjustment.
Use  the  Point ◄►  buttons  to  adjust  the  horizontal  area  displayed 
by this projector.
Use the Point ◄► buttons to adjusts the vertical area displayed by 
this projector.
Computer Input
PC adjust Menu1
2
Press the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select PC adjust and then press the 
Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired item and then 
press the SELECT button to display the adjustment dialog box. 
Use the Point ◄► buttons to adjust the setting value.
Auto PC adj.
Fine sync
T otal dots                                                               1\
366
Position H                                                              \
 0
Position V                                                              \
 0
Current mode
Clamp                                                                   \
  0
Display area H                                                       102\
4
Display area V                                                        76\
8
Reset
Mode free
Store                                                              
0
Fine sync
Total dots
Position H
Position V
Current mode
Clamp
Display area H
Display area V
Manual PC Adjustment 
						

							39
Computer Input
Note:
•	Display area (H/V)	cannot	be	selected	when	480i,	575i,	
480p,	575p,	720p,	1035i,	1080i or 1080p	is	selected	in	the	PC	
System	Menu	(p.36).
•	When	input	computer	signal	to	the	projector,	PC	adjust	function
will	become	available.
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7
Mode 8
Mode 9
Mode 10
0
0T o tal dots                                 1344
Position H                                  255
Position V                                    34
Display area H                         1024 
Display area V                           768
Where to free?
store?Store
T o tal dots
Position H
Position V
Display area H
Display area V0
0
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7 
Mode 8
Mode 9
Mode 10Free
0
0T o tal dots                                 1344
Position H                                  255
Position V                                    34
Display area H                         1024 
Display area V                           768
Where to store?
Vacant
This mode has stored parameters.
Values of Total dots, Position H, Position V, Display area H and Display area V.
Press the SELECT button to store the data.
Press the MENU button to close this dialog box.
Mode free
Store
To store the adjusted data, select Store and then press the Point ► or the SELECT button. Move the highlight to one of the Modes 1 to 10 in which you want to store, and then press the SELECT button.
To clear the stored data, select Mode free and then press the Point ► or the SELECT button. Move the highlight to the Mode that you want to clear and then press the SELECT button.
To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select y es. All adjustments will return to their previous figures.  
Reset
Mode free
Store
Press the SELECT button to clear the stored data. 
						

							40
1
2
Normal picture level preset on the projector.
Picture level with improved halftone for graphics.
U s e r   p r e s e t   p i c t u r e   a d j u s t m e n t   i n   t h e   I m a g e   a d j u s t   M e n u  
(pp.41-42).
Computer Input
Image select Menu
Press the MENU button to display the On-Screen Menu. 
Use the Point ▲▼ buttons to select Image select and 
then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired item 
and then press the SELECT button.
Image Level Selection
Menu Operation
Standard
Real
Image 1–10
For viewing pictures in a bright room.
Dynamic