Eiki Projector Lc Wxl200a User Manual
Have a look at the manual Eiki Projector Lc Wxl200a User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 422 Eiki manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 83
83
Appendix
When the input signal is digital from HDMI terminal, refer to the chart \
below.
Note:
•Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed.•Specifications are subject to change without notice.•You might be able to project images even when signals other than above are inputted, however the functions of the
projector could be limited.•Depending on your PC settings, the digital signals of your PC may not be projected correctly. In...](http://img.usermanuals.tech/thumb/1702/88945/w64_eiki-lc-wxl200a-manual_d-82.png "Page 83
83
Appendix
When the input signal is digital from HDMI terminal, refer to the chart \
below.
Note:
•Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed.•Specifications are subject to change without notice.•You might be able to project images even when signals other than above are inputted, however the functions of the
projector could be limited.•Depending on your PC settings, the digital signals of your PC may not be projected correctly. In...")
![Page 85
85
The lens of this projector can be replaced with other optional lens. This feature enables you to use the projector for wide variety of uses.For installation and replacement of the lens, always contact the sales d\
ealer. The projector lens must be installed or replaced by well-trained sales or service engineers. Do not attempt to install an\
d replace the lens by yourself as it may cause injury.
Do not hold the lens when carrying or lifting the projector. It may cause serious damage to the projector....](http://img.usermanuals.tech/thumb/1702/88945/w64_eiki-lc-wxl200a-manual_d-84.png "Page 85
85
The lens of this projector can be replaced with other optional lens. This feature enables you to use the projector for wide variety of uses.For installation and replacement of the lens, always contact the sales d\
ealer. The projector lens must be installed or replaced by well-trained sales or service engineers. Do not attempt to install an\
d replace the lens by yourself as it may cause injury.
Do not hold the lens when carrying or lifting the projector. It may cause serious damage to the projector....")
![Page 87
87
Write down the PIN code number in the column below and keep it with this \
manual securely. If you forgot or lost
the number and unable to operate the projector, contact the service center.
Factory default set No: 1 2 3 4*
Factory default set No: 4 3 2 1*
* S h o u l d t h e f o u r - d i g i t n u m b e r b e
changed, the factory set number will
be invalid.
Put the label below (supplied) on in a prominent place of
the projector’s body while it is locked with a PIN code.
While the...](http://img.usermanuals.tech/thumb/1702/88945/w64_eiki-lc-wxl200a-manual_d-86.png "Page 87
87
Write down the PIN code number in the column below and keep it with this \
manual securely. If you forgot or lost
the number and unable to operate the projector, contact the service center.
Factory default set No: 1 2 3 4*
Factory default set No: 4 3 2 1*
* S h o u l d t h e f o u r - d i g i t n u m b e r b e
changed, the factory set number will
be invalid.
Put the label below (supplied) on in a prominent place of
the projector’s body while it is locked with a PIN code.
While the...")
![Page 89
89
Appendix
This projector provides a function to control and monitor the projector'\
s operations by using the RS-232C serial port.
Connect a RS-232C serial cross cable to CONTROL PORT
on the projector and serial port on the PC. (See p.19)
Launch a communication software provided with PC and
setup the communication condition as follows:
1
2
3
Baud rate : 9600 / 19200 bps
Parity check : none
Stop bit : 1
Flow control : none
Data bit : 8
Type the command for controlling the projector and then...](http://img.usermanuals.tech/thumb/1702/88945/w64_eiki-lc-wxl200a-manual_d-88.png "Page 89
89
Appendix
This projector provides a function to control and monitor the projector'\
s operations by using the RS-232C serial port.
Connect a RS-232C serial cross cable to CONTROL PORT
on the projector and serial port on the PC. (See p.19)
Launch a communication software provided with PC and
setup the communication condition as follows:
1
2
3
Baud rate : 9600 / 19200 bps
Parity check : none
Stop bit : 1
Flow control : none
Data bit : 8
Type the command for controlling the projector and then...")
![Page 90
90
The command is sent from PC to the projector with the
format below;
'C' [Command] 'CR'
Command: two characters (refer to the command
table below.
-The projector decodes the command and returns the 'ACK'
with the format below;
'ACK' 'CR'
-When the projector can not decode the command, it returns
with format below.
‘?’ ‘CR’
Format
Appendix
Functional Execution Command
CommandFunction
C00Turn the projector ON
C01Turn the projector...](http://img.usermanuals.tech/thumb/1702/88945/w64_eiki-lc-wxl200a-manual_d-89.png "Page 90
90
The command is sent from PC to the projector with the
format below;
'C' [Command] 'CR'
Command: two characters (refer to the command
table below.
-The projector decodes the command and returns the 'ACK'
with the format below;
'ACK' 'CR'
-When the projector can not decode the command, it returns
with format below.
‘?’ ‘CR’
Format
Appendix
Functional Execution Command
CommandFunction
C00Turn the projector ON
C01Turn the projector...")
![Page 91
91
Appendix
The command is sent from PC to the projector with the
format below;
'CR' [Command] 'CR'
Command: one character (refer to the command table
below.
The projector decodes the command and returns the
'Character string' with the format below;
Format
The tables on page 90 and 91 show the typical command lists for controll\
ing the projector. Please consult your local dealer
for further information of other commands.
CommandFunctionProjector
ReturnProjector...](http://img.usermanuals.tech/thumb/1702/88945/w64_eiki-lc-wxl200a-manual_d-90.png "Page 91
91
Appendix
The command is sent from PC to the projector with the
format below;
'CR' [Command] 'CR'
Command: one character (refer to the command table
below.
The projector decodes the command and returns the
'Character string' with the format below;
Format
The tables on page 90 and 91 show the typical command lists for controll\
ing the projector. Please consult your local dealer
for further information of other commands.
CommandFunctionProjector
ReturnProjector...")
91
Appendix
The command is sent from PC to the projector with the
format below;
'CR' [Command] 'CR'
Command: one character (refer to the command table
below.
The projector decodes the command and returns the
'Character string' with the format below;
Format
The tables on page 90 and 91 show the typical command lists for controll\
ing the projector. Please consult your local dealer
for further information of other commands.
CommandFunctionProjector
ReturnProjector status
CR0Status Read
00Power On
80Stand-by mode
40Countdown
20Cooling down
10Power Malfunction
28Cooling down at the temperature anomaly
24Cooling down at Power Management mode
04Power Management mode after Cooling down
21Cooling down after the projector is turned off when the lamps
are out.
81Stand-by mode after Cooling down when the lamps are out.
88Stand-by mode after Cooling down at the temperature
anomaly.
2CCooling down when the projector is turned off by the shutter
management function.
8CStand-by mode after cooling down by the shutter management
function.
CR6Temperature ReadS1 S2 S3
S1 = Temperature at Sensor 1 (˚C)
S2 = Temperature at Sensor 2 (˚C)
S3 = Temperature at Sensor 3 (˚C)
(ex.) S1 = 12.3˚C, S2 = 23.4˚C, S3 = 34.5˚C
--> The projector displays “12.3 23.4 34.5”
( For each sensor, two digit and the tenth place numbers are
displayed with a space between each temperature.)
?Communication failure
Status Read Command
MW4B U.S.A. EIKI International, Inc. 30251 Esperanza Rancho Santa Margarita CA 92688 -2132 U.S.A. Tel : 800 -242 -3454 (949) -457 -0200 Fax : 800 -457 -3454 (949) -457 -7878 E -Mail : [email protected] Deutschland & Österreich EIKI Deutschland GmbH Am Frauwald 12 65510 Idstein Deutschland Tel : 06126 -9371 -0 Fax : 06126 -9371 -14 E -Mail : [email protected] China EIKI (Shanghai) Co., Ltd. Lakeside Oasis Middle Ring Business Cent re Block 10. #16-0 7 , 1 628, Jin Sha Jiang Road, Shanghai, 200 333. Ch ina Main Line : 86-21 -3 251 -3993 Service Hot Line : 86-21 -3 251 -3995 Fax : 86-21 -3 251 -3 997 E -mail : info@eiki -china.com Canada EIKI CANADA - Eiki International, Inc. P.O. Box 156, 310 First St. - Unit 2, Midland, ON, L4R 4K8, Canada Tel : 800 -563 -3454 (705) -527 -4084 Fax : 800 -567 -4069 (705) -527 -4087 E -Mail : [email protected] Eastern Europe EIKI CZECH SPOL. s.r.o. Nad Cementárnou 1163/4a Praha 4, Podolí 147 00 Czech Republic Tel : +420 24 1 410 928 +420 241 403 095 Fax: +420 241 409 435 E -Mail : [email protected] South East Asia EIKI Industrial (M) Sdn Bhd No. 3A -2C, 4th Floor, Jalan PJU 8/3A, Perdana Business Centre, Bandar Damansara Perdana, 47820 Petaling Jaya, Selangor Malaysia Tel : +603 -772 2-4362 Fax : + 603 -772 2-4392 E -Mail : [email protected] Worldwide EIKI Industrial Company Limited. 6 -23 Teramoto , Itami -shi , Hyogo , 664 -002 6 Japan Tel : +81-72 -782 -7552 Fax : +81 -72 -782 -7590 WorldWide Website http://www.eiki.com ©2012 Eiki International, Inc.