Eiki Projector Lc Wip3000 User Manual

59
Network Control Software Application-Software Control
 Network Control Window introduction
Icon Name Description
Scan allCapture the all registered projectors’ information one 
time only.
Start Auto  ScanAccording to the system setting, get the projector 
information automatically.
Stop Auto Capture Stop scanning the projector information.
Auto SearchSearch the projector in the same network to register 
and modify the setting.
Open Project File Open project file which was saved.
Save Project File Save...

60
Maintenance of Projector
Filter
When a warning message appears to remind you to clean the air filter, please replace a 
new one as soon as possible. Please check and clean the air filter periodically.
How to clean or replace the filters
Turn off the projector, and unplug the power cord. Wait to allow the projector to cool 
down sufficiently. 
1.   Push up the white stopper of the Filter cover and remove it from the side of projector 
as shown below. 
2.   Remove the Filter cover by pushing and sliding it...

61
Maintenance of Projector
Lamp
Please turn off the projector and unplug the AC power cord. And then, let the projector 
cool down at least 60 minutes.
Replacing New Lamp(Part Number:23040034)
1. Remove the lamp door.
2.  Loosen 2 screws of the lamp holder. Hold the handle on the top of the lamp, pull out 
the lamp straight off the projector.
3. Insert new lamp, lock the lamp door firmly with 2 screws.
4. Put the lamp door on.
5. Please reset the lamp timer after replacing lamp. (P.32)
When changing...

62
Maintenance of Projector
 WARNING
The projector uses a high-pressure mercury lamp.
The explosion of lamp with a loud bang or burn out could possibly cause injury or a fire.
When the bulb bursts, it is possible for shards of glass to fly into the lamp housing; and 
for gas containing mercury to escape from the projector’s vent holes.
If the lamp has broken, do not check the inside of the projector. Please ventilate the room 
immediately.
Do not touch or bring your face close to the broken pieces since it...

63
Maintenance of Projector
Additional
- In order to ensure the safe use of your projector, please contact your dealer to inspect 
about once a year.
- Before maintenance, make sure the power cable is unplugged, allow the projector to 
cool sufficiently. The high temperature state of the projector could cause a burn in and/
or malfunction to the projector.
-Never try to maintain the inside of the projector by yourself. 

64
Troubleshooting
Indicator
The power and lamp indicators show the status of the projector. Before requesting repair, 
check the projector status using the chart below. If the problem cannot be resolved, 
contact your dealer.
In normal status~~~
POWER LAMPCONDITIONS DESCRIPTION
Blinking In 
GreenOff Stand by modeProjector is ready to be turned 
on.
Lighting In 
GreenOff On mode Projector is on and operating.
Lighting In 
Green
Blinking In Red 
( Slow )Cool down modeProjector is in cool down mode 
and...

65
Troubleshooting
Error For Machine Defects
The following problems may be confused with a machine defect. Check and follow the 
table. If it couldn’t be improved, contact your dealer.
Symptom Cause / Remedy
Projector power
does not turn onThe power cord is disconnected.
Plug the power cord into an AC outlet.
Intending to turn on the projector again during the cool down 
mode.
Wait until the cool down mode has completed.
There is no lamp and/or lamp cover is not firmly closed.
Please turn off the power...

66
Troubleshooting
Error For Machine Defects
Symptom Cause / Remedy
No audioThe projector is not connected correctly.
Check audio cable if connect correctly.
The volume is set to minimum.
Adjust the volume.
Mute is turned on.
Press the MUTE button.
Remote control is 
not workingNo battery.
Before using the remote control, please check the battery of remote 
control.
Remote signal is obstructed.
Remove the obstacle between projector and remote control. 

67
Troubleshooting
List of Supported Monitor Displays
Computer mode / HDMI table
Signal Refresh Rate (Hz) Resolution (dots)
VGA 60 640x480
VESA 60 / 72 / 75 / 85 640x480
SVGA 56 / 60 / 72 / 75 /85 800x600
XGA 60 / 70 / 75 / 85 1024x768
SXGA 70 / 75 1152x864
SXGA 60 / 75 1280x960
SXGA 60 1280x1024
WXGA 60 / 75 1280x800
WXGA+ 60/ 75 / 85 1440x900
SXGA + 60 / 75 1400x1050
UXGA 60 1600x1200
WSXGA+ 60 1680x1050
MAC 67 1280x1024 / 640x480
MAC 75 832x624
MAC 75 1024x768
MAC 75 1152x870
Component (Y, Pb, Pr/ Y,...

Appendix
Technical Specifications
•The specifications are subject to change without notice. Mechanical Information
Projector Type Short-Throw Interactive Projector
Dimensions(WxHxD)
360 x 348 x 132 mm
Net Weight 4.1 kg
Feet Adjustment up to 7°
Panel Resolution
LCD Panel System 0.59" TFT LCD Panel, 3 panels
Panel Resolution 1,280 x 800 dots
Number of Pixels 3,072,000 (1,280 x 800 x 3 panels)
Signal Compatibility
Color System PAL,SECAM,NTSC
SD/HD TV Signal 480i, 480p, 575i, 575p, 720p, 1080i and 1080p...