Eiki Projector Lc Wip3000 User Manual

49
Network Control Software Application-Software Control
   Click  (register projector), then the projectors will be shown in the Monitor 
Window as shown below.
 Monitor window
   After changing the projector setting, you can save the data by clicking  button or 
cancel by clicking 
 button.
Item Description
Projector nameShow the Host name. (16 characters at most in 
ASCII.)
IP Address Show the IP Address.
Mask Show the Subnet Mask.
Gateway Show the Gateway.
MACShow up the MAC Address.
(The default...

50
Network Control Software Application-Software Control
Sorting the projectors 
   Projector can be sorted easily by clicking the monitor window title (Group Name) or 
(Projector Name).
   After registering, you can click  button (Data single capture) in the tool bar or 
click 
 button (Start Auto Scan) to update the status.
NOTE

While Auto Scan is running to update the status, the scroll bar for the window is grayed 
out and the hidden column can not be shown. Therefore before starting Auto Scan...

51
Network Control Software Application-Software Control
Delete
  
  Select the registered projector in monitor window. Click mouse right key and select 
"Delete" to erase the registered projector data.
< Graph 6 > : Register Table. 

52
Network Control Software Application-Software Control
Projector Setting (Setting for individual projector)
   Select the registered projector in monitor window. Click mouse right key and select 
       "projector setting" to modify the registered projector data. After finishing the setting, 
you can save by clicking 
 button or cancel by clicking  button.
< Graph 7 > : Register table.
< Graph 8 > :Setting table. 

53
Network Control Software Application-Software Control
System Setting (Setting for all projectors)
 Click  button (system setting) to modify system alert setting.
Saving the setting
 
< Graph 9 >
Note: 
Alert setting in System Setting vs Projector Setting
Whenever the "
" Save button is pressed in System Setting, the value becomes 
effective for all the projectors registered.
After this if the value in Projector Setting is changed and saved, the value becomes 
effective only for the projector. 

54
Network Control Software Application-Software Control
System Setting
Monitor
Item Description
Lamp Timer Read lamp use time from projector.
Air Filter Alert Read Air Filter Timer from projector.
System Status/
Tempeture LevelRead System Status and Temperature from projector in Power On 
status.
Input Source Read Input Source Selection from projector in Power ON status.
< Table 2 >
Default Setting
Item Description
Lamp Timer Alert (Hr.)Default Setting Includes 1000/1500/2000/3000 Hours.
When Lamp Timer...

55
Network Control Software Application-Software Control
Saving the Project File
Save the Configuration above as Project File by clicking the save button in the Tool bar 
in the Monitor window before closing Network Control Software.
If it is not saved, all the configuration above will be lost.
From next time after starting this Network Control Software the configuration can be 
recovered easily by opening the Project File. 

56
Network Control Software Application-Software Control
Link(Controlling Projector)
   Select the registered projector in monitor window. Click mouse right key and select 
"Link" to show the control panel table and the projector connecting status.
< Graph 12 > : The control panel table 

57
Network Control Software Application-Software Control
   Power Control
Icon Name
Power on
Power off
   Input Source
Icon Name
Video
S-Video
Y, Pb, Pr / Y, Cb, Cr
HDMI
RGB 1
Change Input Source
   Function Key
Icon Name Icon Name
UpFreeze
DownBlank
LeftKeystone Correction +
RightKeystone Correction -
MenuIncrease Brightness
Auto SyncDecrease Brightness
MuteHigher Contrast 

58
Network Control Software Application-Software Control
 Function Key
Icon Name
Lower Contrast
Zoom In
Zoom Out
Volume Up
Volume Down
 Projector Status
Icon Name
System Status
Input Source Status
Lamp Timer
Air Filter Timer