Eiki Projector Lc Wip3000 User Manual

Part Names
9
Part Names
Projector
1 Touch Keypad
Operating system.
        Filter cover
Prevents dust and other foreign particles 
from being drawn into projector.
Remove the filter cover to clean the air 
filter.
  Foot adjust button
Lock / unlock the adjustable foot.
  Front adjustable foot
Extend and retract to adjust the projection 
angle.
 Lens Cover
Attach when not using to protect the lens 
from becoming dirty or damaged
.
 Focus ring
Use the focus ring to focus the projector 
image.
Rotate the...

10
Part Names
9 VOLUME + / -
Sound louder or lower.
110 MENU
Display or hide the OSD main menu
11 AUTO
Automatically adjust the setting to match 
the current input.
112  (POWER)
Power On / Off.
113 BLANK
Blank the projected image. The time of 
Blank mode can be set in 15 minutes, 30 
minutes or 60 minutes. The projector will 
shut down automatically after passing each 
set time.
Touch Keypad
114 INPUT
Select input source:
Note : 
If the projector can not be captured the 
signals within 15 minutes, it...

11
Part Names
Rear
A  REAR IR RECEIVER
B USB
Connect a USB cable to a computer to 
control computer Interactive functions.
C RS232
Serial data port for controlling the projector 
with a computer or other RS-232 control 
device.
D  AUDIO IN 1 & O AUDIO IN 2
Mini jack port corresponds to computer 
input. (RGB IN→AUDIO IN 1, RGB2 
→AUDIO IN 2)
E RGB IN 
Input analog RGB signal from a computer.
F HDMI
G S-VIDEO
S-Video signal from a video source.
H  COMPONENT ( Y, Pb, Pr / Y, 
Cb, Cr)
Input Component signal...

Setting Up
12
Setting Up
When installed against a wall, leave about 20cm (7.9in.) between the projector and the wall.
Please see the detail of the minimum required space on paga 6.
 
14.81  17.77  20.73  23.69  26.65  29.62   
50     60       70      80       90    100       65.0 79.0 92.0106.0120.0134.0
Distance(cm)
Image size(inch)
Arrangement
1.  Before installation, make sure that the projector is turned off and the power cord is disconnected.
2.  Do not set up and move the projector, while it is...

13
Setting Up
Power ON / OFFTurning On The Power
1.  Make sure that power cord is firmly and 
correctly connected to the projector.
2. The green Power indicator blinks slowly.
3. Remove the lens cover. 
4.  Press POWER button on the Touch Keypad 
or the remote control to turn on the projector.
5. Rotate the focus ring to adjust the focus.
Turning Off The Power
1.  Press the POWER button on the Touch 
Keypad or the remote control. The "power 
off" confirmation message will appear.
2.  Press the...

14
Setting Up
Setting Up The Projector
The projector supports the following four different projection methods. 
1. Front projection2. Rear projection
3. Rear ceiling projection
4. Front ceiling projection
Special installation is required in order to suspend the projector from the ceiling. Please ask your 
dealer for details. 
0˚180˚
270˚90˚The projector can be installed pitched by any 
angle (360 degree) without any setting in fan 
mode. As for rolling it must be within 10 degree. 

15
Setting Up
Ceiling Mounted Installation Guide 
Attach ceiling mount at four-suspension bracket fixing points when suspending from a ceiling. 
Special installation is required in order to suspend the projector from the ceiling. Please ask your 
dealer for details.
Security Anchor
The product is equipped with security anchor and PIN 
LOCK (See page 33 for detials) functions to help prevent 
unauthorized removal of the projector.MAX M4x8 mm For Mounting
WARNING
►Do not grasp the security anchor to carry...

16
Setting Up
Adjusting The Projector’s Elevation
Use the adjustable foot at the front of the projector to set the image height.
1   Holding the projector, push the foot adjust 
buttons to loosen the front adjustable foot.
12   Position the front side of the projector to the 
desired height.
3   Release the foot adjust buttons in order to 
lock the front adjustable feet.
14   Please make sure that the front adjustable 
feet are locked.
         Please rotate the adjustable feet when fine 
adjustment of...

17
Setting Up
Before starting, make sure that the projector and computer are both turned off.
Connect the computer 
Connect the computer cable from the computer to the projector's RGB IN.
Connect a computer cable from the MONITOR OUT to an external monitor to view the
signal on RGB IN. Tighten the screw on all connectors.
Connect the supplied USB cable from computer to the projector's Mouse for interactive 
function.
How To Connect
Laptop or desktop computer
AUDIO OUTMOUSERS-232AUDIO OUTHDMIVGA...

18
Setting Up
How To Connect
Laptop or desktop computer
 Connect the audio cable if necessary
1.  Please connect the audio cable to the AUDIO IN 1 if the computer cable is connected to 
the projector's RGB IN. 
2.   Please connect the audio cable to the AUDIO IN 2 if the computer cable is connected to 
the projector's RGB2. 
3.  Please connect the audio cable to the AUDIO IN 3 if the video cables are connected to 
the VIDEO / S-VIDEO / Component port of the projector.
 
When connecting HDMI...