Eiki Projector Lc Wip3000 User Manual

							59
Network Control Software Application-Software Control
 Network Control Window introduction
Icon Name Description
Scan allCapture the all registered projectors’ information one 
time only.
Start Auto  ScanAccording to the system setting, get the projector 
information automatically.
Stop Auto Capture Stop scanning the projector information.
Auto SearchSearch the projector in the same network to register 
and modify the setting.
Open Project File Open project file which was saved.
Save Project File Save the registered projector in this project.
System Setting Setting the projector system reminder message.
About Icon content description.
Exit Exit the Network software.
Register projector Register projector’s information.
Exit Cancel registered information. 
						

							60
Maintenance of Projector
Filter
When a warning message appears to remind you to clean the air filter, please replace a 
new one as soon as possible. Please check and clean the air filter periodically.
How to clean or replace the filters
Turn off the projector, and unplug the power cord. Wait to allow the projector to cool 
down sufficiently. 
1.   Push up the white stopper of the Filter cover and remove it from the side of projector 
as shown below. 
2.   Remove the Filter cover by pushing and sliding it as shown below. 
3.    Clean the filters with a vacuum cleaner except for the back side of the sponge, 
because the vacuum cleaner may suck it. Brush the sponge gently by a brush. 
(Do not clean the filters with water.)
12
3 
						

							61
Maintenance of Projector
Lamp
Please turn off the projector and unplug the AC power cord. And then, let the projector 
cool down at least 60 minutes.
Replacing New Lamp(Part Number:23040034)
1. Remove the lamp door.
2.  Loosen 2 screws of the lamp holder. Hold the handle on the top of the lamp, pull out 
the lamp straight off the projector.
3. Insert new lamp, lock the lamp door firmly with 2 screws.
4. Put the lamp door on.
5. Please reset the lamp timer after replacing lamp. (P.32)
When changing lamp, it is recommended that you change the filer at the same time. 
						

							62
Maintenance of Projector
 WARNING
The projector uses a high-pressure mercury lamp.
The explosion of lamp with a loud bang or burn out could possibly cause injury or a fire.
When the bulb bursts, it is possible for shards of glass to fly into the lamp housing; and 
for gas containing mercury to escape from the projector’s vent holes.
If the lamp has broken, do not check the inside of the projector. Please ventilate the room 
immediately.
Do not touch or bring your face close to the broken pieces since it might get into your 
eyes or mouth. In case of injury, seek medical advice immediately.
Disposal of a Lamp
Dispose of a lamp in accordance with the local recycling laws.
Do not put it to your trash.
Recycling Lamp’s laws of the USA, go to 
www.lamprecycle.org.
Recycling Product’s laws of USA, go to 
www.eiae.org.
Recycling Product’s laws of Canada, go to 
www.epsc.ca.
For more information about recycling laws, please contact local government agency or 
dealer.
CAUTION HOT
Before replacing the Lamp unit, pay attention to the following items:
1.The Lamp is optional part. Contact the dealer for replacement lamp.
2. The lamp becomes very hot when in use. Turn the power off and disconnect the power 
cord.
3.Wait for 1 Hour before replacing the lamp.
4. Do not use old lamp unit. 
						

							63
Maintenance of Projector
Additional
- In order to ensure the safe use of your projector, please contact your dealer to inspect 
about once a year.
- Before maintenance, make sure the power cable is unplugged, allow the projector to 
cool sufficiently. The high temperature state of the projector could cause a burn in and/
or malfunction to the projector.
-Never try to maintain the inside of the projector by yourself. 
						

							64
Troubleshooting
Indicator
The power and lamp indicators show the status of the projector. Before requesting repair, 
check the projector status using the chart below. If the problem cannot be resolved, 
contact your dealer.
In normal status~~~
POWER LAMPCONDITIONS DESCRIPTION
Blinking In 
GreenOff Stand by modeProjector is ready to be turned 
on.
Lighting In 
GreenOff On mode Projector is on and operating.
Lighting In 
Green
Blinking In Red 
( Slow )Cool down modeProjector is in cool down mode 
and will not respond to user 
input.
Lighting In 
Green
Blinking In Red 
( Fast )Cool down modeWhen the projector is turned on 
in 2 minutes after it was turned 
off.
In abnormal status~~~
POWER LAMPCONDITIONS DESCRIPTION
Blinking In 
Green
Blinking In Red 
( Fast )Fan fault modeThe projector has detected a 
problem of a slow internal fan 
speed. The lamp will shut off 
automatically. Contact your dealer. 
Blinking In 
GreenLighting In RedLamp cover openThe lamp cover is open or not 
closed well. Please check lamp 
cover again.
Blinking
In 
Green (Fast)Blinking In 
Red 
( Fast )High temperatureThe projector has overheated and 
shut itself down.
Correct the over temperature 
condition immediately.
1.  Check that the ventilation slots 
are free from obstructions.
2.  Check the cleanliness of the air 
filter.
Blinking In 
Green (Slow)Blinking In 
Red 
(Slow)Lamp failThe lamp does not light. Come 
to "stand by mode", and press the 
power button again. If the situation 
is the same, please contact your 
dealer. 
						

							65
Troubleshooting
Error For Machine Defects
The following problems may be confused with a machine defect. Check and follow the 
table. If it couldn’t be improved, contact your dealer.
Symptom Cause / Remedy
Projector power
does not turn onThe power cord is disconnected.
Plug the power cord into an AC outlet.
Intending to turn on the projector again during the cool down 
mode.
Wait until the cool down mode has completed.
There is no lamp and/or lamp cover is not firmly closed.
Please turn off the power and disconnect the power plug from the power 
outlet. Check if the lamp is installed or the lamp cover is firmly closed 
and turn on the power again.
Power cord has impaired.
When you touch the power cord, the indicator goes on then off, please 
remove the power cord and connect it again. If the situation is repeated, 
remove the power cord and contact your dealer.
No ImageThe input is not connected correctly.
Select the appropriate input source.
No signal input.
Connect correctly.
The lens cover is attached to the lens.
Remove the lens cover.
Colors are paleColor density and color matching are not adjusted correctly.
Adjust the RGB setting.
Color lose.
Caused by poor VGA cable connection.
Abnormal brightness 
& contrastBrightness and contrast are not adjusted correctly.
Adjust the brightness and contrast setting.
The lamp is near the end of its service life.
Replace with a new lamp.
Image is blurredThe projection lens is not focused.
Adjust the focus using the focus ring.
The lens is dirty or misty.
Clean the lens. 
						

							66
Troubleshooting
Error For Machine Defects
Symptom Cause / Remedy
No audioThe projector is not connected correctly.
Check audio cable if connect correctly.
The volume is set to minimum.
Adjust the volume.
Mute is turned on.
Press the MUTE button.
Remote control is 
not workingNo battery.
Before using the remote control, please check the battery of remote 
control.
Remote signal is obstructed.
Remove the obstacle between projector and remote control. 
						

							67
Troubleshooting
List of Supported Monitor Displays
Computer mode / HDMI table
Signal Refresh Rate (Hz) Resolution (dots)
VGA 60 640x480
VESA 60 / 72 / 75 / 85 640x480
SVGA 56 / 60 / 72 / 75 /85 800x600
XGA 60 / 70 / 75 / 85 1024x768
SXGA 70 / 75 1152x864
SXGA 60 / 75 1280x960
SXGA 60 1280x1024
WXGA 60 / 75 1280x800
WXGA+ 60/ 75 / 85 1440x900
SXGA + 60 / 75 1400x1050
UXGA 60 1600x1200
WSXGA+ 60 1680x1050
MAC 67 1280x1024 / 640x480
MAC 75 832x624
MAC 75 1024x768
MAC 75 1152x870
Component (Y, Pb, Pr/ Y, Cb, Cr)
Signal Refresh Rate (Hz) Resolution (dots)
SDTV(480i / 576i) 30 / 25 720x480 / 720x576
SDTV(480p / 576p) 60 / 50 720x480 / 720x576
HDTV(720p) 60 1280x720
HDTV(1080i / 1080p) 30 / 60 1920x1080
Composite / S-Video
Signal Refresh Rate (Hz) Resolution (dots)
TV(NTSC) 60 720x480
TV(PAL,SECAM) 50 720x576
HDMI
Signal Refresh Rate (Hz) Resolution (dots)
SDTV(480P) 60 720x480
HDTV(720P) 60 1280x720
HDTV(1080i) 60 1920x1080
HDTV(1080P) 60 1920x1080 
						

							Appendix
Technical Specifications
•The specifications are subject to change without notice. Mechanical Information
Projector Type Short-Throw Interactive Projector
Dimensions(WxHxD)
360 x 348 x 132 mm
Net Weight 4.1 kg
Feet Adjustment up to 7°
Panel Resolution
LCD Panel System 0.59" TFT LCD Panel, 3 panels
Panel Resolution 1,280 x 800 dots
Number of Pixels 3,072,000 (1,280 x 800 x 3 panels)
Signal Compatibility
Color System PAL,SECAM,NTSC
SD/HD TV Signal 480i, 480p, 575i, 575p, 720p, 1080i and 1080p
Input Scanning Frequency H-sync. 31~92kHz, V-sync. 48~120Hz
Optical Information
Projection Image Size  50"~100" Diagonal
Throw Distance 0.65M~1.34M
Projection Lens F=1.8 / f=8.2 mm
Projection Lamp 245W Lamp
Interface
Input Terminals D-SUB 15 pin x 2
HDMI x 1
Composite Video, RCA x 1
S-Video, Mini Din-4 x 1
Component Video, RCA x 3
3.5mm Mini-Stereo Audio Jack x 2
Audio RCA (Right /Left) x 2
Output Terminals D-SUB 15 pin x 1 (common with input terminal)
3.5mm Mini-Stereo Audio Jack x 1
Control Terminals RS232 DB-9 x 1
USB Type B x 1
RJ45 x 1
Audio
Speaker 8W mono speaker built-in
Power
Voltage and Power 
ConsumptionAC100~240V, 50/60Hz(full range)
Operating Environment
Operating Temperature 5W
~35W
/ 41Y
~95Y
Storage Temperature -20W
~50W
 / -4Y
~122Y